Experimental investigation of B20 combustion and emissions under various intake conditions for low-temperature combustion

Recently, biodiesel has emerged as an alternative fuel for achieving low-temperature combustion (LTC). Several articles in the literature have showed that oxygenated biofuels, including biodiesel, can improve combustion stability under high exhaust gas recirculation (EGR) operation, which is considered to be necessary for the removal of nitric oxides (NOx). The objective of this study was to investigate the performance and emissions of 20% biodiesel blended diesel fuel (B20) at various intake pressures and oxygen concentration levels to characterize the fuel for LTC application. The experimental investigation of B20 was carried out using a single-cylinder engine (SCE) at 1400 rpm and 50% load condition. A set of critical flow orifices with synthetic EGR was employed to simulate various intake pressures and EGR levels. The behavior of the B20 was first characterized under various intake conditions. The results showed that with high oxygen intake, B20 exhibited combustion and emission levels that were very similar to conventional diesel. However, B20 reduced combustion deterioration while exhibiting lower carbon monoxide (CO) and hydrocarbon (HC) emissions than diesel under low oxygen intake conditions.     

Analysis of the effect of cold start on fuel economy of gasoline automatic transmission vehicle

FTP75 driving cycle is used in many countries for evaluation of vehicle fuel economy. FTP75 has 3 phases, where the Phase 1 and the Phase 3 have a same velocity profile, but the Phase1, which is known as cold start phase, shows lower fuel efficiency than the Phase 3. In order to analyze the difference of fuel economy between Phase 1 and Phase 3, vehicle tests are performed. The test results show that the differences of fuel economy is ranging from 3.9% to 18.5%. The factors of the difference of fuel economy for gasoline automatic transmission vehicles are analyzed in this research. The key factors affecting the difference of fuel economy are engine friction loss, torque converter loss and accessory loss. The quantitative analysis of these factors is performed.     

浮体横摇运动传递函数数学建模的频域分析研究及相关数值验证(英文)

This paper investigates mathematical modelling of response amplitude operator(RAO) or transfer function using the frequency-based analysis for uncoupled roll motion of a floating body under the influence of small amplitude regular waves. The hydrodynamic coefficients are computed using strip theory formulation by integrating over the length of the floating body. Considering sinusoidal wave with frequency( ω) varying between 0.3 rad/s and 1.2 rad/s acts on beam to the floating body for zero forward speed, analytical expressions of RAO in frequency domain is obtained. Using the normalization procedure and frequency based analysis, group based classifications are obtained and accordingly governing equations are formulated for each case. After applying the fourth order Runge-Kutta method numerical solutions are obtained and relative importance of the hydrodynamic coefficients is analyzed. To illustrate the roll amplitude effects numerical experiments have been carried out for a Panamax container ship under the action of sinusoidal wave with a fixed wave height. The effect of viscous damping on RAO is evaluated and the model is validated using convergence, consistency and stability analysis. This modelling approach could be useful to model floating body dynamics for higher degrees of freedom and to validate the result.     

Discussion on the assessment of initial stress field of railway rock massEI北大核心

Research purposes: In actual work, according to the ground stress data for assessment, most railway tunnels are under very high ground stress and high ground stress state, which causes adjustment of surrounding rock and engineering measures to strengthen, thus these will cause large increased investment, even cause large dispute and chaos in analysis causes of tunnel lining cracking and deformation, but the engineering case that rock burst and large deformation occurred in actual excavation of tunnel is very rare. In this paper, according to rock mass mechanical theory, the ground stress information and engineering case, combined the relevant provisions of similar industry, the assessment of initial stress fields of rock mass in railway specification is discussed. Research conclusions: (1) The assessment of railway specification to initial ground stress field is not realistic and should be revised, preliminary judgment when the measured in-situ stress >30 MPa, the possibility of rockburst is increased. (2) Assessment conclusion of initial ground stress field should be discreet, the increased investment should be incorporated into the dynamic design. (3) The stress tests of survey design stage should be reasonable and appropriate. (4) The research results can be applied to the modification of railway norms and tunnel exploration.     

A network equilibrium approach for modelling activity-travel pattern scheduling problems in multi-modal transit networks with uncertainty

An understanding of the interaction between individuals’ activities and travel choice behaviour plays an important role in long-term transit service planning. In this paper, an activity-based network equilibrium model for scheduling daily activity-travel patterns (DATPs) in multi-modal transit networks under uncertainty is presented. In the proposed model, the DATP choice problem is transformed into a static traffic assignment problem by constructing a new super-network platform. With the use of the new super-network platform, individuals’ activity and travel choices such as time and space coordination, activity location, activity sequence and duration, and route/mode choices, can be simultaneously considered. In order to capture the stochastic characteristics of different activities, activity utilities are assumed in this study to be time-dependent and stochastic in relation to the activity types. A concept of DATP budget utility is proposed for modelling the uncertainty of activity utility. An efficient solution algorithm without prior enumeration of DATPs is developed for solving the DATP scheduling problem in multi-modal transit networks. Numerical examples are used to illustrate the application of the proposed model and the solution algorithm.     

Dynamic system‐optimal traffic assignment for a city using the continuum modeling approach

This paper presents a continuum dynamic traffic assignment model for a city in which the total cost of the traffic system is minimized: the travelers in the system are organized to choose the route to their destinations that minimizes the total cost of the system. Combined with the objective function, which defines the total cost and constraints such as certain physical and boundary conditions, a continuum model can be formulated as an optimization scheme with a feasible region in the function space. To obtain an admissible locally optimal solution to this problem, we first reformulate the optimization in discrete form and then introduce a heuristic method to solve it. This method converges rapidly with attractive computational cost. Numerical examples are used to demonstrate the effectiveness of the method. Copyright © 2013 John Wiley & Sons, Ltd.     

Vibration path analysis and optimal design of the suspension for brake judder reduction

Brake judder is abnormal vibration, which is mainly generated by uneven contact between the brake disc and pad. The abnormal vibration from BTV (Brake Torque Variation) is transferred to the suspension and the steering system during braking. In this paper, judder simulation is carried out using a multi-body dynamic analysis program to analyze the relationship between judder and the transfer mechanism, which consists of the suspension and the steering system. In order to verify the analytical model, test results are compared with the simulation results. A sensitivity analysis is also carried out. In addition, an optimization method is presented for judder reduction, using the design of experiments.     

Improved hot-stamping analysis of tubular boron steel with direct measurement of heat convection coefficient

There are two types of hot-stamping processes, direct and indirect, depending on the sequence of the heating, forming, and quenching steps and the method used for each step. In this study, an indirect hot-stamping process consisting of forming at room temperature, heating, and water quenching was applied to develop a coupled torsion beam axle. The analysis results indicated that the application of the heat convection coefficient is critical in the simulations and must take into account the temperature and specific location in the model to ensure the accuracy of the heating and quenching analysis. The heat convection coefficients used in the analysis were directly measured at various positions of the tube (e.g., outside, inside, and bending region) using thermocouples, and the final values were determined through correlation between the actual tests and numerical analysis. The experimental and simulated final deformed shape and temperature distribution were in good agreement.     

Fatigue life estimation of injection mold core using simulation-based approach

The purpose of this study is to present a simulation-based approach capable of predicting the fatigue life of a mold core with the help of CAE technology based on injection molding simulation, core stress analysis and fatigue life prediction. Injection molding simulation is performed in order to obtain the non-uniform pressure acting on a mold core due to the polymer melt flow during injection molding process. Subsequently, the melt pressure profile is used as loading condition for core stress analysis via one-way coupling technique. The lifetime of a mold core is then predicted by fatigue analysis with stress-life approach. For verification of simulation-based approach to the fatigue life prediction, tests were also performed.     

Development of estimation algorithms for vehicle’s mass and road grade

In controlling the longitudinal motion of electrified vehicles such as hybrid vehicles and PHEV (Plug-in Hybrid Electric Vehicles), the variation of the driving resistance loads (or driving loads) such as road grade and actual vehicle mass, is the most influential factor which limits the control performance. Measuring the driving load is not impossible, but it is costly since additional sensors have to be mounted on the vehicle. In this study, methods for estimating vehicle mass and road grade are designed to compensate for the driving loads. The proposed methods are verified using simulation tools and then evaluated experimentally.