Fine sediment deposits in shelf seas

From field observations it appears that the top layer of a shelf bottom in general exhibits an intricate geographical pattern of sediment formations. Sediments of different composition are confined in distinct regions. This contradicts the idea that current and wave forces stir up bottom sediment and disperse it in a random way over the shelf; the dispersal process is counteracted by sorting mechanisms. In this paper the bottom patterns of fine cohesive sediments are considered. A specific sorting mechanism is studied which may explain the patchy structure of fine sediment deposits. It is shown that fine sediments can be trapped in bottom deposits which contain a fine sediment fraction high enough to prevent pore water motion in the shelf bed. This mechanism opposes sediment dispersal away from existing deposits. It may also explain the formation or the preservation of mud patches, even in regions where the bottom shear stress is relatively high.     

Assimilation of sea surface temperature in the POL Coastal Ocean Modelling System

A one-dimensional scheme is used to assimilate satellite Sea Surface Temperature data into the Proudman Oceanographic Laboratory Coastal Ocean Modelling System, set up in the Irish Sea with a fine resolution ( 1.8 km). The capabilities of the assimilation scheme are investigated using two different sets of satellite data, of lower and similar resolution to that of the model respectively. Comparison of results with independent data show that assimilation improves the modelled Sea Surface Temperature, but does not address model representation of the temperature vertical structure. It is concluded that for the Irish Sea and at the scales resolved by the model, the assimilation problem cannot be approached in a one-dimensional framework. It is also pointed out that forecast error needs to account explicitly for errors in the representation of the vertical structure of the thermal field.Three-dimensional methods that are suited for coastal systems are then suggested.     

开口螺钉断裂的材料分析及工艺试验

制动夹钳单元中开口螺钉在高寒环境使用时发生断裂,对断裂的螺钉进行了断口分析,并对所使用2Cr13材料的热处理工艺进行了试验分析,检测不同温度下材料的冲击功,系统研究分析开口螺钉在低温下出现脆性断裂的原因并提出该零部件材料适用于低温的技术指标。     

Novel coordinated algorithm for Traction Control System on split friction and slope road

A Traction Control System (TCS) is used to avoid excessive wheel-slip via adjusting active brake pressure and engine torque when vehicle starts fiercely. The split friction and slope of the road are complicated conditions for TCS. Once operated under these conditions, the traction control performance of the vehicle might be deteriorated and the vehicle might lack drive capability or lose lateral stability, if the regulated active brake pressure and engine torque can’t match up promptly and effectively. In order to solve this problem, a novel coordinated algorithm for TCS is brought forward. Firstly, two brake controllers, including a basic controller based on the friction difference between the two drive wheels for compensating this difference and a fuzzy logic controller for assisting the engine torque controller to adjust wheel-slip, are presented for brake control together. And then two engine torque controllers, containing a basic PID controller for wheel-slip control and a fuzzy logic controller for compensating torque needed by the road slope, are built for engine torque control together. Due to the simultaneous and accurate coordination of the two regulated variables the controlled vehicle can start smoothly. The vehicle test and simulation results on various road conditions have testified that the proposed method is effective and robust.     

Vehicle Dynamics Estimation Using Kalman Filters

This paper deals with the application of stochastic state estimators in vehicle dynamics control. It is often unrealistic to assume that all vehicle states and the disturbances acting on it can be measured. System states that cannot be measured directly, can be estimated by a Kalman Filter. The idea of the Kalman filter is to implement a model of the real system in an on-board computer in parallel with the system itself. This paper will give 3 examples of this principle applied to automotive systems.     

Effects of split injection,oxygen enriched air and heavy EGR on soot emissions in a diesel engine

The effects of split injection, oxygen enriched air, and heavy exhaust gas recirculation (EGR) on soot emissions in a direct injection diesel engine were studied using the KIVA-3V code. When split injection is applied, the second injection of fuel into a cylinder results in two separate stoichiometric zones, which helps soot oxidation. As a result, soot emissions are decreased. When oxygen enriched air is applied together with split injection, a higher concentration of oxygen causes higher temperatures in the cylinder. The increase in temperature promotes the growth reaction of acetylene with soot. However, it does not improve acetylene formation during the second injection of fuel. As more acetylene is consumed in the growth reaction with soot, the concentration of acetylene in the cylinder is decreased, which leads to a decrease in soot formation and thus soot emissions. A combination of split injection, a high concentration of oxygen, and a high EGR ratio shows the best results in terms of diesel emissions. In this paper, the split injection scheme of 75.8.25, in which 75% of total fuel is injected in the first pulse, followed by 8°CA of dwell time, and 25% of fuel is injected in the second pulse, with an oxygen concentration of 23% in volume and an EGR ratio of 30% shows a 45% reduction in soot emissions, with the same NOx emissions as in single injection.     

Application of Optimal Control Theory to Inverse Simulation of Car Handling

The application of Optimal Control Theory to time-optimal inverse simulation of car handling was investigated. Time-optimal inverse simulation of car handling involves the calculation of driver actions required to perform specified manoeuvres, in as short a time as possible. Driver actions consist of time-histories of front wheel steer rate and longitudinal force. Optimal time-histories of these quantities were calculated using the Gradient method after formulating the problem as one of optimal control. Simulation results are presented for two different cars performing similar lane-changes. These results show significant differences in necessary driver actions for different cars and demonstrate the suitability of the approach taken.     

On the capacity of isolated, curbside bus stops

The maximal rates that buses can discharge from bus stops are examined. Models were developed to estimate these capacities for curbside stops that are isolated from the effects of traffic signals. The models account for key features of the stops, including their target service levels assigned to them by a transit agency. Among other things, the models predict that adding bus berths to a stop can sometimes return disproportionally high gains in capacity. This and other of our findings are at odds with information furnished in professional handbooks.     

Influence of the residential and work environment on car use in dual-earner households

This paper analyses whether the decision to commute by car is influenced by built environment characteristics of residential neighbourhoods and, more especially, of work locations, taking into account interdependencies between household partners. It shows that the residential environment only affects car use among single-earners. Conversely, for all commuters, but in particular for dual-earners, characteristics of the work location affect whether they commute by car. Even in dual-earner households with two cars, work environment plays a role. We found that in cases of dual-earners with only one car, the partners with the longest commuting distances and the lowest density work locations are most likely to commute by car. Moreover, in households with young children, men are more inclined to leave the car at home. Other features relating to work also affect car commuting, including work flexibility and, especially, possession of a company car. We conclude that future policies aimed at reducing car use should place greater focus on work factors.     

Trip misreporting forecast using count data model in a GPS enhanced travel survey

As Global Positioning System (GPS) technology advances, it has been increasingly used to supplement traditional self-reported travel surveys due to its promising features in capturing travel data with better accuracy and reliability. Realizing the limitations of diary-based surveys, this paper presents a study that directly accounts for trip misreporting behavior in trip generation models. Travel data were obtained from prompted-recall assisted GPS survey along with a diary-based survey. Negative Binomial models for count data were developed to accommodate misreporting behavior by introducing interaction effects of the sample-indicator variable with various personal and household variables. The interaction effects indicate how the impacts of the socioeconomic and demographic variables on trip-making vary across the two samples. Assuming that the GPS sample represents the ground truth, the interaction effects actually capture the likelihood and the extent of trip misreporting by detailed personal and household characteristics. The model results reveal significant interaction effects of several personal and household variables, indicating misreporting behavior associated with these attributes. The addition of interaction coefficients to the main effect model represents the real impacts of the independent variables, after compensating for trip misreporting behavior, if any.