Performance evaluation of slim low-risk-deployment dual-type passenger airbag system with dispersed inflation pressure

Motor vehicle passenger airbags have been proven to be effective for reducing the possibility of passenger injury during a crash. However, the inflation of the airbag sometimes causes serious injury when a passenger is positioned close to the airbag. The United States Federal Motor Vehicle Safety Standard (FMVSS) 208 requires the use of a low-riskdeployment (LRD) passenger airbag system. This paper proposes a newly developed airbag system comprising two slim airbags mounted on the instrument panel. A series of tests were conducted using the FMVSS 208 test procedures to demonstrate the effectiveness of the proposed system. It was found that the system not only satisfied the injury criteria of FMVSS 208, but was also effective for protecting passengers of all sizes.     

Influence of turpentine addition in Jatropha biodiesel on CI engine performance,combustion and exhaust emissions

The prospect of using turpentine oil as an additive for Jatropha biodiesel and using it as an alternative fuel for diesel in CI engines has been experimented in this work. Tests were carried out in a single cylinder, air cooled, constant speed, direct injection diesel engine. The results display that the performance of Jatropha-Mineral Turpentine (JMT) and Jatropha- Wood Turpentine (JWT) blends were found close to diesel, emission features were enhanced and combustion parameters were noticed to be comparable with diesel. Brake thermal efficiency of JMT20 blend found closer to diesel at 75 % load. BSFC increases for JMT and JWT blends at part load and maintains at full load. CO, HC and Smoke emissions were reduced with JMT and JWT blends at 75 % load. NOx emissions were on the raise. Furthermore, JMT and JWT blends offered comparable performance and combustion parameters, reduced emissions and both can substitute standard diesel in CI engines.     

Lateral stability control of dynamic steering for dual motor drive high speed tracked vehicle

In this paper, the torque and power required by dual motors for electric tracked vehicle during dynamic steering maneuvers with different steering radiuses are analyzed. A steering coupling drive system composed of a new type of center steering motor, two Electromagnetic (EM) clutches, two planetary gear couplers, and two propulsion motors is proposed for the dual motors drive high speed electric tracked vehicle (2MHETV), which aims to improve its lateral stability. An average torque direct distribution control strategy based on steering coupling and an optimization-distribution-based close-loop control strategy are designed separately to control the driving torque or regenerative braking torque of two propulsion motors for vehicle stability enhancement. Then models of the 2MHETV and the proposed control strategy are established in Recudyn and Matlab/Simulink respectively to evaluate the lateral stability of dynamic steering for the 2MHETV with different steering radiuses on hard pavement.The simulation results show that the lateral stability of the 2MHETV can be significantly improved by the proposed optimization-distribution-based close-loop control strategy based on steering coupling system.     

Analysis of wheel speed vibrations for road friction classification

ABSTRACT

With higher level of vehicle automation, it becomes increasingly important to know the maximum possible tyre forces during normal driving. An interesting method in this respect is estimating the tyre–road friction from the resonance peak in the wheel speed signal, excited by road roughness. A simulation environment using the MF-Swift tyre model is proposed, which gives insight in the correctness and functioning of this method. From implementing the estimation algorithm and considering the tyre torsional vibration system, it is concluded that frequencies and damping ratios can be estimated with reasonable accuracy and that the trends observed with changing road friction are consistent. Furthermore, the proposed simulation environment gives opportunity to investigate other issues like robustness of the estimation method to road roughness. Additionally, the tyre modelling aspect of the estimation method is analysed and improvements are proposed.     

Study on rail corrugation of a metro tangential track with Cologne-egg type fasteners

In Chinese metro lines, rail corrugation on both tangential and tight curved tracks with Cologne-egg type fasteners is very severe. Based on the viewpoint of friction-induced vibration causing rail corrugation, the rail corrugation on a tangential track with Cologne-egg type fasteners is studied in this paper. A vibration model of an elastic multiple-wheelset-track system with Cologne-egg type fasteners is established. Both the complex eigenvalue analysis and the transient dynamic analysis are performed to study the stability and the dynamic performance of the wheelset-track system. The simulation results show that a low rail support stiffness value is responsible for rail corrugation on the tangential track. When the Cologne-egg fasteners characterised by a lower stiffness value are replaced with the DTVI2 fasteners characterised by a higher stiffness value, rail corrugation disappears. However, rail corrugation on tight curved tracks cannot be suppressed using the same replacement. The above conclusions are consistent with the corrugation occurrences in actual metro tracks.     

Measurement of hydrocarbon and carbon monoxide emissions during the starting of automotive DI Diesel engines

Most of hydrocarbon (HC) and carbon monoxide (CO) emissions from automotive DI Diesel engines are produced during the engine warm-up period and are primarily caused by difficulties in obtaining stable and efficient combustion under these conditions. Furthermore, the contribution of engine starting to these emissions is not negligible; since this operating condition is highly unfavorable for the combustion progress. Additionally, the catalytic converter is ineffective due to the low engine temperature. In conjunction with adequate engine settings (fuel injection and fresh air control), either the glow plugs or the intake air heater are activated during a portion of the engine warm-up period, so that a nominal engine temperatures is reached faster, and the impact of these difficulties is minimized. Measurement of gaseous pollutants during engine warm-up is currently possible with detectors used in standard exhaust gas analyzers (EGA), which have response times well-suited for sampling at such transient conditions. However, these devices are not suitable for the measurement of exhaust emissions produced during extremely short time intervals, such as engine starting. Herein, we present a methodology for the measurement of the cumulative pollutant emissions during the starting phase of passenger car DI Diesel engines, with the goal of overcoming this limitation by taking advantage of standard detectors. In the proposed method, a warm canister is filled with an exhaust gas sample at constant volumetric flow, during a time period that depends on the engine starting time; the gas concentration in the canister is later evaluated with a standard EGA. When compared with direct pollutant measurements performed with a state-of-art EGA, the proposed procedure was found to be more sensitive to combustion changes and provided more reliable data.     

闪急沸腾喷雾研究的现状与展望

阐述了闪急沸腾喷雾的基本原理,通过比较分析闪急沸腾喷雾与传统喷雾的差异,指出闪急沸腾喷雾是一种极具潜力的燃油喷射方式;论述了近年来国内外对过热燃油和溶气燃油闪急沸腾喷雾研究的进展与现状,介绍了过热液体闪急沸腾喷雾的数学模型及其发展,并从理论上分析了影响闪急沸腾喷雾的因素;展望了闪急沸腾喷雾的应用前景以及进一步研究的发展方向。     

Possibility of jamming and wedging in the three-piece trucks of a moving freight car

Three-piece trucks have some drawbacks, particularly unstable operation of the friction wedge damping system. One of the principal features of systems of this kind is the possibility of jamming and wedging. This work is devoted to mathematical and numerical modeling of the plane motion of a freight car with allowance for the mobility of the wedges and then for the compliance of the contacting bodies and to the study of the conditions for the onset of jamming and wedging when the car is in motion.     

Load-leveling suspension system with a magnetorheological damper

In this paper, a load-leveling suspension system with a magnetorheological (MR) damper is investigated. In this suspension system, the MR damper is connected to a spring to form a load-leveling suspension system. The system effective stiffness and damping can be adjusted by controlling the MR damper. The characteristics of a load-leveling suspension system are studied first. When the linear damper is replaced with an MR damper, the averaging method is adopted to obtain the steady-state response of the nonlinear system. A comparison demonstrates that the results of the averaging method are in good agreement with those obtained by numerical simulations. The analytical results are then verified experimentally. The load-leveling suspension system studied here is able to adjust both suspension stiffness and damping and, hence, it may provide more effective vibration control in a wider frequency range, when the damper is controlled.