A Multi-Spoke, Three Plane Tyre Model for Simulation of Transient Behaviour

Based on the multi-spoke, single-plane, steady-state tyre model, a transient multi-spoke, three-plane tyre model is presented. This model involves updating the states of all the spokes under consideration to t+dt from the corresponding states at t. Also, a spoke base, which has lateral and longitudinal flexibilities relative to wheel hub, is included. By adding two extra planes of spokes to the original one, the effect of tyre width is built into the model. The three planes are equally spaced across the width of the tyre. The interaction with the ground of the spokes on these three planes is used to represent that of tyre elements at different locations across the width. Analytical results show good qualitative agreement with published experimental data. This model can be used to illustrate transient tyre behaviour and in simulations in which a generic tyre will suffice.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Application of genetic algorithms for joint optimization of signal setting parameters and dynamic traffic assignment for the real network data

This paper presents the joint optimization of signal setting parameters and dynamic user equilibrium (DUE) traffic assignment for the congested urban road network. The simulation-based approach is employed to obtain the DUE condition for the case of multiple-origin multiple-destination traffic flows. The dynamic traffic assignment simulation program (DTASP), developed in C language is used to assign the traffic dynamically on the road network, whereas method of successive averages (MSA) is modified and used to arrive at the DUE condition. The artificial intelligence technique of genetic algorithms (GAs) is applied to obtain the optimal signal setting parameters and path flow distribution factor for DUE condition. The methodology developed in such a way that joint optimization of signal setting parameters with DUE is obtained. The proposed method is applied to the real network data of Fort Area of Mumbai city comprising of 17 nodes and 56 unidirectional links with 72 Origin–Destination pairs, where all the 17 nodes are signalized intersections. The traffic flow condition for the optimized signal setting parameters is considerably improved compared to the existing signal settings. The results prove that the GA is an effective technique to solve the joint optimization problem for the real network data.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.     

Influence of load and inflation pressure on the tyre rolling resistance

Tyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper test conditions in the future standardized on-road method of measuring rolling resistance. The results indicate that while an increase of load always leads to the increase of rolling resistance force, the influence on Coefficient of Rolling Resistance is more complicated and unpredictable. They also indicate that tyres with high rolling resistance are more sensitive to inflation pressure changes than low rolling resistance tyres.     

Dynamic response of offshore jacket structures under random loads

In this paper, the dynamic response of a scale model of a jacket offshore structure is investigated both theoretically and experimentally. The experiments were conducted both in air and in water. The in-water experiments were done in the towing tank of Memorial University to simulate the realistic operating conditions. The model was subjected to random wave loads. Froude's law of modeling was used to obtain the dimensions of the scale model based on the dimensions of an existing structure. The effects of varying the structure's weight, and the characteristics of the wave loading were investigated. The structure's weight was changed by adding weights to the structure's deck. A finite element model was designed to determine the dynamic response of the model. Excellent agreement between the experimental and theoretical results was obtained.The reaction force at the foundation was estimated from strain measurements and compared with the finite element calculations. Fair agreement was obtained.This work is the first stage of a project whose objective is to develop a method for structural damage detection using the free vibration response of the structure. The free vibration response will be obtained from the stationary random response of the structure using the random decrement method. Having an accurate model to describe the dynamic response of the structure is the first step in this study.     

Implementation of discharging/charging current sensorless state-of-charge estimator reflecting cell-to-cell variations in lithium-ion series battery packs

This paper offers novel insights to the design and implementation of an innovative state-of-charge (SOC) estimator for the lithium-ion (Li-Ion) series battery pack. The most interesting feature of this approach is that it can utilize information from each filtered terminal voltage of the Li-Ion cells connected in series for SOC estimation of the battery pack. Without actual sensing each discharging/charging current (DCC) applied to the Li-Ion cells, it is possible to extract each DCC estimation from the corresponding filtered terminal voltages with an equivalent electrical circuit model (EECM) identification of all Li-Ion cells in the battery pack. There are two advantages to SOC estimation of the battery pack with this approach. First, the proposal can be implemented simply and effectively, reducing the computational steps required for SOC estimation. By reducing computational steps, the proposal is expected to be more cost-effective. Second, the approach guarantees an improved SOC performance, even if the battery pack results in inevitable cell-to-cell variation among Li-Ion cells. Accordingly, there are fewer differences to previously estimated DCCs among Li-Ion cells. Specifically, all values from the estimated DCCs are properly compensated for by simultaneous parameter modification according to each cell’s electrochemical characteristics. Experimental results clearly demonstrate that our DCC sensorless SOC estimator provides robust SOC performance for the battery pack. This approach considered an experimental battery pack (12S1P) connected in series using 2.6 Ah LiCoO2 cells produced by Samsung SDI.