Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Optimized design for a MacPherson strut suspension with side load springs

Undesired lateral force inevitably exists in a MacPherson suspension system, which is liable to damper rod’s side wear and promotes the damper’s inner friction decreasing the ride performance from the suspension system. Substituting a new side load spring with curved centerline for the conventional coil spring has been proven able to solve these problems and Multi-body Dynamics combining with Finite Elements Analysis may be an efficient method in optimizing its design. Therefore, taking a passenger car as example, a detailed multi-body dynamics model for the suspension system is built to simulate forces exerted on the damper and the minimization of its lateral component is selected as the design target for the spring. When the structure optimization of the side load spring is performed using FEA software ANSYS, its vertical and lateral elastic characteristics, supported by test data, are analyzed. After importing FEA results back to the suspension system, the dynamics simulation can be performed to validate the optimization result.     

Analysis process of a steering system using a concept model for idle vibration

This paper describes the development of an optimal design process for a steering column system and supporting system. A design guide is proposed at the initial concept stage of the development process to obtain sufficient stiffness of the steering system while reducing the idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, where vibration modes among the systems are separated by applying a vibration mode map at the initial stage of the design process. This study also provides design guidelines for an optimal dynamic damper system using a CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to the vehicle model to analyze the relation between the frequency and the sensitivity of the steering column system. This analysis methodology makes it possible to achieve target performance in the early design stage and reduction of damper tuning activity after the proto car test stage. Through the proposed steering column system development process, a lightweight vehicle with high stiffness is possible prior to the proto build stage. Furthermore, the improved process is expected to contribute to reducing the overall development period and the number of proto car tests necessary to achieve the desired steering system performance.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

The impact of job assignment rules for straddle carriers on the throughput of container terminals

Straddle carriers represent a critical resource in the handling of containers within a container terminal. It is essential that they are deployed in an as efficient manner as possible. The research presented in this paper is motivated by the need to critically evaluate job assignment rules for straddle carriers that operate in a multiple straddle environment. This is achieved by developing a discrete event simulation model using industrial simulation software to model a container terminal located in Melbourne, Australia. The model accounts for variables such as the number of straddle carriers needed, the speed of straddle carriers, the arrival rate of trucks, and the job assignment rule. A principal finding of the study is that increasing the number of straddles in the present set‐up from 6 to 7 has a negligible effect on daily throughput. However, an increase in the number of straddles to 7 is expected to have a profound effect on reducing the average waiting time of trucks within the terminal from over 16 minutes to under 9 minutes, a decrease of 46.5%. However, a further increase in the number of straddles results in no further increase in daily throughput. It was observed that the throughput of the terminal is very sensitive to the speeds at which straddles travel. The management of the terminal has proposed a new heuristic job assignment rule for straddles, because the present rule does not assign the jobs to straddles closest to the truck requesting to load or unload a container. As a result a new heuristic job assignment rule was tested. The simulation results revealed that both the old and new rules performed equally well using performance indicators such as average container flow time, daily throughput, average waiting time of jobs, number of jobs in the queue, and straddle utilisation. Therefore, the new rule will not improve these performance measures if implemented     

Access control policies without inside queues: Their properties and public policy implications

An access control policy that eliminates all queues beyond the entry points to a network has obvious benefits, which include smooth travel and predictable travel times inside the network. Yet it has never been proven, to the best of our knowledge, whether excluding inside queues yields sub-optimal network performance or, in other words, allowing inside queues can actually further reduce the system travel cost. Moreover, it is not clear whether an optimal control policy derived from efficiency considerations can also be a fair policy to all road users. This paper provide answers to these questions in the context of a monocentric network. By analyzing the structure of the access control problem considering all feasible policies (with/without inside queues), we show that the minimal system cost realizable by access control can be obtained without directly solving a non-convex optimization program, and can indeed always be achieved by a control policy excluding all of the inside queues. These optimal policies are defined by a polyhedral set and a Finite Generation Algorithm can be applied to derive the analytical form of this set. The optimal policies are not unique in general, thus making it possible to achieve both minimal system cost and fairness simultaneously.     

Red-light cameras at intersections: Estimating preferences using a stated choice model

Red-light cameras placed at intersections have the potential to increase safety, but they are often viewed as an invasion of privacy. Preferences for these cameras were explored using a stated choice model that presents key attributes of camera placements. Stated choice models involve careful experimental design, akin to experimental control in laboratory settings. A variety of design approaches were used, settling on a composition of the choice sets people face in the survey. To illustrate the approach, an internet survey was used with a convenience sample containing a high percentage of college students. The results show that while not the case independently, as the number of cameras and fines for violators are simultaneously increased, the preferences for one particular red light cameras program are likely to improve.     

Contracting in highway maintenance and rehabilitation: Are spatial effects important?

Highway agencies around the world strive to improve practices for infrastructure maintenance and rehabilitation, using project delivery policies that range from total ‘in-house’ responsibility to complete privatization, with a number of flexible contracting policies such as performance-based contracting, variants of design-build-maintain, and lane rentals among others between these two extremes. In this paper, we present a methodology that duly accounts for underlying spatial effects and estimates the expected cost savings of innovative contracting policies for highway maintenance and rehabilitation relative to in-house execution of these activities. Spatial econometric modeling is used to analyze highway contract data from 49 countries. We also investigate the marginal effects of key explanatory variables on contract cost savings using spatial multipliers. Our findings show that there are significant relationships between cost savings and contract characteristics, and that there is an apparent direct relationship between the average cost savings of contracts in a country and contract average cost savings and contract sizes in neighboring countries.     

Prospects for plug-in hybrid electric vehicles in the United States and Japan: A general equilibrium analysis

The plug-in hybrid electric vehicle (PHEV) may offer a potential near term, low-carbon alternative to today’s gasoline- and diesel-powered vehicles. A representative vehicle technology that runs on electricity in addition to conventional fuels was introduced into the MIT Emissions Prediction and Policy Analysis (EPPA) model as a perfect substitute for internal combustion engine (ICE-only) vehicles in two likely early-adopting markets, the United States and Japan. We investigate the effect of relative vehicle cost and all-electric range on the timing of PHEV market entry in the presence and absence of an advanced cellulosic biofuels technology and a strong (450 ppm) economy-wide carbon constraint. Vehicle cost could be a significant barrier to PHEV entry unless fairly aggressive goals for reducing battery costs are met. If a low-cost PHEV is available we find that its adoption has the potential to reduce CO₂ emissions, refined oil demand, and under a carbon policy the required CO₂ price in both the United States and Japan. The emissions reduction potential of PHEV adoption depends on the carbon intensity of electric power generation. Thus, the technology is much more effective in reducing CO₂ emissions if adoption occurs under an economy-wide cap and trade system that also encourages low-carbon electricity generation.