H_∞ Autopilot Design for Autonomous Underwater Vehicles

The design approach of H∞ autopilot for autonomous underwater vehicles (AUVs) is proposed. Comprised by the three sub-controllers,i.e. speed,heading and depth controllers,the designed autopilot has advantage over existing H∞ control of AUVs. The overshoot in speed,heading and depth control systems under step commands is restricted by refining the weighting function for robust stability. The dynamic performance of heading and depth control systems is improved by feeding back yaw rate and pitch angle,respecti...     

20世纪美国应对机动性的交通构想及高速公路发展历程

为了阐述20世纪除汽车机动性外,交通发展经历的最重要的进程——城市高速公路的出现,考察了过去100年来美国城市交通规划的历史。通过回顾各种研究资料,认为资助州际公路发展所采用的方法使联邦和州公路工程师成为主管,这影响了公路的选线及设计。联邦公路工程师只关注机动车通过效率的最大化,而在很大程度上忽略了城市的其他利害关系。没有先进的规划理念指导、过度建设、稀疏、放射环状的道路网对于加强机动性取得了极大的效益,但通常要为此付出巨大的社会和环境成本。最后指出,在实践中要重新审视具有百年历史的协调交通与土地利用规划的观点,而且,公共财政权宜之计式的政治决策方式将对工程、出行和城市形态产生深远的影响。·     

Vibration transmission reduction from a centrifugal turbo blower in a fuel cell electric vehicle

This paper presents a multi-body flexible dynamic analysis of a centrifugal turbo blower for a fuel cell electric vehicle (FCEV) based on the application of computer-aided engineering (CAE) to predict the acceleration at the mount position of the blower. This predicted acceleration is validated by using the measured acceleration data. The numerical simulation for the multi-body flexible dynamics of the blower is used not only to identify the most effective mount among four mounts in an FCEV by controlling the complex stiffness of the isolator, but also to suggest the range of complex stiffness of the isolator at the most effective mount. This numerical simulation technology can be useful for the estimation of the variation of vibration transmission for the structural modification of the turbo blower.     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

Modeling,parameter estimation and nonlinear control of automotive electronic throttle using a Rapid-Control Prototyping technique

An electronic throttle consists of a DC motor, spur gears, a return spring, a position sensor, power electronics and an electronic control unit. Fast and precise position control of this electromechanical system is relatively difficult due to very high friction and the strong nonlinearity of the spring. Simple application of linear control, such as PID, fails. In this paper, two new controller structures suitable for different reference signal types are described. The key component of the position controller is the friction compensator based on either/both feedforward or feedback principles. The quality of the resulting behavior was measured using several criteria including the measure of control activity around the equilibrium position. The control activity directly influences the vibration, the noise and the wear of the servo system. The proposed controllers demonstrated superior behavior compared with other published structures.     

Computational and experimental investigation of the unsteady flow structures around automotive outside rear-view mirrors

The unsteady flow field around two automotive outside rear-view mirrors is investigated. This study includes comprehensive experimental and computational approaches in order to characterize the complex flow structures in the wake of the mirrors. The experiments were carried out in a wind tunnel which included the measurements of the instantaneous and averaged velocity fields as well as mean and unsteady surface pressure distributions. The simulations were performed using Large Eddy Simulation (LES). The LES approach (particularly with the dynamic subgrid viscosity model) provided good agreements with the experiments for the velocity and the surface pressure distributions. The experimental and the computational results of this study will be used as a benchmark to validate the current and the future CFD development and the subsequent aero-acoustic computations.     

Design and implementation of a UPnP-can gateway for automotive environments

In this paper, we propose a universal plug and play (UPnP) — controller area network (CAN) gateway system using UPnP middleware for interoperability between external smart devices and an in-vehicle network. The proposed gateway consists of a UPnP communication device, a CAN communication device, and a device translator layer. In-vehicle devices are not usually IP-based, so we implemented an in-vehicle device manager in the UPnP communication device which is in the gateway. We developed a vehicle simulator to produce real vehicular data for performance analysis. The CAN communication device transmits and receives real-time vehicle data between the real vehicular simulator and external devices through the UPnP. The device translator layer configures a message frame for enabling seamless data input and output between the CAN and UPnP protocols. After implementation, we generated an internal-external service request and tested the result. Finally, we confirmed the service request and operation between external devices and the internal vehicular device. Additionally, for a variety of external device numbers and communication environments, we demonstrated the gateway performance by measuring the round trip time (RTT) for overall service implementation.