Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.     

Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

Effect of fuel stratification on initial flame development: Part 3-high swirl condition

This paper discusses the final investigation into the effect of fuel stratification on flame propagation. In previous works, the characteristics under the no port-generated swirl condition and the low-swirl condition were considered. For this purpose, the initial flame development and propagation were visualized under different axially stratified states in a modified optical single-cylinder SI engine. The images were captured by an intensified CCD camera through the quartz window mounted in the piston. Stratification was controlled by the combination of the port swirl ratio and injection timing. These were averaged and processed to characterize the flame propagation. The flame stability was estimated by the weighted average of flame area and luminosity. The stability was also evaluated through the standard deviation of flame area and propagation distance and through the mean absolute deviation of the propagation direction. The results show that the LML is expanded remarkably under the high-swirl cases up to the highest relative AFRs of 1.71 and 1.75 between 140 and 160CA. In addition, similar to the low-swirl condition, the flame-flow interaction determines the direction of flame propagation, and the governing roles of the two factors vary according to the swirl level; the flow is more important at the higher swirl conditions, and the flame is more important at the lower swirl condition. Finally, fast and stable flame propagation can be achieved under the preferably stratified condition, which is induced by the suitable combination of the high swirl and injection timing.     

两种直接波浪能转换系统性能的比较:阿基米德波浪摆和波能浮筒(英文)

Many wave energy conversion devices have not been well received. The main reasons are that they are too complicated and not economical. However, in the last two decades direct conversion systems have drawn the attention of researchers to their widely distributed energy source due to their simple structure and low cost. The most well-known direct conversion systems presently in use include the Archimedes Wave Swing (AWS) and Power Buoy (PB). In this paper, these two systems were simulated in the same conditions and their behaviors were studied in different wave conditions. In order to verify the simulations, results of the generator of the finite element computations were followed. An attempt was made to determine the merits and drawbacks of each method under different wave conditions by comparing the performance of the two systems. The wave conditions suitable for each system were specified.     

双通线加热的热力学及实验分析(英文)

The present investigation deals with process analysis of oxy-acetylene flame assisted double pass line heating for varying plate thickness. oxy-acetylene flame as the heat source for multi pass line heating to achieve 3-D bending of plates with varying thicknesses was studied. The oxy-acetylene flame was modeled as the moving heat source in the FEM analysis. The transient thermal histories were predicted taking into account the temperature dependent thermo-mechanical properties. A comparative study between single pass and double pass line heating residual deformation was also carried out. The temperature distribution and residual deformations predicted by the numerical model developed in the present work compared fairly well with those of the experimental ones.     

Experimental Investigation of TARMAX Model for Modeling of Hydrodynamic Forces on Cylinder-like Structures

A new approach that models lift and drag hydrodynamic force signals operating over cylindrical structures was developed and validated. This approach is based on stochastic auto regressive moving average with exogenous (ARMAX) input and its time-varying form, TARMAX. Model structure selection and parameter estimation were discussed while considering the validation stage. In this paper, the cylindrical structure was considered as a dynamic system with an incoming water wave and resulting forces as the input a...     

A generic class of first order node models for dynamic macroscopic simulation of traffic flows

Node models for macroscopic simulation have attracted relatively little attention in the literature. Nevertheless, in dynamic network loading (DNL) models for congested road networks, node models are as important as the extensively studied link models. This paper provides an overview of macroscopic node models found in the literature, explaining both their contributions and shortcomings. A formulation defining a generic class of first order macroscopic node models is presented, satisfying a list of requirements necessary to produce node models with realistic, consistent results. Defining a specific node model instance of this class requires the specification of a supply constraint interaction rule and (optionally) node supply constraints. Following this theoretical discussion, specific macroscopic node model instances for unsignalized and signalized intersections are proposed. These models apply an oriented capacity proportional distribution of the available supply over the incoming links of a node. A computationally efficient algorithm to solve the node models exactly is included.     

Simulating the impacts of household travel on greenhouse gas emissions,urban air quality,and population exposure

This paper establishes a link between an activity-based model for the Greater Toronto Area (GTA), dynamic traffic assignment, emission modelling, and air quality simulation. This provides agent-based output that allows vehicle emissions to be tracked back to individuals and households who are producing them. In addition, roadway emissions are dispersed and the resulting ambient air concentrations are linked with individual time-activity patterns in order to assess population exposure to air pollution. This framework is applied to evaluate the effects of a range of policy interventions and 2031 scenarios on the generation of vehicle emissions and greenhouse gases in the GTA. Results show that the predicted increase of approximately 2.6 million people and 1.3 million jobs in the region by 2031 compared to 2001 levels poses a major challenge in achieving meaningful reductions in GHGs and air pollution.     

Discretionary activity location choice: in-home or out-of-home?

This paper examines the location choice associated with discretionary activities (in-home vs. out-of-home). These substitution patterns are important in terms of travel demand as in-home activities do not necessitate travel while out-of-home activities incur travel. Mixed logit models are estimated using an activity dataset (2003 CHASE data) to analyze the factors associated with this choice at the individual activity-level. Results suggest that the attributes of an activity significantly contribute to understanding the likelihood of engaging in out-of-home activities. Activity type interaction terms reveal the varying influence that socio-demographics, activity attributes and travel have over four different activity types modeled. The results reveal that the location choice (in-home vs. out-of-home) is sensitive to travel characteristics. As the travel time and cost increases, an individual is less likely to engage in an activity out-of-home. Compared to passive and social activities, the location of active activities is more sensitive to changes in travel attributes.     

Experimental design influences on stated choice outputs: An empirical study in air travel choice

Discrete choice experiments are conducted in the transport field to obtain data for investigating travel behaviour and derived measures such as the value of travel time savings. The multinomial logit (MNL) and other more advanced discrete choice models (e.g., the mixed MNL model) have often been estimated on data from stated choice experiments and applied for planning and policy purposes. Determining efficient underlying experimental designs for these studies has become an increasingly important stream of research, in which the objective is to generate stated choice tasks that maximize the collected information, yielding more reliable parameter estimates. These theoretical advances have not been rigorously tested in practice, such that claims on whether the theoretical efficiency gains translate into practice cannot be made. Using an extensive empirical study of air travel choice behaviour, this paper presents for the first time results of different stated choice experimental design approaches, in which respective estimation results are compared. We show that D-efficient designs keep their promise in lowering standard errors in estimating, thereby requiring smaller sample sizes, ceteris paribus, compared to a more traditional orthogonal design. The parameter estimates found using an orthogonal design or an efficient design turn out to be statistically different in several cases, mainly attributed to more or less dominant alternatives existing in the orthogonal design. Furthermore, we found that small designs with a limited number of choice tasks performs just as good (or even better) than a large design. Finally, we show that theoretically predicted sample sizes using the so-called S-estimates provide a good lower bound. This paper will enable practitioners in better understanding the potential benefits of efficient designs, and enables policy makers to make decisions based on more reliable parameter estimates.