行星齿轮式桥间差速器的差速特性分析

对行星齿轮式桥间差速器的传动原理、差速特性和扭矩分配特性进行的分析表明，采用该种差速器，在前后轮与地面间的附着条件相同且实际轴负荷分配也基本符合比例时，能够最有效的利用车轮与地面间的附着条件，使汽车的通过性能得到很大程度的提高；在后桥负荷大于前桥负荷的情况下，合理调整扭矩分配特性，可明显提高全轮驱动汽车的通过性能。     

汽车工业的柔性化战略探析

随着信息技术的发展,客户搜寻产品的成本越来越低,其需求逐渐表现出“个性化”特征。从用户拉动生产的理念出发,企业必须变产品导向为客户导向,通过为客户创造价值实现自身的生存和发展。文章对汽车工业现状进行了详细分析,得出集汽车柔性制造体系、柔性供应链体系、柔性服务营销策略和柔性组织管理为一体的柔性化战略是适合现代汽车工业发展的有效模式。     

论我国城市客车工况循环标准修改的重要性

介绍国内外城市客车工况循环的现状.通过分析指出,我国现有的城市客车四工况循环已不能满足城市客车与电动客车研发的需要,并针对此标准提出修改建议.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

Robust control for four-wheel-independent-steering electric vehicle with steer-by-wire system

A four-wheel-independent-steering (4WIS) electric vehicle (EV) with steer-by-wire (SBW) system is proposed in this paper. The fast terminal sliding mode controller (FTSMC) is designed for the SBW system to suppress external disturbances. Taking unstructured and structured uncertainties into consideration, a robust controller is designed for the 4WIS EV utilizing μ synthesis approach and the controller order reduction is implemented based on Hankel-Norm approximation. Since sideslip angle is the feedback signal of robust controller and it is hard to measure, the extended Kalman filter (EKF) is employed to estimate sideslip angle. To evaluate the vehicle performance with the designed control system, step and sinusoidal steering maneuvers are simulated and analyzed. Simulation results show that the designed control system have good tracking ability, strong robust stability and good robust performance to improve vehicle stability and handing performance.     

Bolster spring fault detection strategy for heavy haul wagons

An on-board health monitoring system is proposed for heavy haul wagons in this paper including a signal-based fault detection and isolation (FDI) method and an on-line fault diagnose strategy. Such a system, to be feasible on freight wagons, must be sufficiently cheap and robust, hence the design assumes the constraint of using only two accelerometers mounted on the front left and right rear part of each carbody in a heavy haul train. This paper focuses on the detection of bolster spring fault conditions. The problem is made more complex by the modes of failure which might be expected in bolster spring nests. Types of spring failure are firstly identified and discussed covering situations of broken (shortening springs) and softening (individual spring loss from a nest or cross-section loss through corrosion). The effects of these faults and their detectability were investigated using simulations on straight and curved track and using a fully detailed model of a typical 40?t axle-load heavy haul wagon. The simulation results were then examined and compared using cross-correlation analysis and an FDI system was proposed. The FDI system introduced five possible fault indicators. Initial results indicated that it was possible to detect changes in bolster stiffness of ±25%. An on-line fault diagnoses strategy is proposed for bolster spring faults which only requires data from wagon monitoring during travel around sharp curves to detect and the occurrence of confirm faults. The functionality envisaged needs only a ‘once per trip’ monitoring site, such as a sharper curve, and is aimed at condition monitoring rather than the provision of alarms or comprehensive monitoring of all events.     

ERP在柴油机柔性装配线上的应用

介绍了自主开发的“ERP”系统,及与之匹配的“取货制”物流配送,解决了在一条柔性装配线上装配650种以上机型混装问题,实现了企业计划、定单、技术准备、财务、质量和制造等的核心业务的网络控制,提高了企业的整体竞争力。     

浅谈异型拱桥桥型设计

通过一个桥型方案设计实例 ,简要介绍异型拱桥的特点     

基于海浪谱的3D海浪模拟

从海洋学的观测结果出发,利用海浪谱方法建立海浪的数学模型,使用LOD技术简化海面网格的计算量,并通过光照和纹理映射的渲染,实现深海区域的海浪模拟.实践证明使用该方法模拟海浪可以在实时性和真实感方面取得较好的效果.     

Singular perturbation composite control of a free-floating flexible dual-arm space robot

The Free-floating Flexible Dual-arm Space Robot is a highly nonlinear and coupled dynamics system. In this paper, the dynamic model is derived of a Free-floating Flexible Dual-arm Space Robot holding a rigid payload. Furthermore, according to the singular perturbation method, the system is separated into a slow subsystem representing rigid body motion of the robot and a fast subsystem representing the flexible link dynamics. For the slow subsystem, based on the second method of Lyapunov, using simple quantitative bounds on the model uncertainties, a robust tracking controller design is used during the trajectory tracking phase. The optimal control method is designed in the fast subsystem to guarantee the exponential stability. With the combination of the two above, the system can track the expected trajectory accurately, even though with uncertainty in model parameters, and its flexible vibration gets suppressed, too. Finally, some simulation tests have been conducted to verify the effectiveness of the proposed methods.