Transit assignment under crowded conditions

This paper presents a transit assignment algorithm for crowded networks. Both congestion in vehicles and queuing at stations are explicitly taken into account in predicting passenger flows for a fixed pattern of origin-destination trip demands. The overflow effects due to insufficient capacity of transit lines are considered to be concentrated at transit stations, while the in-vehicle congestion effects (or discomforts) are considered to be dependent on in-vehicle passenger volume. Overflow delay at a transit station is dependent on the number of excess passengers required to wait for the next transit car. We use a logit model to determine the split between passengers that chose to wait for the next transit car and passengers that chose to board on the alternative transit lines. The proposed algorithm predicts how passenger will choose their optimal routes under both queuing and crowded conditions.     

A study of passenger discomfort measures at the Hong Kong mass transit railway system

This note investigates the important attributes relating to the crowding effects at the Mass Transit Railway (MTR) stations in Hong Kong. Data was collected at two sets of three MTR stations to study the responses of the passengers due to the discomfort at crowded vehicles and platforms. Stated preference surveys were used to study the effects of passenger discomfort measures.     

Analysis of Driver's Decelerating Strategy in a Car-following Situation

This report describes a decelerating driver-model expressed by driving mode transition in car-following situations. The assumptions for constructing the model are that decelerating strategy of a driver is classified into several simple driving modes and that a driver changs his driving modes based on his perceptible characteristics and experiential rules. Deceleration action is divided into three states; following, standing and braking, which are applied to the model. The model has two paths for driver's decelerating action, one of which is selected by the driver based on the perceptible characteristics and experiential rules. The suitability of the model has been experimentally verified.     

Driver requirements and road traffic informatics

Initially the driver's role as a link in the driver-vehicle-road-traffic control-chain is discussed in a historical perspective. The gradual changes and the advantages and problems arising from these changes are discussed from behavioural point of view.Then the driver tasks are analyzed. A separation is made between trip planning, navigation, road following, traffic interaction, rule compliance, other than traffic tasks, car handling and speed choice. The relations between and the weights of these subtasks are discussed. Some existing driver behaviour models are reviewed in relation to the above mentioned tasks.Finally an effort is made based on the analyses of driver tasks and driver models to specify some general and some more specific potential advantages and problems with expected future RTI-systems.     

The design of bus route systems — An interactive location-allocation approach

An interactive modelling approach is developed to solve the practical problem of bus route network design. Possible bus routes are identified with facilities which can be located. Zones or pairs of zones in the urban area are identified with customers who will be allocated to the established facilities. It is shown that the classical Set Covering Problem is useful under the assumption of fixed demand; the Simple Plant Location Problem is effective under the assumption of demand which is sensitive to the level of bus service provided.     

A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

Determinants of the property damage costs of bulk barge accidents

This study investigates determinants of the vessel, cargo, and other-property damage costs of bulk barge accidents in US inland waterways. Tobit estimation of a three-equation recursive model suggests that, in bulk barge accidents: (1) vessel damage cost is greater for collision, fire/explosion, and material/equipment failure accidents than for groundings; (2) cargo damage cost is greater at night and when the weather is foggy and increases with barge age; and (3) otherproperty damage cost is greater for multi-vessel accidents, but decreases with barge size. A dollar of vessel damage cost increases other-property damage cost by $1.38, while a dollar of cargo damage cost increases this cost by $6.90. An important result for formulating bulk barge accident cost-reduction policies is that a given determinant might have a negative effect on one type of damage cost but a positive effect on another.     

台北公共交通月及无车日活动回顾与展望

台北国际无车日自2002年起举办了5次,由最早的骑自行车活动扩大至包含“走路上学日”与“公共交通月”丰富多彩的系列活动,渐渐获得民众认同。无车日活动的目标是通过活动的倡导和社会参与来改变民众使用交通工具的行为,潜移默化的效应可促使形成可持续交通政策,当可持续交通政策与基础设施建设落实后又可具体改变交通环境,形成良性的循环机制。首先说明了“无车日”的由来,并回顾台北都会区过去5年来举行无车日系列活动的内容与经验,同时基于活动的发展与成果归纳出无车日活动的成功要素,最后提出未来活动将扩大举办的内容、方式与展望,以期能为其他城市作参考。     

Experimental Study on Mechanical Behaviors of Prefabricated Column-Base Joint with Grouted Sleeves Connecting Longitudinal Reinforcements in Tunnels北大核心CSCD

In recent years, large shield tunnels with internal double-decked lanes have been developing rapidly in the field of highway tunnels, and prefabricated elements are increasingly adopted in internal structure. Based on the columns-base joint in Zhuguanglu tunnel, which is under construction, 2 full-scale specimens are designed for the quasi-static test, one specimen is connected with grout sleeve splicing and the other is cast in place. The test results show that: the bearing capacity of specimen with grout sleeve splicing is equal to that of cast-in-situ specimen, but its ductility and energy dissipation capacity are worse than that of the cast-in-situ specimen. And for the specimen with grout sleeve splicing, there exists crack concentration on the area above the sleeve. The crack width is too larger in this area. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Vulnerability analysis for large-scale and congested road networks with demand uncertainty

To assess the vulnerability of congested road networks, the commonly used full network scan approach is to evaluate all possible scenarios of link closure using a form of traffic assignment. This approach can be computationally burdensome and may not be viable for identifying the most critical links in large-scale networks. In this study, an “impact area” vulnerability analysis approach is proposed to evaluate the consequences of a link closure within its impact area instead of the whole network. The proposed approach can significantly reduce the search space for determining the most critical links in large-scale networks. In addition, a new vulnerability index is introduced to examine properly the consequences of a link closure. The effects of demand uncertainty and heterogeneous travellers’ risk-taking behaviour are explicitly considered. Numerical results for two different road networks show that in practice the proposed approach is more efficient than traditional full scan approach for identifying the same set of critical links. Numerical results also demonstrate that both stochastic demand and travellers’ risk-taking behaviour have significant impacts on network vulnerability analysis, especially under high network congestion and large demand variations. Ignoring their impacts can underestimate the consequences of link closures and misidentify the most critical links.