应重视军民通用型舰船开发及应用技术研究

从和平时期军用舰船的有效利用和战时舰船的大量消耗，以及如何降低舰船的建造费用、如何减少舰船现代化改装时的难度和费用及民用船只的征用等多方面论述了开展“军民通用型舰船开发及应用技术研究”的重要意义，并针对军民通用型舰船研究提出了建议和看法。     

陕县涧里水库大坝结构稳定分析

本文主要从水库大坝的结构安全出发,依据有关现行规范规定和大坝安全评价分类标准,对涧里水库大坝上、下游抗滑稳定性和结构安全性进行了综合评价。根据目前工程现状,涧里水库大坝上、下游坝坡抗滑稳定性整体上均满足规范要求,但是,溢洪道未按设计要求完成,溢洪道右岸0 110～0 132段挡水墙高度不够,结构单薄,不满足抗倾稳定要求,且防浪墙、放水管裂缝影响坝体结构完整性。因此,涧里水库大坝结构稳定性为C级。     

公路建设项目法人激励模型研究

项目法人在公路项目建设中起着举足轻重的作用 ,其经营水平、工作绩效的高低直接关系到项目建设期三大控制目标的实现和企业的长远发展。利用委托～代理激励理论研究了项目法人制下的项目经营者激励模型 ,以期促进和完善现代项目企业制度 ,提高项目经营者自身及企业经济效益水平。     

Estimation of value of travel time reliability

In mode choice decision, travelers consider not only travel time but also reliability of its modes. In this paper, reliability was expressed in terms of standard deviation and maximum delay that were measured based on triangular distribution. In order to estimate value of time and value of reliability, the Multinomial and Nested Logit models were used. The analysis results revealed that reliability is an important factor affecting mode choice decisions. Elasticity is used to estimate the impacts of the different policies and system improvements for water transportation mode. Among these policies, decision maker can assess and select the best alternative by doing the benefit and cost analysis based on a new market share, the value of time, and the value of reliability. Finally, a set of promising policies and system improvement of the water transportation were proposed.     

A review of the Effect of α/W ratio on fracture toughness （Ⅱ） experimental investigation in LEFM

In part I of this series, experimental investigation in EPFM （elastic-plastic fracture mechanics） had been discussed. In this paper, experimental investigation in LEFM （ linear elastic fracture mechanics） is given. Fracture toughness tests had been carried out on three different strength steels, using both through-cracked specimens with different α/W ratio and semi-elliptical cracked specimens with variable crack size and shape. Results show that the fracture toughness KIC increases with decreasing α/W when α/W 〈 0.3 for three-point-bend specimens, and that for α/W 〉 0.3, it is independent of α/W. Shallow crack specimens, both through-cracked and surface-cracked, gave markedly higher values than deeply notched specimens. However, the effect of crack shape on fracture toughness is negligible. Results also show that the LEFM approach to fracture is not tenable for design stresses where αc is often very small, far less than 2.5 （ KIC/σy）^2.     

TDCS/CTC中心网络安全防护系统的补强方案

针对目前铁路局TDCS/CTC中心网络安全设备存在的问题,按现行技术标准要求提出补强方案,并阐述了方案的思路、结构、取得的效果以及技术特点。     

Micro-Grinding Performance of Hard-Brittle Chip Materials in Precision Micro-Grinding Microgroove

The micro-structure on hard-brittle chip materials (HBCMs) surface can produce predominant functions and features. The micro-grinding with diamond wheel micro-tip is an efficient method to machine microstructure on HBCMs. However, different HBCMs and crystal orientation may have a significant influence on the micro-grinding performance. In this paper, the micro-grinding performance along different crystal orientation of HBCMs is investigated. First, a dressed 600^# diamond grinding wheel is used to micro-grind micro-structure on HBCMs. Then, the experiment of micro-grinding force test is completed. Finally, the quality of microgroove, the grinding ratio and the micro-grinding force are investigated and they are related to the crystal orientation of HBCMs. It is shown that the stronger resistance to the micro-crack propagation has the best quality of microgroove and the smallest grinding ratio. Moreover, the hardest single-crystal SiC has the best machinability and the micro-grinding force is 38.9%, 10.8% and 46.8% less than the one of sapphire, single-crystal Si and quartz glass, respectively. The direction to micro-grind easily is the crystal orientation 〈10\(\overline 1 \)0〉 for single-crystal SiC and sapphire. In addition, the micro-grinding force increases with the increase of the micro-grinding depth and feed rate and decreases with the increase of the grinding wheel speed.     

Lattice-based group signature with verifier-local revocation

Among several post quantum primitives proposed in the past few decades, lattice-based cryptography is considered as the most promising one, due to its underlying rich combinatorial structure, and the worst-case to average-case reductions. The first lattice-based group signature scheme with verifier-local revocation(VLR) is treated as the first quantum-resistant scheme supported member revocation, and was put forward by Langlois et al. This VLR group signature(VLR-GS) has group public key size of O(nm log N log q), and a signature size of O(tm log N log q log β). Nguyen et al. constructed a simple efficient group signature from lattice, with significant advantages in bit-size of both the group public key and the signature. Based on their work, we present a VLR-GS scheme with group public key size of O(nm log q) and signature size of O(tm log q). Our group signature has notable advantages: support of membership revocation, and short in both the public key size and the signature size.     

浅谈动车组转向架齿轮箱清洗检修设备验证与改造

对北京动车客车段动车检修基地前3列动车组检修设备验证实例进行了讨论,并结合设备改造情况进行了分析,提出了动车组检修设备验证、改造新思路。     

气压ABS系统流量特性的实验研究

开发了气压ABS电磁阀测试系统，建立了气室充、放气过程压力变化的微分方程，结合两者研究了气压ABS系统的流量特性，获得了某中型客车ABS系统在不同情况下的流量系数。讨论了ABS电磁阀的结构参数和动作频率对整个系统流量特性的影响，并得到了几种典型动作频率下的流量系数。建立的气室压力模型和所求得的流量系数为气压ABS控制逻辑的设计提供了依据。