Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

Transient characteristics of emissions during engine start/stop operation employing a conventional gasoline engine for HEV application

In this paper, we investigate the transient characteristics of combustion and emissions during engine start/stop operations in hybrid electric vehicle (HEV) applications. Hydrocarbon (HC) emissions during the initial 2^nd∼9^th cycles are found to be significantly greater when the engine is quickly started under the original engine calibration mode. Lower intake manifold absolute pressure (MAP) was also found to cause larger residual gas dilution and poor combustion, resulting in a higher HC concentration when the cranking speed was increased. The post-catalyst HC concentration was found in the way of initially decrease and then to increase again as the cranking speed was increased. A lowest concentration value was achieved at a cranking speed of 1000 r/min. Engine shut-down by fuel cut-off was shown to produce lower emissions than shut-down by ignition cut-off as one can avoid misfire of the last fuel injection cycle. The fuel deposited during the stop process seems to impact engine restart enrichment mostly during the initial 0.7 s for this engine, whose performance is dominated by the MAP transition characteristic and the time coefficient for fuel vaporization in this time period     

不同稳定剂对SBS改性沥青稳定效果的对比研究

通过试验测试不同老化时间样品的针入度、软化点和延度比较其相容性和路用流变学性能指标的变化,分析体系宏观稳定性和稳定剂性能特征,并通过形态结构照片分析稳定剂改善的效果。结果表明,加入稳定剂后改性沥青的高温储存稳定性明显改善,同时加入FD-06无硫稳定剂的改性沥青在热储存过程中性能更加稳定,不易离析。沥青中的部分组份具有化学活性,利用其活性点,引入带有活性基团的反应物,并通过被引入分子的化学结构的调节改善SBS与沥青的相容性,从而制备储存稳定性良好的SBS改性沥青。化学改性技术的应用提高了路用改性沥青的性能/价格比。     

A fundamental investigation of tilt control systems for narrow commuter vehicles

One way of addressing traffic congestion is by efficiently utilizing the existing highway infrastructure. Narrow tilting vehicles that need a reduced width lane can be part of the solution if they can be designed to be safe, stable, and easy to operate. In this paper, a control system that stabilizes the tilt mode of such a vehicle without affecting the handling of the vehicle is proposed. This control system is a combination of two different types of control schemes known as steering tilt control (STC) and direct tilt control (DTC) systems. First, different existing variations of both STC and DTC systems are considered and their shortcomings analysed. Modified control schemes are then suggested to overcome the deficiencies. Then a new method of integrating these two control schemes that guarantees smooth switchover between the controllers as a function of vehicle velocity is proposed. The performance of the proposed STC, DTC, and integrated systems is evaluated by carrying out simulations for different operating conditions and some experimental work. The design of a second-generation narrow tilting vehicle on which the developed control system has been implemented is presented.     

The chatter of racing motorcycles

The chatter of motorcycles appears during braking and consists of a vibration of the rear and front unsprung masses at a frequency in the range of 17-22 Hz depending on the motorcycle. This vibration could be very strong and acceleration of the unsprung masses can reach 5-10 g. The chatter is an auto-excited vibration and this fact explains why it appears suddenly when the mechanism of auto-excitation is generated. This paper presents the chatter phenomenon both from an experimental and a numerical point of view. First, the chatter is defined on the basis of some experimental data from racing motorcycles and from the comments of some racing teams technicians. Then, chatter is analysed in different motion conditions and for different braking styles by means of linear and non-linear simulations of the motorcycle dynamics. A physical interpretation of the phenomenon is also proposed.     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Experimental research of the EQ6110HEV hybrid electric bus using an on-line debugging system

This paper describes the on-line debugging software developed by our research team. The software has five functions and can be helpful in achieving rapid development for hybrid electric buses. In addition, the software can monitor system states continuously and also modify parametric maps or update control programs using its on-line programming function. Based on the on-line debugging system, the hybrid propulsion control system is designed, and all the working modes of the hybrid electric bus are tested. Finally, experiments are carried out that verify that the debugging system is feasible and reliable. The test results show that the hybrid electric bus can reduce fuel consumption by about 19.1 percent, in comparison with conventional buses.     

杭州湾跨海大桥混凝土结构耐久性原位监测预警系统

为了确保杭州湾跨海大桥混凝土结构达到百年设计使用寿命,评价混凝土结构耐久性状况的动态发展,通过对预埋式钢筋腐蚀无损监测传感系统的国际合作研究,确定了基于电化学原理和辅助光纤技术的耐久性监测技术思路,制定了该工程耐久性动态预报监测平台的构架技术方案,捕获了结构各部位腐蚀预警的个性化判据,优化了全桥测点的布置,集成、改良并安装了控制关键部位的全套系统(共计48套监测单元)。工程实测结果表明:测试数据稳定,并且与实验室研究数据吻合。     

Model-based design of a variable nozzle turbocharger controller

Variable Nozzle Turbocharger (VNT) was invented to solve the problem of matching an ordinary turbocharger with an engine. VNT can harness exhaust energy more efficiently, enhance intake airflow response and reduce engine emissions, especially during transient operating conditions. The difficulty of VNT control lies in how to regulate the position of the nozzle at different engine working conditions. The control strategy designed in this study is a combination of a closed-loop feedback controller and an open-loop feed-forward controller. The gain-scheduled proportional-integral-derivative (PID) controller was implemented as the feedback controller to overcome the nonlinear characteristic. As it is difficult to tune the parameters of the gain-scheduled PID controller on an engine test bench, system identification was used to identify the plant model properties at different working points for a WP10 diesel engine on the test bench. The PID controller parameters were calculated based on the identified first-order-plus-dead-time (FOPDT) plant model. The joint simulation of the controller and the plant model was performed in Matlab/Simulink. The time-domain and frequency-domain performances of the entire system were evaluated. The designed VNT control system was verified with engine tests. The results indicated that the real boosting pressure traced the target boosting pressure well at different working conditions.