Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

不同加载幅值下考虑层间界面条件和侧向剪力作用的柔性铺面响应

该文进行了一个三维有限元参数量化的粘弹性路面响应研究,由于不同的轮胎配置:双轮和宽基轮胎在3种温度(5、25和40℃)和两种速度(8、72 km/h);还有影响路面响应的3种因素:移动车轮荷载幅值(连续,梯形),层间界面条件(简单的摩擦和粘弹性模型)和横向力共同对路面响应的影响进行了研究.研究发现连续加载幅值,不但可以模拟路面对运动轮荷载的响应,并且是一种比目前使用的梯形荷载幅值更准确的研究模型.粘弹性模型极大地提高了双轮胎对预测路面的响应,而简单的摩擦模型更接近宽基轮胎的实地测量.侧向剪力是积极改善预测轮底的表面磨损和底部热拌沥青(沥青)基层的较小程度上的应变.研究表明:使用连续加载幅值和非均匀压力分布模拟移动轮,侧向剪切力和适当的界面摩擦可显著改善有限元模型对车辆加载路面响应的预测能力.     

不同外加剂对OGFC混合料路用性能的影响

OGFC为开级配沥青混合料,主要由粗集料嵌挤组成,在世界各地越来越广泛地用于铺筑路面.OGFC混合料可以增大路表面渗透性,减少噪音,增强表面摩擦力,尤其是在潮湿条件下.该文主要研究不同外加剂对OGFC路用性能的影响,其混合料分别由再生聚乙烯改性沥青(RPEB)、橡胶粉改性沥青(CRMB)和70#基质沥青+纤维与矿料拌和而成.并分别采用析漏试验、肯塔堡飞散试验、渗水试验、劈裂试验、静态模量试验,车辙试验和抗滑试验评估OGFC混合料的路用性能.结果表明:纤维和聚合物可以有效地减小OGFC离析的可能性,混合料每面击实50次能相应地提高磨耗性和其他相关的性能.改性沥青混合料的抗拉强度比(TSR)低于纤维+基质沥青混合料的抗拉强度比.     

Design and implementation of a new clamping force estimator in Electro-Mechanical Brake systems

In this paper, an improved clamping force estimator is proposed for Electro-Mechanical Brake (EMB) systems by using the motor rotor position information and the hysteresis characteristics of mechanical parts in the EMB. A cascaded type of a force/position control system with a force sensor or an estimator was designed and implemented to control the clamping force and to keep the clearance gap in EMB systems. The EMB Hardware-In-the-Loop-Simulation (HILS) results show that the proposed force estimator yields better estimation performance than the existing estimator and that the clamping force control system based on the estimator can be also used for the fault tolerant control of the system.     

Experimental study on the impact characteristics of a sandwich composite with an aluminum foam core

The need for composites has been increasing in various industries because composites have good mechanical properties for their weight and superior stiffness and strength. The composites addressed in this study were multi-pore aluminum foam with a specific gravity of 1/10 composed of solid aluminum metal. This composite has excellent impact energy-absorption capability. In this study, impact tests on an aluminum foam core sandwich composite with a porous core were conducted to examine its mechanical properties. The specimen was a sandwich structure with an aluminum foam core, and different impact energies, such as 50J, 70J, and 100J, were applied to the specimen. Consequently, a maximum load of 5.5 kN occurred when the striker penetrated the upper face sheet in all experiments. The maximum load occurred at 4.2 ms for 50J, 3.5 ms for 70J, and 3.0 ms for 100J, indicating that the greater the impact energy was, the shorter the time was until the maximum load. After the maximum load occurred, that is, after the penetration of the upper face sheet, the striker penetrated 10 mm further, causing the core to be damaged in the 50J test, while the lower face sheet remained intact. In the 70J test, the striker penetrated the core and caused damage to the upper face sheet at 10 ms. Finally, in the 100J test, the striker penetrated both the upper face sheet and core and even the lower face sheet at 10 ms. Given the result above, the maximum load occurred when the striker penetrated the upper face sheet and the sandwich composite with aluminum foam core; the load then gradually decreased and then rapidly increased when the striker reached the lower face sheet, and the maximum load lasted slightly longer than the time required for the upper face sheet to be penetrated.     

Computational and experimental investigation of the unsteady flow structures around automotive outside rear-view mirrors

The unsteady flow field around two automotive outside rear-view mirrors is investigated. This study includes comprehensive experimental and computational approaches in order to characterize the complex flow structures in the wake of the mirrors. The experiments were carried out in a wind tunnel which included the measurements of the instantaneous and averaged velocity fields as well as mean and unsteady surface pressure distributions. The simulations were performed using Large Eddy Simulation (LES). The LES approach (particularly with the dynamic subgrid viscosity model) provided good agreements with the experiments for the velocity and the surface pressure distributions. The experimental and the computational results of this study will be used as a benchmark to validate the current and the future CFD development and the subsequent aero-acoustic computations.     

Exhaust emissions and its control methods in compression ignition engines: A review

Extensive usage of automobiles has certain disadvantages and one of them is its negative effect on environment. Carbon dioxide (CO₂), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and particulate matter (PM) come out as harmful products during incomplete combustion from internal combustion (IC) engines. As these substances affect human health, regulatory bodies impose increasingly stringent restrictions on the level of emissions coming out from IC engines. This trend suggests the urgent need for the investigation of all aspects relevant to emissions. It is required to modify existing engine technologies and to develop a better after-treatment system to achieve the upcoming emission norms. Diesel engines are generally preferred over gasoline engines due to their undisputed benefit of fuel economy and higher torque output. However, diesel engines produce higher emissions, particularly NO_x and PM. Aftertreatment systems are costly and occupy more space, hence, in-cylinder solutions are preferred in reducing emissions. Exhaust gas recirculation (EGR) technology has been utilized previously to reduce NO_x. Though it is quite successful for small engines, problem persists with large bore engines and with high rate of EGR. EGR helps in reducing NO_x, but increases particulate emissions and fuel consumption. Many in-cylinder solutions such as lower compression ratios, modified injection characteristics, improved air intake system etc. are required along with EGR to accomplish the future emission norms. Modern combustion techniques such as low temperature combustion (LTC), homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI) etc. would be helpful for reducing the exhaust emissions and improving the engine performance. However, controlling of autoignition timing and achieving wider operating range are the major challenges with these techniques. A comprehensive review of diesel engine performance and emission characteristics is given in this paper.     

山区峡谷非均匀风场下大跨度斜拉桥静风稳定性分析

为研究山区峡谷地形下非均匀风场对大跨度桥梁静风稳定性的影响,以一座跨越典型山区峡谷地形的大跨度斜拉桥为工程背景,首先,采用计算流体动力学（CFD）软件Fluent对桥址区地形的风场特性进行分析,计算出沿主梁方向的非均匀风速和非均匀风攻角分布;然后,采用ANSYS APDL技术实现能考虑非均匀风速和非均匀风攻角下大桥静风稳定性的非线性分析方法。在此基础上,综合考察非均匀风攻角分布、非均匀风速分布、非均匀风速非均匀风攻角分布等风场条件对大桥静风稳定性的影响,分析各工况下主梁的静风变形与跨中处拉索刚度变化。研究结果表明：与均匀风场条件下的静风响应不同,非均匀风攻角或非均匀风速下主梁静风响应最大值点位于风荷载峰值点与跨中之间,在针对非均匀风场下大桥的静风稳定性分析时,应更注重静风响应最大值点而不是跨中处;非均匀风攻角下大桥的静风失稳临界风速要远低于均匀风攻角的静风失稳临界风速,且其静风稳定性能主要受最大风攻角而不是主跨部分非均匀风攻角的平均值来控制;非均匀风速下大桥的静风失稳临界风速主要由主跨部分的风速平均值和最大值共同影响;主梁的竖向位移和扭转角形状主要由风攻角因素来控制,而横向位移的变化规律相对较独立,其形状基本上以跨中线对称,且其值主要由风速因素来决定。     

Operating speed pattern optimization of railway vehicles with differential evolution algorithm

The railway transportation system has much advantage in eco-friendliness, punctuality and safety compared to any other transportation system. Most of the railway system administrators have to control and operate under limited resources such as trains and facilities. It is necessary to control traveling time and energy consumption for efficient operation in the railway systems, because the board rate of passenger is inconstant with time variance. It is common that the shorter traveling time causes the greater energy consumption. In this study, a new optimization method considering operation time or energy consumption is proposed by using differential evolution algorithm and some cases are reviewed. The total energy change due to operation time variation are investigated by using the proposed optimization method for tangent and gradient track conditions. Both cases, the total energy decreases exponentially. However, because of gradient the total energy are saturated after a certain time for gradient track.