城市立交桥连续箱梁静载试验

结合青岛市一立交桥连续箱梁工程实例,运用荷载试验与结构分析方法,分析了连续箱梁桥在设计荷载作用下的承载能力、挠度特性和应变特性。试验分析表明,在设计荷载作用下箱型梁桥的强度、刚度满足设计要求。     

某曲线梁桥出现平面转动位移的原因分析及处理措施

结合工程实例,分析混凝土曲线连续梁桥出现梁体平面转动位移的原因,介绍采用梁体顶升纠扭,同时对远端支座增设横向限位,以使梁体恢复到设计状态的具体措施。     

现代注浆技术的开拓应用及发展

文章介绍了目前已经出现的几种注浆法开拓应用的新技术,如锚注支护、爆破注浆、立井"三同时"施工工艺、电化学注浆等;提出了"抽注式"注浆、磁化水注浆、注浆拔孔桩等一些新的注浆技术开发思路;并指出今后应加强制定注浆技术规范、试验标准、预算定额、研制注浆试验仪器、加大注浆理论与技术研究力度.     

高烈度地震区公路隧道洞口段地震响应分析

根据隧道地震安全性评价报告和地勘资料,建立了三维数值计算模型并采用一致粘弹性人工边界模拟动力边界,对高烈度地震区公路隧道洞口段进行了瞬态动力计算。计算结果表明:在三向地震荷载激励下,洞口段衬砌的地震响应具有明显滞后性,衬砌以水平横向振动为主、轴向振动次之、竖向振动最弱;洞口段衬砌的拱腰部位将承受极大拉应力和剪应力,可设减震层吸收地震能量。通过对衬砌相对位移的分析得出,衬砌横向和轴向变形都很小,衬砌稳定性尚好。     

A new channel allocation scheme for hierarchical wireless networks

A channel allocation scheme for hierarchical wireless networks was proposed in terms of the connection-level quality of service. The channel allocation scheme was analyzed using both horizontal channel borrowing and vertical traffic overflowing. Pre-emptive priority strategies are used to classify real-time services and non-real-time services, real-time service is given higher priority for it is allowed to pre-empt channels used by non-real-time service. Some channel borrowing thresholds and acceptance ratios are used to avoid channel locking or dynamic power control, which can also be dynamically adjusted according to network load. Simula-tion results show that the proposed schemes can improve the system performance.     

Reliability analysis of repairable systems using stochastic point processes

In order to analyze the failure data from repairable systems, the homogeneous Poisson process(HPP) is usually used. In general, HPP cannot be applied to analyze the entire life cycle of a complex, re-pairable system because the rate of occurrence of failures (ROCOF) of the system changes over time rather thanremains stable. However, from a practical point of view, it is always preferred to apply the simplest methodto address problems and to obtain useful practical results. Therefore, we attempted to use the HPP model toanalyze the failure data from real repairable systems. A graphic method and the Laplace test were also usedin the analysis. Results of numerical applications show that the HPP model may be a useful tool for the entirelife cycle of repairable systems.     

物流企业联盟利益分配方法研究

分析了物流企业联盟利益分配的原则,提出了几种常用的利益分配方法,并在此基础上进行改进,提出了基于加权群体重心模型的利益分配方法,实例证明该方法更加具有公平合理性,在物流企业联盟的利益分配中有应用推广价值。     

边坡防护室内水力冲刷模拟试验及降雨入渗分析

阐述了边坡防护室内水力冲刷模拟试验的目的、方法和步骤.针对不同边坡防护型式、不同坡率、不同土质状况的五种试件进行了降雨入渗试验,对结果进行了分析,并总结出不同工况下的降雨入渗规律.     

Numerical Analysis of the Mixture Formation in a Two-Stroke Wall-Guided LPG DI Engine for Extended-Range Electric Vehicle

The use of automotive LPG characteristics which are easy to evaporate vaporization and carry. The paper presents a design of extended-range electric vehicle for wall-guided two stroke LPG engine with direct injection combustion system. Based on the modified vehicle LPG spray model, a database describing the characteristics of vehicle LPG fuel was built and imported into the CFD software. And the accuracy of the model is verified by the Schlieren experimental results. The concentration and velocity field of the mixture in the cylinder under different load conditions are numerically analyzed. The analyzed result indicated that the start injection time θ = 60°–70°CA BTDC under part load condition, the plug electrode near the gathering of a richer mixture is easy to be fired at spark ignition time, the obvious formation of mixture in cylinder is formed and the overall air-fuel ratio is above 40: 1. The start-transition working condition and large load conditions in the piston moves upward before closing the exhaust port to start injection LPG. The optimized LPG injection start time θ ensures that the fresh gas is locked in the cylinder when the exhaust port is closed (63°CA ABDC). In the ignition time of the spark plug, an ideal homogeneous mixture in the cylinder is realized.     

某轿车副车架模态分析

本文通过用Hypemesh11.0进行网格划分,然后用MSC.NASTRAN进对某轿车副车架进行模态分析,以确定冲压横梁结构是否能够达到原液压横梁结构的模态固有频率,为制定工艺方案提供支持,也为以后同类产品的研发提供设计参考。