柴油机典型工况的电控喷油器多次喷射分配

为提高柴油机节能减排的效果,简要分析了多次喷射形式及其作用,依据车辆在不同路况运行,确定了车辆对应的6种柴油机典型工况。提出了基于工况排放值约束的多次喷射分配方法,采用工况排放分摊率确定典型工况的排放限值,进行喷射次数和变化喷射组合寻优,最后结合4JB1高压共轨柴油机台架试验,以氮氧化物和烟度为衡量参数,兼顾燃油消耗率的变化,分析不同喷射组合对柴油机排放的影响。结果表明:怠速工况和中速大负荷工况宜用2次喷射,低速小负荷工况和中速中负荷工况宜用3次喷射,中速小负荷工况宜用4次喷射,高速大负荷工况宜用1次喷射,说明基于工况排放值约束的多次喷射分配方法是有效的。     

农用车辆配套简易播种机设计

文章介绍的旋耕播种机主要由六个部分组成,即:悬挂装置、动力传输装置、旋耕装置、播种装置、镇压装置和链条传动装置。农用车辆拖拉机前进后镇压装置也向前运行带动链条传动装置,与之另一端连接的播种箱的播种轴也随之转动,使种子从排种孔中流出顺着播种管与播种开沟器流出最后流入垄沟,从而实现播种机的播种作业。播种机播种后的农作物生长均匀分布排列整齐,这样可以便于人们实现播种过后对田地的管理作业,也是人们实现农业机械现代化的重要技术手段之一。     

纯电动卡车总装混线生产的工艺研究

纯电动卡车的产品特点与传统燃油卡车既有共性又存在差异,对比两种车型的底盘装配和调试工艺后,在传统燃油车总装配线的基础上设计了一套新能源的装配工艺流程,不仅提高总装配车间柔性化生产,还实现了纯电动卡车和燃油卡车的混线生产。     

高速公路隧道突发事件应急管理研究

高速公路隧道应急管理研究目的在于完善隧道应急管理体制,在应急救援过程中提高应急救援效率,尽可能的减少人民群众生命财产损失。文章分析了应急管理体系、应急预案、应急演练以及应急新闻发布方面存在的问题,并提出灵活组合使用四种应急处置机制、加强应急救援演练等建议。     

市政给中水管道设计优化分析

市政给排水管道结构设计是一项关乎管道安全的重要设计,设计人员往往根据以往经验和常规做法进行管道设计,忽略了管道安全计算,这将直接影响城市市政道路给排水管道工程的质量。结合实际项目,对给水、中水管道的常规管材球墨铸铁管进行结构计算分析,并根据计算结果选择相应的措施,进一步完善市政管道设计,在满足设计规划、规范和要求的基础上,提高设计质量,确保城市道路市政给排水管道正常、高效地运行。     

综合交通枢纽车道边交通组织方式研究

针对现代综合交通枢纽车道边的交通组织方式进行研究,结合车站的整体建筑布局、周边路网、交通量等提出了简单、实用和高效的交通组织方式。     

Virtual prototype simulation on underwater hydraulic impingement shovel

The virtual prototype technology is applied to the design of the hydraulic impingement shovel, which is to increase the reliability of the design. The work principle of hydraulic impingement shovel is expatiated, and its dynamic equations are established. The 3D model of virtual prototype is built by PRO/E. Then the couple between the mechanical body of prototype and the hydraulic system is completed by virtue of ADAMS. Finally, the simulation is made on the virtual prototype. The simulation results show that the design of underwater hydraulic impingement shovel is rational. The virtual prototype technology could lay sound foundation of successful manufacturing of physical prototype for the first time and offer highly effective and feasible means for the design and production of underwater equipments.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

Using a SVM to evaluate damage to vibration isolators in an elastic raft system

Predicting damage to vibration isolators in a raft experiencing heavy shock loadings from explosions is an important task when designing a raft system. It is also vital to be able to research the vulnerability of heavily shocked floating rafts unreliable, especially when the allowable values The conventional approach to prediction has been or ultimate values of vibration isolators of supposedly uniform standard in a raft actually have differing and uncertain values due to defective workmanship. A new model for predicting damage to vibration isolators in a shocked floating raft system is presented in this paper. It is based on a support vector machine（SVM）, which uses Artificial Intelligence to characterize complicated nonlinear mapping between the impacting environment and damage to the vibration isolators. The effectiveness of the new method for predicting damage was illustrated by numerical simulations, and shown to be effective when relevant parameters of the model were chosen reasonably. The effect determining parameters, including kernel function and penalty factors, has on prediction results is also discussed. It can be concluded that the SVM will probably become a valid tool to study damage or vulnerability in a shocked raft system.