Prediction of vibrating forces on meshing gears for a gear rattle using a new multi-body dynamic model

An efficient multibody dynamic model was developed to predict the vibrating transmitted gear forces of loaded and unloaded pairs of helical gears simultaneously at all speeds. The model can also calculate the bearing forces of a manual transmission that, in turn, may be converted to rattling noises. The bending of meshing gear teeth and torsional flexibility of transmission shafts were considered and embodied effectively in the multibody dynamic model by calculating the tooth bending stiffness and adding a torsion spring on a shaft section between two gears, respectively. The reactive forces on teeth and bearings were calculated and compared using three different models that were developed for this study — an equivalent model, a rigid-body model, and a frequency-based model. The equivalent model took only 58% computation time, compared to the frequency-based method, even though the two showed very similar results.     

Dependence of fatigue limit of high-tension bolts on mean stress and ultimate tensile strength

High tension bolts in critical joints in internal combustion engines are susceptible to fatigue failure. Computeraided bolted joint design procedures require knowledge of the dependence of bolt fatigue limit on the mean stress and ultimate tensile strength. This dependence is investigated with staircase fatigue limit tests. The test results show that when the bolt fatigue limit is estimated with the nominal stress of the bolt, it decreases with increasing tensile strength and nominal mean stress. However, there is a range of the nominal mean stress where the bolt fatigue limit is almost constant. The test results are interpreted with finite element analysis.     

Design of conformal cooling channels for an automotive part

The cooling system plays a crucial role in determining the productivity and quality of an injection molding process. With the current growth of Solid Freeform Fabrication (SFF) techniques, mold designers have been striving for not only improvement in cooling system performance but also for a method to do so automatically. In this paper, a method is proposed for developing a conformal cooling system that facilitates uniform cooling over the entire mold surface with minimum cycle time. Based on the temperature distribution after the filling stage, the mold surface is split into zones which will be cooled by optimized subconformal channels obtained from the optimization process. The optimization process in which the objective function is stated as minimization of the cooling time with boundaries ensuring a realistic design will optimize the cooling system layout in terms of cooling channel size and location. Finally, all subcooling channels are combined to generate the entire conformal cooling system for the injection mold.     

Interior sound field refinement of a passenger car using modified panel acoustic contribution analysis

Panel acoustic contribution analysis (PACA) is a practical engineering tool for the reduction of interior structure-borne noise in passenger cars. In this study, the current PACA method has been improved for sound field refinement of the entire interior. Two new parameters, the “acoustic contribution sum” and the “total sound field contribution”, are introduced to analyze the interior sound field characterized with multiple field points and sound pressure peaks, and to evaluate the integrated acoustic contributions of auto body panels. In addition, a systematic methodology for automotive interior sound field refinement is also proposed on the basis of the modified PACA method. An example of a passenger car model demonstrates the application of the sound-field-refinement methodology and shows the advantage of using damping layers at optimum locations on the auto body. The example also shows that the modified PACA method has practical significance for refining the interior sound field and decreasing added mass in accord with the trend towards lightweight auto bodies.     

Improved method for analyzing automotive transmission parts (shaft/gear) manufactured using the warm shrink fitting process

There are three sub-processes associated with the assembly of an automobile transmission: heat fitting, shrink fitting, and combination fitting. In the heat fitting stage, the gear is heated to a specified temperature and then squeezed towards the outer diameter of the shaft. The stress of the heat-fitted gear depends on the yield strength of the gear. In the shrink fitting process, the gear is typically squeezed towards the shaft at room temperature using a press. An alternate method, known as warm shrink fitting, heats the already warm gear and safely squeezes it toward the shaft. The warm shrink fitting process for automobile transmission parts is becoming more commonplace, but the additional heating can cause the dimensions of the assembled parts (shaft/gear) to change with respect to both the outer diameter and the profile of the gear. As a result, there may be additional noise and vibration between gears. To address these problems, we analyzed the warm shrink fitting process using the contact pressure caused by fitting interference between the outer diameter of the shaft and the inner diameter of the gear, fitting temperature, and the profile tolerance of the gear as design parameters. In this study, a closed form equation for predicting the contact pressure and fitting load is proposed. This equation is used to develop an optimization technique for the warm shrink fitting process. The reliability of the model was verified using experimental results measured in the field, and FEM with thermal-structural coupled field analysis. Actual loads measured in the field showed good agreement with the results obtained by theoretical and finite element analysis, and expansion of the outer diameters of the gears agreed well with the results.     

Motor control of input-split hybrid electric vehicles

A motor control strategy for an input-split hybrid electric vehicle (HEV) is proposed. From a power characteristic analysis, it is found that the powertrain efficiency decreases for speed ratios at which power circulation occurs. Using dynamic models of an input-split HEV powertrain, a motor-generator control algorithm for obtaining high system efficiency is designed by inversion-based control. The performance of the control algorithm is evaluated by the simulator which is developed based on PSAT, and simulation results are compared with the test results. It is found that, even if the engine thermal efficiency is sacrificed by moving the engine operation point from the OOL for the control strategy, improved overall powertrain system efficiency can be achieved by the engine operation that gives a relatively high efficiency from the viewpoint of the overall powertrain efficiency. The control algorithm developed can be used in design of future electric vehicles.     

Sensor fusion-based lane detection for LKS+ACC system

This paper discusses the market trends and advantages of a safety system integrating LKS (Lane Keeping System) and ACC (Adaptive Cruise Control), referred to as the LKS+ACC system, and proposes a method utilizing the range data from ACC for the sake of lane detection. The overall structure of lane detection is the same as the conventional method using monocular vision: EDF (Edge Distribution Function)-based initialization, sub-ROI (Region Of Interest) for left/right and distance-based layers, steerable filter-based feature extraction, and model fitting in each sub-ROI. The proposed method adds only the system for confining lane detection ROI to free space that is established by range data. Experimental results indicate that such a simple adaptive ROI can overcome occlusion of lane markings and disturbance of neighboring vehicles.     

Driving environment assessment using fusion of in- and out-of-vehicle vision systems

Because the overall driving environment consists of a complex combination of the traffic Environment, Vehicle, and Driver (EVD), Advanced Driver Assistance Systems (ADAS) must consider not only events from each component of the EVD but also the interactions between them. Although previous researchers focused on the fusion of the states from the EVD (EVD states), they estimated and fused the simple EVD states for a single function system such as the lane change intent analysis. To overcome the current limitations, first, this paper defines the EVD states as driver’s gazing region, time to lane crossing, and time to collision. These states are estimated by enhanced detection and tracking methods from in- and out-of-vehicle vision systems. Second, it proposes a long-term prediction method of the EVD states using a time delayed neural network to fuse these states and a fuzzy inference system to assess the driving situation. When tested with real driving data, our system reduced false environment assessments and provided accurate lane departure, vehicle collision, and visual inattention warning signals.     

HCCI combustion characteristics during operation on DME and methane fuels

The Homogeneous Charge Compression Ignition (HCCI) engine has attracted much interest because it can simultaneously achieve high efficiency and low emissions. However, the ignition timing is difficult to control because this engine has no physical ignition mechanism. In addition, combustion proceeds very rapidly because the premixed mixture ignites simultaneously at multiple locations in the cylinder, making it difficult to increase the operating load. In this study, an HCCI engine was operated using blended test fuels comprised of dimethyl ether (DME) and methane, each of which have different ignition characteristics. The effects of mixing ratios and absolute quantities of the two types of fuel on the ignition timing and rapidity of combustion were investigated. Cool flame reaction behavior, which significantly influences the ignition, was also analyzed in detail on the basis of in-cylinder spectroscopic measurements. The experimental results revealed that within the range of the experimental conditions used in this study, the quantity of DME supplied substantially influenced the ignition timing, whereas there was little observed effect from the quantity of methane supplied. Spectroscopic measurements of the behavior of a substance corresponding to HCHO also indicated that the quantity of DME supplied significantly influenced the cool flame behavior. However, the rapidity of combustion could not be controlled even by varying the mixing ratios of DME and methane. It was made clear that changes in the ignition timing substantially influence the rapidity of combustion.     

拥挤条件下公交系统的拟动态均衡配流模型

论文考虑了由于公交线路运营能力不足造成的车站排队拥挤现象,在此基础上构造了拥挤条件下公交系统的拟动态均衡配流模型.该模型可自动估计不同时段内拥挤条件下的公交流量和车站的乘客排队,特别是在非常拥挤的情况下(即乘客需求超过公交网络运营能力)也能够进行流量分配,并确定车站的乘客排队长度.因此,该模型较好地反映了公交网络的拥挤效应.所给算例说明了不同需求条件下该公交均衡配流模型的应用.