Analysis of unsteady flow over Offshore Wind Turbine in combination with different types of foundations

Environmental effects have an important influence on Offshore Wind Turbine (OWT) power generation efficiency and the structural stability of such turbines. In this study, we use an in-house Boundary Element (BEM)—panMARE code—to simulate the unsteady flow behavior of a full OWT with various combinations of aerodynamic and hydrodynamic loads in the time domain. This code is implemented to simulate potential flows for different applications and is based on a three-dimensional first-order panel method. Three different OWT configurations consisting of a generic 5 MW NREL rotor with three different types of foundations (Monopile, Tripod, and Jacket) are investigated. These three configurations are analyzed using the RANSE solver which is carried out using ANSYS CFX for validating the corresponding results. The simulations are performed under the same environmental atmospheric wind shear and rotor angular velocity, and the wave properties are wave height of 4 m and wave period of 7.16 s. In the present work, wave environmental effects were investigated firstly for the two solvers, and good agreement is achieved. Moreover, pressure distribution in each OWT case is presented, including detailed information about local flow fields. The time history of the forces at inflow direction and its moments around the mudline at each OWT part are presented in a dimensionless form with respect to the mean value of the last three loads and the moment amplitudes obtained from the BEM code, where the contribution of rotor force is lower in the tripod case and higher in the jacket case and the calculated hydrodynamic load that effect on jacket foundation type is lower than other two cases.     

Three-dimensional fluid-structure interaction case study on cubical fluid cavity with flexible bottom

In this paper, we report our study on a numerical fluid-structure interaction problem originally presented by Mok et al.(2001) in two dimensions and later studied in three dimensions by Valdés Vazquez(2007), Lombardi(2012), and Trimarchi(2012). We focus on a 3D test case in which we evaluated the sensitivity of several input parameters on the fluid and structural results. In particular, this analysis provides a starting point from which we can look deeper into specific aspects of these simulations and analyze more realistic cases, e.g., in sails design. In this study, using the commercial software ADINATM, we addressed a well-known unsteadiness problem comprising a square box representing the fluid domain with a flexible bottom modeled with structural shell elements. We compared data from previously published work whose authors used the same numerical approach, i.e., a partitioned approach coupling a finite volume solver(for the fluid domain) and a finite element solver(for the solid domain). Specifically, we established several benchmarks and made comparisons with respect to fluid and solid meshes, structural element types, and structural damping, as well as solution algorithms. Moreover, we compared our method with a monolithic finite element solution method. Our comparisons of new and old results provide an outline of best practices for such simulations.     

A numerical study on piezoelectric energy harvesting by combining transverse galloping and parametric instability phenomena

This paper aims to numerically investigate the effects of parametric instability on piezoelectric energy harvesting from the transverse galloping of a square prism. A two degrees-of-freedom reduced-order model for this problem is proposed and numerically integrated. A usual quasi-steady galloping model is applied, where the transverse force coefficient is adopted as a cubic polynomial function with respect to the angle of attack. Time-histories of nondimensional prism displacement, electric voltage and power dissipated at both the dashpot and the electrical resistance are obtained as functions of the reduced velocity. Both, oscillation amplitude and electric voltage, increased with the reduced velocity for all parametric excitation conditions tested. For low values of reduced velocity, 2:1 parametric excitation enhances the electric voltage. On the other hand, for higher reduced velocities, a 1:1 parametric excitation (i.e., the same as the natural frequency) enhances both oscillation amplitude and electric voltage. It has been also found that, depending on the parametric excitation frequency, the harvested electrical power can be amplified in 70% when compared to the case under no parametric excitation.     

Vortex-induced vibration of a tension leg platform tendon: Multi-mode limit cycle oscillations

This paper studies the application of mathematical models to analyze the vortex-induced vibrations of the tendons of a given TLP along the Indian coastline, by using an analytical approach, analyzed using MATLAB. The tendon is subjected to a steady current load, which causes vortex-shedding downstream, leading to cross-flow vibrations. The magnitude of the excitation (lift and drag coefficients) depends on the vortex-shedding frequency. The resulting vibration is studied for possible resonant behavior. The excitation force is quantified empirically, the added mass by potential flow hydrodynamics, and the vibration by normal mode summation method. Non-linear viscous damping of the water is considered. The non-linear oscillations are studied by the phase-plane method, investigating the limit-cycle oscillations. The stable/unstable regions of the dynamic behavior are demarcated. The modal contribution to the total deflection is studied to establish the possibility of resonance of one of the wet modes with the vortex-shedding frequency.     

Techno-economic study of LNG diesel power (dual fuel) ship

This article mainly proposed three technically effective alternatives to comply with the emission control regulations and laws in shipping. Liquefied natural gas (LNG)-diesel dual fuel power technology was introduced through feasibility study on several aspects including research development, retrofitting methods, vessel type, safety issues, and other technical characteristics. Based on sample ship and route, economic evaluation was conducted on these three alternatives. Cost-effectiveness of each project was detailed in the calculation of net present value (NPV) and payback time via discount cash flow method. The findings show that LNG-diesel dual fuel power technology performs best among three alternatives. Due to the impact of fuel price, two scenarios were carried out in sensitivity analysis which witnessed a variation of NPV with the fluctuation of fuel price. Further study shows the turning point between project (i) and project (iii) with different discount rate and the interaction between discount rate and fuel price, left project (ii) the least cost-effective solution in three alternatives.     

Evaluating air emission inventories and indicators from cruise vessels at ports

This paper provides an estimation of air emissions (CO₂, NO_X, SO_X and PM) released by cruise vessels at the port level. The methodology is based on the “full bottom-up” approach and starts by evaluating the fuel consumed by each vessel on the basis of its individual port activities (manoeuvring, berthing and hoteling). The Port of Barcelona was selected as the site at which to perform the analysis, in which 125 calls of 30 cruise vessels were monitored. Real-time data from the automatic identification system (AIS), factor emissions from engine certificates and vessel characteristics from IHS Sea-web database were also collected for the analysis. The research findings show that the most appropriate indicators are inventory emissions per “port-time gross tonnage”, “port-time passenger” and “port time”. These emission indicators improve our understanding of cruise emissions and will facilitate the work that aims to estimate reliably and quickly the in-port ship emission inventories of cruise ports.     

Workspace analysis to generate a collision-free torch path for a ship welding robot

We propose a method to determine the optimal initial location and to generate torch paths for a ship welding robot with 6 degrees of freedom (DOF). The optimal initial location is determined using an objective function, which is set up by combining constraints on the torch posture, manipulability, and the range of each joint angle to avoid collisions. A genetic algorithm (GA) is used to optimize the objective function because it does not require additional derivatives. After the initial location is determined, torch paths are generated by interpolating the starting point, endpoints and torch postures using inverse kinematics. Our method can be applied to automate the welding job for each block during ship building, irrespective of the shape of the robots, by changing the objective function.     

Unsteady finite-depth effects during resistance tests on a ship model in a towing tank

This paper covers an extension of the study of Doctors et al. (J Ship Res 52(4):263–273, 2008) on oscillations in wave resistance during the constant-velocity phase of a towing-tank resistance test on a ship model to the case of relatively shallow water. We demonstrate here that the unsteady effects are very prominent and that it is essentially impossible to achieve a steady-state resistance curve in a towing tank of typical proportions for a water-depth-to-model-length ratio of 0.25. This statement is particularly true in the speed region near a depth Froude number of unity. However, on the positive side, we show here that an application of unsteady linearized wave-resistance theory provides an excellent prediction of the measured total resistance, when one accounts for the form factor in the usual manner. Finally, a simple application of the results to the planning and analysis of towing-tank tests is presented.