Comparison study on characteristics of nano-sized particle number distribution by using condensation particle counter calibrated with spray and soot type particle generation methods

In the year 2011, the Particle Measurement Program (PMP) in Europe started the regulation of the diesel vehicle’s nano-sized particle number density (PN) due to its high degree of harm to the human body. Concretely, the standard level of PN emission was introduced in the Euro 5+ and 6 emissions regulation with a limit (<6.0 × 10¹¹#/km) for diesel light-duty vehicle. Therefore, the determination of suitable and sophisticated instruments for reliable particle sampling and analysis was essential in taking exact experimental data. Now, among the PN emission measuring devices suggested by the PMP, condensation particle counter (CPC) is a key equipment for measuring the particle number density in real time and it has been used extensively. However, CPC can cause different results depending on operating conditions of the saturator and condensation that induce different rates of particle growth. This study was conducted to analyze the effect of CPC calibrated by a two-particle generator with spray and soot type methods applied on the nano-sized particle distribution’s parameters such as number concentration and linearity. Also, in order to ensure the reliability for particle sensor system named as PPS, which had emerged as a useful diagnostic to making spatially and temporally resolved quantitative measurements of diesel PN concentration, it was compared with calibrated CPC system. As a result, nano-sized particle measuring system with CPC calibrated by spray type particle generator had a much higher counting efficiency, indicating a larger nano size available than soot type particle generator. And, comparative experimental results on the correlation between the particle number of CPC to a reflectance PPS system showed that above 5,000 #/cm ³ in number concentrations measured by CPC as well as PPS were found to be similar with good linear relationship.     

Design of power split transmission: Design of dual mode power split transmission

The power split type hybrid system transmits engine power by dividing it into the electrical unit and the mechanical unit. Its power transmission efficiency is highest at the mechanical point (MP), where the full power is transmitted to the mechanical unit. In this study, the equation for the MP was derived for the gear ratios of a general 4-node lever model. The MP characteristics for the transmission ratio (TR) of the input split and compound split structures were examined using the equation derived. Using the examined input split and compound split structures, a systematic design method for the dual mode power split transmission was proposed. In the dual mode power split transmission, the MP could be positioned at the desired TR, and the input split and compound split modes could be selectively used according to the clutch combination, which leads to the operation of the vehicle within a high system efficiency range.     

Robust lane markings detection and road geometry computation

Detection of lane markings based on a camera sensor can be a low-cost solution to lane departure and curve-over-speed warnings. A number of methods and implementations have been reported in the literature. However, reliable detection is still an issue because of cast shadows, worn and occluded markings, variable ambient lighting conditions, for example. We focus on increasing detection reliability in two ways. First, we employed an image feature other than the commonly used edges: ridges, which we claim addresses this problem better. Second, we adapted RANSAC, a generic robust estimation method, to fit a parametric model of a pair of lane lines to the image features, based on both ridgeness and ridge orientation. In addition, the model was fitted for the left and right lane lines simultaneously to enforce a consistent result. Four measures of interest for driver assistance applications were directly computed from the fitted parametric model at each frame: lane width, lane curvature, and vehicle yaw angle and lateral offset with regard the lane medial axis. We qualitatively assessed our method in video sequences captured on several road types and under very different lighting conditions. We also quantitatively assessed it on synthetic but realistic video sequences for which road geometry and vehicle trajectory ground truth are known.     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

基于出行链理论的城际旅客出行特征研究

在传统"四阶段法"不满足城际出行研究要求的情况下,借鉴出行活动分析理论对城镇群内城际出行行为进行研究。通过构建城际出行链理论模型,结合长江三角洲城镇群旅客城际出行调查数据,采用统计分析方法,探讨了城镇群内旅客城际出行全过程的时空变化规律,分析了各类客流在城际出行不同阶段的差异性。     

卵砾石层管推进工程超挖及卡钻对管材与土壤互制行为的影响研究

非明挖工法在都市施作时,常因困难地质(如卵砾石层)或障碍物而造成施工困难、工期延误或发生灾损。本文主要针对非明挖施工法里的管推进施工法(Pipe-jacking Method),探讨管推进工法施工时可能遭遇的困难,以及施工困难状况下之管材土体互制行为。探讨的施工困难包括超挖、挤压、卡钻等问题。本研究针对超挖范围、卡钻位置、阻力大小以及推进力施加位置等,以ABAQUS有限元素软件进行三维数值仿真,探讨直线推进施工中的问题。     

A study of the environmental impacts of intelligent automated vehicle control at intersections via V2V and V2I communications

This article presents a novel intersection traffic management system for automated vehicles and quantifies its impact on fuel consumption and greenhouse gas emissions of CO₂ relative to traditional traffic signal and roundabout intersection control. The developed intelligent traffic management (ITM) techniques, which are based on a spatiotemporal reservation scheme, ensure that vehicles proceed through the intersection without colliding with other vehicles while at the same time reducing the intersection delay and environmental impacts. Specifically, the spatiotemporal reservation scheme provides each vehicle a collision-free path that is decomposed into a speed profile along with navigational instructions. The integration of the developed microscopic traffic simulator with instantaneous emission model, provides improved assessments of the environmental impact of traffic control strategies at intersections. The simulator architecture integrates several ITM algorithms, vehicle sensors, V2V/V2I communications, and emission and fuel consumption models. Each vehicle is modeled by an agent and each agent provides information depending on the specific vehicle sensors. The ITM system is supported by V2V and V2I communications, allowing the exchange of information among vehicles and infrastructure. The data include the estimated vehicle position and speed. Compared with traditional traffic management techniques, the simulation results prove that the proposed ITM system reduces CO₂ emissions significantly. The research also shows that these reductions are more significant when the traffic flow increases.     

不同加载幅值下考虑层间界面条件和侧向剪力作用的柔性铺面响应

该文进行了一个三维有限元参数量化的粘弹性路面响应研究,由于不同的轮胎配置:双轮和宽基轮胎在3种温度(5、25和40℃)和两种速度(8、72 km/h);还有影响路面响应的3种因素:移动车轮荷载幅值(连续,梯形),层间界面条件(简单的摩擦和粘弹性模型)和横向力共同对路面响应的影响进行了研究.研究发现连续加载幅值,不但可以模拟路面对运动轮荷载的响应,并且是一种比目前使用的梯形荷载幅值更准确的研究模型.粘弹性模型极大地提高了双轮胎对预测路面的响应,而简单的摩擦模型更接近宽基轮胎的实地测量.侧向剪力是积极改善预测轮底的表面磨损和底部热拌沥青(沥青)基层的较小程度上的应变.研究表明:使用连续加载幅值和非均匀压力分布模拟移动轮,侧向剪切力和适当的界面摩擦可显著改善有限元模型对车辆加载路面响应的预测能力.     

Design and implementation of a new clamping force estimator in Electro-Mechanical Brake systems

In this paper, an improved clamping force estimator is proposed for Electro-Mechanical Brake (EMB) systems by using the motor rotor position information and the hysteresis characteristics of mechanical parts in the EMB. A cascaded type of a force/position control system with a force sensor or an estimator was designed and implemented to control the clamping force and to keep the clearance gap in EMB systems. The EMB Hardware-In-the-Loop-Simulation (HILS) results show that the proposed force estimator yields better estimation performance than the existing estimator and that the clamping force control system based on the estimator can be also used for the fault tolerant control of the system.