铁道车辆称重均衡试验台设计

介绍了新型铁道车辆称重均衡试验台的设计思路及结构组成。该试验台可实现铁道车辆多种车型的称重、均衡及柔性试验。     

车轮磨耗仿真中踏面更新策略研究

基于车辆系统动力学仿真和Braghin踏面磨耗模型计算车轮踏面上的磨耗深度分布,并采用小波滤波、滑动平均和傅里叶变换平滑3种方法对踏面磨耗深度曲线进行平滑。结果表明,小波滤波的平滑效果优于滑动平均和傅里叶变换平滑方法;更新磨耗深度越大,对磨耗行为和轮轨几何接触关系影响越大。因此,建议在最大磨耗深度达到0.1 mm时对仿真计算用的车轮型面进行更新。     

Deep foundation pit excavation procedure optimization considering creep deformation on nearby metro tunnelEI北大核心

Research purposes: The existing researches about excavating procedures of deep foundation pit on nearby metro tunnel in soft formation are lack of systematicness, and creep characteristics of soft clay are not usually taken into consideration. This paper takes Qianhaiwan station of Metro Line 11 in Shengzhen as engineering background and considers creep characteristics in sludge formation. The influence of step excavation in the transversal, longitudinal and vertical directions on the deformation of foundation pit and nearby subway tunnel are simulated, which may be expected to provide theoretical basis for choosing foundation pit excavation procedure of Qianhaiwan station. Research conclusions: (1) The segment far away from tunnel should be excavated firstly when only transversal step excavation was undertaken along the horizontal direction of foundation pit. (2) The maximum horizontal displacement of the piles show exponential relations with the number of segments when step excavation of foundation pit was undertaken in vertical and transversal or longitudinal. If thickness of every step excavation was limited in 1.5~2 m, the horizontal displacement of the pile near tunnel can be reduced about 9 percent when there is no horizontal step excavation. (3) Transversal step excavation with segments far from tunnel excavated firstly was found to be the best step excavation method under the same condition of step number and support, and longitudinal and transversal step excavation followed while longitudinal step excavation was the last. (4) The research results have guiding significance for foundation pit of Qianhaiwan station and similar projects.     

出口苏丹米轨平车研制

介绍了出口苏丹米轨平车的技术参数、结构特点和试制情况。     

货车焊接结构疲劳寿命预测研究

基于国际焊接学会标准和英国标准,结合有限元静强度结果和实测载荷谱,对某出口运煤车车体关键部位典型焊接接头形式进行了疲劳寿命对比分析。结果表明,合理选择焊接接头形式和焊接工艺可以成倍地提高结构的疲劳寿命。     

Quantifying travel time variability at a single bottleneck based on stochastic capacity and demand distributions

Travel time reliability, an essential factor in traveler route and departure time decisions, serves as an important quality of service measure for dynamic transportation systems. This article investigates a fundamental problem of quantifying travel time variability from its root sources: stochastic capacity and demand variations that follow commonly used log-normal distributions. A volume-to-capacity ratio-based travel time function and a point queue model are used to demonstrate how day-to-day travel time variability can be explained from the underlying demand and capacity variations. One important finding is that closed-form solutions can be derived to formulate travel time variations as a function of random demand/capacity distributions, but there are certain cases in which a closed-form expression does not exist and numerical approximation methods are required. This article also uses probabilistic capacity reduction information to estimate time-dependent travel time variability distributions under conditions of non-recurring traffic congestion. The proposed models provide theoretically rigorous and practically useful tools for understanding the causes of travel time unreliability and evaluating the system-wide benefit of reducing demand and capacity variability.     

Development of a low-noise cooling fan for an alternator using numerical and doe methods

An alternator, which converts mechanical rotational energy into electrical energy, is an important component of a vehicle. Alternators operate over a broad range of rotational speeds, typically from 3,000 RPM to 18,000 RPM, which demands a cooling fan producing sufficient airflow, ideally with a minimum of noise. In the current study, an optimized alternator-cooling fan was developed through a linked DOE(Design OF Experiment) process and numerical analysis. The SC/Tetra and FlowNoise S/W programs were used to calculate flow rates and noise levels, respectively, for the newly developed fan. Compared with original model, the numerical results predicted a 3 dBA noise reduction; the measured reduction was 4 dBA.     

Model-based design of a variable nozzle turbocharger controller

Variable Nozzle Turbocharger (VNT) was invented to solve the problem of matching an ordinary turbocharger with an engine. VNT can harness exhaust energy more efficiently, enhance intake airflow response and reduce engine emissions, especially during transient operating conditions. The difficulty of VNT control lies in how to regulate the position of the nozzle at different engine working conditions. The control strategy designed in this study is a combination of a closed-loop feedback controller and an open-loop feed-forward controller. The gain-scheduled proportional-integral-derivative (PID) controller was implemented as the feedback controller to overcome the nonlinear characteristic. As it is difficult to tune the parameters of the gain-scheduled PID controller on an engine test bench, system identification was used to identify the plant model properties at different working points for a WP10 diesel engine on the test bench. The PID controller parameters were calculated based on the identified first-order-plus-dead-time (FOPDT) plant model. The joint simulation of the controller and the plant model was performed in Matlab/Simulink. The time-domain and frequency-domain performances of the entire system were evaluated. The designed VNT control system was verified with engine tests. The results indicated that the real boosting pressure traced the target boosting pressure well at different working conditions.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.