连续刚构桥的群桩基础计算模型研究

群桩基础是连续刚构最常用的基础形式之一，分析探讨了群桩基础的几种建模方法，给出了建模思路和参数取值。结合苏通大桥辅航道桥预应力混凝土连续刚构的工程需要，提出了考虑群桩基础与上部结构共同工作的计算模型，并将计算结果与不考虑桩基的模型计算结果进行了对比分析，计算方法对类似工程有直接参考价值。     

Target priority determination methods by interval-valued intuitionistic fuzzy sets with unknown attribute weights

The paper aims at the problem of multi-targets threat degree being hard to be evaluated accurately in complex air defense battlefield environments. Combined with multi-sensors information fusion and interval-valued intuitionistic fuzzy sets (IVIFS) theories, the target priority determination is studied. The score and accuracy functions of IVIFS are improved with thinking about the hesitating information in order to increase the rationality. Then, the influence factors of target priority and the nonlinear relationship between the influence factors and target priority are analyzed. Next, the algorithms for calculating the factor weights and sensor weights are given. Based on the theory of IVIFS and technique for order preference by similarity to an ideal solution (TOPSIS), two methods of target priority determination based on the IVIFS and TOPSIS are proposed. At last, an application example verifies the effectiveness and flexibility of the proposed algorithms.     

Elasto-plastic modeling of soft soil considering degradation of stiffness

The stiffness has a large influence on the behavior of soils. Its value is affected by some of the soils properties, such as the over consolidated ratio(OCR), the effective normal stress, and the plasticity index etc. In this paper, the numerical modeling of soft soils was carried out using an improved elasto-plastic S-clay1 model accounting for degradation of stiffness. The relation between the stiffness and the shear strain was established based on a large number of experimental data. The effects of strain-dependent stiffness of normally consolidated soils and over consolidated soils on the stress-strain behavior were studied through a comparison of the simulations with the experimental results of undrained triaxial compression tests. The results show that the behaviors of soils can be well predicted with the improved constitutive model, particularly before the peak stress.     

Decomposing and Cluster Refinement Design Method for Application-Specific Network-on-Chips

Along with higher and higher integration of intellectual properties (IPs) on a single chip, traditional bus-based system-on-chips (SoC) meets several design difficulties (such as low scalability, high power consumption, packet latency and clock tree problem). As a promising solution, network-on-chips (NoC) has been proposed and widely studied. In this work, a novel algorithm for NoC topology synthesis, which is decomposing and cluster refinement (DCR) algorithm, has been proposed to minimize the total power consumption of application-specific NoC. This algorithm is composed of two stages: decomposing with cluster generation, and cluster refinement. For partitioning and cluster generation, an initial low-power solution for NoC topology is generated. For cluster refinement, the clustering is optimized by performing floorplan to further reduce power consumption. Meanwhile, a good tradeoff between power consumption and CPU time can be achieved. Experimental results show that the proposed method outperforms the existing work.     

基于Ansys的矩形加筋平盖封头强度评定

将有限元方法与分析设计相结合,利用有限元分析软件Ansys对一种矩形加筋平盖封头进行强度评定。本文首先介绍瓶盖封头结构的改进。然后建立有限元模型,并进行应力求解。结果表明,此加筋平盖封头满足强度要求,与普通平盖封头相比,减小了平盖的厚度,降低了结构总重量,对平盖封头的结构改进设计具有一定指导作用。     

STX4型驮背多功能运输车车体制造工艺

介绍了STX4型驮背多功能运输车的主要结构特点,分析了车体制造过程中的控制要点和难点,同时对制造难点提出了应对措施,有效保证了STX4型驮背多功能运输车的制造质量。     

Application of digital image correlation method to in-situ dynamic strain measurement

Application of digital image correlation (DIC) method to determination of in-situ dynamic strain is presented in this study. Firstly, an integrative software is programmed based on the DIC algorithms and point-wise least-squares fitting technique. Then, simulated speckle images are generated to study the computational accuracy of this software. The experimental setup and procedures for measuring in-situ dynamic strain through both DIC and strain gauge are proposed. The DIC results are close to those measured by strain gauge. This fact reveals that DIC is a practical and effective tool for in-situ dynamic strain measurement. Finally, the full-field in-situ dynamic strain of another specimen is measured by DIC, and the overall distribution of the strain in the measurement area is clearly shown.     

融合已聚力 发展正当时

浩渺行无极,扬帆但信风。一体共发展,同向曙霞东。海事监管和航海保障,关系到国家主权、经济发展、航运与水域安全。2019年航海保障工作座谈会强调要持续推动海事监管和航海保障"一体化"融合发展,为推进交通强国建设作出新贡献、展现新形象。     

基于有限元分析的五相感应电机参数计算

以自行设计的一台五相感应电机为例,分析了多相感应电动机内部的电磁关系,建立了多相感应电机二维静、瞬态电磁场考虑边界条件的偏微分方程,并在此基础上,对五相感应电动机的暂、稳态电磁场和电机性能进行计算;分别应用场算和路算方法计算了励磁电感,并与设计值进行对比,结果表明本文所用的电磁场计算方法准确有效。