Development of an electric active rollcontrol (ARC) algorithm for a SUV

Cornering maneuvers with reduced body roll and without loss in comfort are leading requirements for car manufacturers. An electric active roll control (ARC) system controls body roll angle with motor-driven actuators installed in the centers of the front and rear stabilizer bars. A vehicle analysis model developed using a CarSim S/W was validated using vehicle test data. Two ARC algorithms for a sports utility vehicle (SUV) were designed using a sliding-mode control algorithm based on a nonlinear roll model and an estimated lateral acceleration based on a linearized roll model. Co-simulation with the Matlab simulink controller model and the CarSim vehicle model were conducted to evaluate the performance of two ARC control algorithms. To validate the ARC performance in a real vehicle, vehicle tests were conducted at KATECH proving ground using a small SUV equipped with two ARC actuators, upper and lower controllers and a few subsystems. From the simulation and vehicle validation test results, the proposed ARC control algorithm for the developed ARC actuator prototypes improves the vehicle’s dynamic performance.     

A robust optimization for the frequency and decoupling ratio of a powertrain mounting system based on interval analysis

This paper presents a robust optimization method to decrease the variations in the performance of the designed system caused by the unavoidable manufacturing, installation or measurement errors of the design variables. Generally, it is difficult and costly to determine statistical information with sufficient precision for uncertain design variables; in this study, interval numbers are used to describe the uncertain design variables, and only the bounds of these variables are required. An improved interval truncation method is presented for estimating the variation ranges of the system performances. The robustness estimations of the system performances are incorporated into the optimization formulation to obtain the nominal design variables, which could make the system performances relatively robust; therefore, the design robustness is estimated and improved in the optimization iteration process. The robust optimization method is applied to a general powertrain mounting system (PMS) to improve the design robustness of the PMS decoupling layout and frequency allocation. The optimization results show that the robust optimization method could effectively increase the decoupling ratios in the interested vertical and pitch directions, and the frequency allocation is more robust than that obtained using the traditional deterministic optimization.     

Effect of the fuel injection strategy on first-cycle firing and combustion characteristics during cold start in a TSDI gasoline engine

The first firing cycle is very important during cold-start for all types of spark ignition engines. In addition, the combustion characteristics of the first firing cycle affect combustion and emissions in the following cycles. However, the first-cycle fuel-air mixing, combustion and emissions generation within the cylinder of a two-stage direct-injection (TSDI) engine during cold start is not completely understood. Based on the total stoichiometric air-fuel ratio and local richer mixture startup strategy, the first-cycle firing and combustion characteristic at cold start were investigated in a two-stage direct injection (TSDI) gasoline engine. In addition, the effects of the first injection timing, second injection timing, 1st and 2nd fuel injection proportion and total excess air ratio on the in-cylinder pressure, heat release rate and accumulated heat release were analyzed on the basis of a cycle-by-cycle analysis. It is shown that a larger 2nd fuel injection amount and later 2nd injection timing are more beneficial to the firing of the first cycle in the case of a total excess air ratio of 1.0. The optimum 1st and 2nd injection timing fuel injection proportions are 120°CA ATDC during the intake stroke, 60°CA BTDC during the compression stroke and 1:1. In addition, the firing boundary is a 2nd injection timing later than 90°CA BTDC during the compression stroke in the case of the 1st injection timing from 60°CA to 180°CA ATDC during an intake stroke and involves a 1st and 2nd fuel injection proportion of 1:1 and an excess air ratio of 1.0. The study provides a detailed understanding of cold-start combustion characteristics and a guide for optimizing the reliable first-cycle firing at cold start.     

New metal fitting geometry and optimization of the swaging parameters for an automobile power steering hose

To solve the power steering (PS) hose oil leakage problem in automobile applications, a new geometry design of the metal fitting is required, and the swaging conditions applied to the PS hose should be optimized. In this study, a new metal fitting geometry for the PS hose was proposed. A CAE simulation for both the proposed and the conventional metal fittings was conducted, and both the stress and the strain in the PS hose were compared. An experimental verification was also performed with these two different metal fittings. Additionally, the swaging conditions were optimized by the durability cycle time, which was measured in an impulse test of the swaged PS hose. For a more economical production, practical working conditions were also recommended and experimentally verified.     

Development of a new traction control system for vehicles with automatic transmissions

A traction control system (TCS) is used to improve the acceleration performance on slippery roads by preventing excessive wheel slip. In this paper, a new traction control system using the integrated control of gear shifting and throttle actuation is developed for vehicles with automatic transmissions. In the design of the slip controller, by means of a differential manifold transformation, a slip control system with nonlinearities and uncertainties is transformed into a linear system, and a sliding mode controller is applied for the purpose of increasing the robustness of the system. Next, to achieve the required driving torque, the optimal throttle and gear position, maps are constructed based on dynamic programming. The simulation results indicate that the present traction control system can improve the acceleration performance of an automatic transmission vehicle for various types of road conditions.     

Heat exchanger/catalytic system for reducing the exhaust emissions from diesel engines

A system has been researched over the past 3 years for reducing the exhaust pollutants from diesel engines for light commercial vehicles. The system researched achieves Euro 6 standards for reduction of polluting gases (CO, HC, PM, NO). It consists of 4 main sections: 1. A heater and heat exchanger (HE); 2. A CO/HC oxidising catalyst (D°C); 3. Pt catalyst on a diesel particulate filter (DPF); 4. A NO reducing reaction (SCR) within the DPF. The system operates as follows. The exhaust gas contains oxidising gases, namely both O₂ and NO₂. The levels of CO and HC are oxidised by O₂ to CO₂ for temperatures above 200°C. Carbon (PM) is oxidised to CO₂ by NO₂ but requires a temperature above 250°C. The operating exhaust temperature of 300°C is ideal for the removal of NO by using the Pt catalyst and the CO generated within the DPF. The heater is required to be able to raise the exhaust temperature at any time to 300°C in order to optimise the performance of the system, since diesel engine exhaust temperatures vary between 160°C (slow speeds) to 350°C (high speeds). Considerable heat is required (??3 kW) to maintain the exhaust gas for a 2l engine at 300°C for engine idle conditions. Therefore a heat exchanger is required to re-circulate the input heat and thereby reduce the maximum power consumption to a maximum of 500W over the engine full operating test cycle. This energy is supplied by the engine battery and alternator. Experimental results have been obtained for the exhaust from a Kubota diesel engine and the reductions in exhaust emissions of 83% (CO/ HC), 58% (NOx) and 99% (PM) were obtained. The PM was continuously cleaned so that there was no build up of back pressure.     

Road identification in monocular color images using random forest and color correlogram

This paper presents a system to identify road and non-road regions from monocular color images of paved and unpaved roads. Despite being a single object, the road in these images is subject to large changes in appearance due to environmental effects and track materials. This condition has challenged the practical application of road identification. The proposed system combines random forest with color correlogram to overcome such conditions and offers a classifier for road and non-road regions in traffic images. As a color feature, the color correlogram depicts the spatial correlation of color changes in an image. Using random forest, road identification is formulated as a learning paradigm. The combined effects of color correlograms and random forest create a robust system capable of identifying roads even in variable situations in real time. This combination is more effective than other combinations, such as a color histogram plus random forest, a color correlogram plus neural network, or a color histogram plus neural network.     

Development of a new analytical model for a railway vehicle equipped with independently rotating wheels

The urban tram introduced recently has a low-floor structure for the convenience of passengers getting on and off. To adjust the low-floor level and improve performance on curves, most low-floor trams have IRWs (independently rotating wheels) with no central axle between the two wheels. Eliminating the central axle, however, creates several inherent problems, such as insufficient guiding force and excessive wear. To analyze these problems, a new analytical model is described in this paper to describe the dynamic characteristics of IRWs more precisely. This analytical model is developed to consider the effects of longitudinal creep in particular, which have been ignored in conventional analytical models of IRWs. In addition, a running stability analysis based on the newly developed analytical model is conducted to compare the critical speeds of IRW-axle vehicles and rigid-axle vehicles. The dynamic characteristics of an initial disturbance are compared to verify that the analytical model is effective in expressing the dynamic characteristics of IRWs.     

Switch Panel wear loading – a parametric study regarding governing train operational factors

The acting forces and resulting material degradation at the running surfaces of wheels and rail are determined by vehicle, track, interface and operational characteristics. To effectively manage the experienced wear, plastic deformation and crack development at wheels and rail, the interaction between vehicle and track demands a system approach both in maintenance and in design. This requires insight into the impact of train operational parameters on rail- and wheel degradation, in particular at switches and crossings due to the complex dynamic behaviour of a railway vehicle at a turnout. A parametric study was carried out by means of vehicle-track simulations within the VAMPIRE® multibody simulation software, performing a sensitivity analysis regarding operational factors and their impact on expected switch panel wear loading. Additionally, theoretical concepts were cross-checked with operational practices by means of a case study in response to a dramatic change in lateral rail wear development at specific switches in Dutch track. Data from train operation, track maintenance and track inspection were analysed, providing further insight into the operational dependencies. From the simulations performed in this study, it was found that switch rail lateral wear loading at the diverging route of a 1:9 type turnout is significantly influenced by the level of wheel–rail friction and to a lesser extent by the direction of travel (facing or trailing). The influence of other investigated parameters, being vehicle speed, traction, gauge widening and track layout is found to be small. Findings from the case study further confirm the simulation outcome. This research clearly demonstrates the contribution flange lubrication can have in preventing abnormal lateral wear at locations where the wheel–rail interface is heavily loaded.     

Enhancement of aerodynamic performance through high pressure relief in the engine room for passenger car using cfd technique

High pressure acting on the vehicle’s body plays an important role in deciding the aerodynamic drag. An idea has been suggested to enhance the aerodynamic performance for small passenger car by relieving the high pressure in the engine room. The high pressure inside the engine room can be released to the outside of the vehicle through a hole perforated on the wheel house liner. About 1 % of the drag coefficient can be improved with the 1.88 % of the radiator air mass flow rate increment by installing the top hole with slots on the wheel house liner. Flow simulations are performed at the driving velocity of 110 km/h with the moving wall condition of the same velocity. The tire is rotating to catch more precise flow physics around a tire and wheelhouse liner.