Comparative analysis of vehicle brake data in the ministry of transport test on the roller brake tester and on flat ground

This study performs a comparison between what occurs when braking on a Ministry of Transport (MOT) brake tester and on flat ground. The tire pressure is changed, but the other parameters remain constant. The results from this research and from the in-depth comparative study conducted by the mechanical engineering staff in the mechanical laboratory at the Miguel Hernández University in Elche have led to the following main conclusions: By varying the tire pressure, false results can be obtained with the MOT brake tester, which means that, if the tires are inflated at a low pressure but the brakes are in good condition, the vehicle will not pass the MOT. Conversely, if the brakes are in poor condition but the tire pressure is higher than what is recommended by the manufacturer, a false pass is produced. This article shows that the MOT brake testing equipment is often wrong and inexact, and the data and graphs presented prove that the tire pressure is a determining factor when assessing the condition of brakes.     

Aerodynamic design optimization of rear body shapes of a sedan for drag reduction

This study proposes an aerodynamically optimized outer shape of a sedan by using an Artificial Neural Network (ANN), which focused on modifying the rear body shapes of the sedan. To determine the optimization variables, the unsteady flow field around the sedan driving at very fast speeds was analyzed by CFD simulation, and fluctuations of the drag coefficient (C _D ) and pressure around the car were calculated. After consideration of the baseline result of CFD, 6 local parts from the end of the sedan were chosen as the design variables for optimization. Moreover, an ANN approximation model was established with 64 experimental points generated by the D-optimal methodology. As a result, an aerodynamically optimized shape for the rear end of the sedan in which the aerodynamic performance is improved by about 5.64% when compared to the baseline vehicle is proposed. Finally, it is expected that within the accepted range of shape modifications for a rear body, the aerodynamic performance of a sedan can be enhanced so that the fuel efficiency of the sedan can be improved. The YF SONATA, a sedan manufactured by Hyundai Motors Corporate, played a major role in this research as the baseline vehicle.     

A self-powering system based on tire deformation during driving

Tire intelligence is vital in the improvement of the safety of vehicles because the tire supports the car body and is the contact point between the vehicle and the road. To create an intelligent tire, sensors must be installed to measure the behavior of the tire. However, it is difficult to apply a wired sensor system on the wheel of the tire. Hence, it is necessary to implement a self-powering, wireless system (a type of energy harvesting system) that can be mounted inside the tire. The purpose of this study is to convert the strain energy caused by deformation of the tire while driving into useful electrical energy to supply the sensor system. A flexible piezofiber is utilized for the energy conversion. The variation in strain, due to changes in speed, load, and the internal pressure of the tire, was measured along two axial directions to evaluate the amount of available strain energy. The amount of strain changed from 0.15% to 0.8%. To predict the amount of available energy from a tire, we perform an analysis of the relationship between the strain and the voltage. In addition, experiments for impedance matching between piezofiber and related circuits were conducted to optimize the external loads for transferring energy efficiently. Based on the procedure mentioned above, at least 0.58 mJ of electrical energy can be generated by using the laterally oriented strain (1500 to 2500 micro strain). The result of this study is expected to enhance the potential realization of self-generating wireless sensor systems for so-called ??intelligent?? tires.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

Fuel consumption of fuel cell hybrid vehicles considering battery SOC differences

Fuel cell hybrid vehicles (FCHVs) have become one of the most promising candidates for future transportation due to current energy supply problem and environmental problem. Fuel economy is an important factor in FCHVs. In order to properly evaluate the fuel economy of an FCHV, the initial battery state of charge (SOC) and the final battery SOC have to be identical so that the effect of the battery energy usage on the fuel economy is neglected. In the simulation or in the real driving, however, the final battery SOC is usually different from the initial battery SOC, and the final battery SOC often depends on the power management strategy. To consider the difference between the two battery SOC values, the concept of equivalent fuel consumption is presented by two methods. One is based on the relationship between delta SOC and delta fuel consumption, and the other is based on the optimal control theory. Two rule-based power management strategies for an FCHV are presented, and for each strategy, the fuel economy is evaluated based on the two methods. The characteristics of the two methods are discussed and compared, and the superior one is selected based on the comparison.     

青浦第二污水厂运行现状及三期工程设计与运行

青浦污水厂一、二期工程设计规模分别为1.5万m3/d和4.5万m3/d,均采用Carrousel氧化沟工艺,最终出水执行《城市污水处理厂污染物排放标准》(GB18918-2002)一级B标准。该文介绍了其工程设计与运行情况。在工程设计中,通过对一、二期工程分析,借鉴了相关工程的设计经验,优化了三期工程工艺设计及运行参数,总结了设计及运行方面的经验,为相关工程提供借鉴与参考。     

增程式电动车驱动系统的参数匹配与仿真研究

文中介绍了增程式电动汽车驱动系统主要部件参数的匹配方法,并运用PSAT仿真软件对所设计系统进行动力性和经济性的模拟计算,仿真结果表明所设计匹配的驱动系统基本满足车辆的性能要求。     

Policy challenges of increasing automation in driving

The convergence of information and communication technologies (ICT) with automotive technologies has already resulted in automation features in road vehicles and this trend is expected to continue in the future owing to consumer demand, dropping costs of components, and improved reliability. While the automation features that have taken place so far are mainly in the form of information and driver warning technologies (classified as level I pre-2010), future developments in the medium term (level II 2010–2025) are expected to exhibit connected cognitive vehicle features and encompass increasing degree of automation in the form of advanced driver assistance systems. Although autonomous vehicles have been developed for research purposes and are being tested in controlled driving missions, the autonomous driving case is only a long term (level III 2025 +) scenario. This paper contributes knowledge on technological forecasts regarding automation, policy challenges for each level of technology development and application context, and the essential instrument of cost-effectiveness for policy analysis which enables policy decisions on the automation systems to be assessed in a consistent and balanced manner. The cost of a system per vehicle is viewed against its effectiveness in meeting policy objectives of improving safety, efficiency, mobility, convenience and reducing environmental effects. Example applications are provided that illustrate the contribution of the methodology in providing information for supporting policy decisions. Given the uncertainties in system costs as well as effectiveness, the tool for assessing policies for future generation features probabilistic and utility-theoretic analysis capability. The policy issues defined and the assessment framework enable the resolution of policy challenges while allowing worthy innovative automation in driving to enhance future road transportation.     

基于发动机联合控制的AMT换挡控制策略

分析了AMT换挡类型,提出了基于CAN总线的发动机联合控制策略,即TCU通过CAN及ECU扭矩控制功能对发动机扭矩进行精确控制,同时基于发动机瞬态扭矩对离合器实现精确分离和接合控制.针对不同换挡工况给出了离合器分离/接合与发动机降扭/扭矩恢复协调控制策略,同时提出了选换挡过程动态调整转速控制策略.试验结果表明,所提策略可以增强AMT换挡过程的平顺性和动力性,减小离合器滑摩,且具有很好的鲁棒性,有助于提高AMT换挡品质.     

车联网标识解析体系研究

车联网标识解析体系是建立在工业互联网相关技术之上,针对车路协同、自动驾驶、车辆运行等交通环节的设备赋予全局唯一的标识.本文介绍了我国工业互联网标识解析体系的建设与技术发展情况,提出了车联网标识解析体系的实施框架与技术架构.通过建立车联网标识解析体系,可以实现车联网信息通信的身份验证、高效传输与安全保障,助力车联网的发展...