On the observability of the fortnightly cycle of the Tagus estuary turbid plume using MODIS ocean colour images

Using three years (2003 to 2005) of MODIS-Aqua normalized water-leaving radiance at 551 nm this paper shows a fortnightly cycle in the Tagus estuary turbid plume. The Tagus estuary is one of the largest estuaries of the west coast of Europe and is located in the most populated area of Portugal, including the capital Lisbon. The turbid plume has been detected by the backscattering characteristics of the surface waters in the vicinity of the estuary mouth. In fortnightly scales, the turbid plume has smaller dimensions during and after neap tides and higher dimensions during and after spring tides. This is most probably associated with the fortnightly spring–neap tidal cycle and the consequent increase in turbidity inside the estuary during spring tides. During the summer weak spring tides (tidal amplitude approximately 2.5 m) no turbid plume is observed for an entire fortnightly cycle. Outside the summer months, precipitation, river discharge and winds, were found to increase the turbid area, but the fortnightly cycle appears to be superimposed on the large time-scale variability, and present throughout the year.     

On the numerical accuracy of the prediction of resistance coefficients in ship stern flow calculations

This article presents a study on the accuracy of the numerical determination of the friction and pressure resistance coefficients of ship hulls. The investigation was carried out for the KVLCC2 tanker at model- and full-scale Reynolds numbers. Gravity waves were neglected, i.e., we adopted the so-called double-model flow. Single-block grids with H–O topology were adopted for all the calculations. Three eddy viscosity models were employed: the one-equation eddy viscosity and the two-equation models proposed by Menter and the TNT version of the two-equation k-ω model. Verification exercises were performed in sets of nearly geometrically similar grids with different densities in the streamwise, normal, and girthwise directions. The friction and pressure resistance coefficients were calculated for different levels of the iterative error and for computational domains of different size. The results show that on the level of grid refinement used, it is possible to calculate the viscous resistance coefficients in H–O grids that do not match the ship contour with a numerical uncertainty of less than 1%. The differences between the predictions of different turbulence models were larger than the numerical uncertainty; however, these differences tended to decrease with increases in the Reynolds number. The pressure resistance was remarkably sensitive to domain size and far-field boundary conditions. Either a large domain or the application of a viscous–inviscid interaction procedure is needed for reliable results. This work was presented in part at the International Conference on Computational Methods in Marine Engineering—MARINE 2007, Barcelona, June 3–4, 2007.     

Unsteady finite-depth effects during resistance tests on a ship model in a towing tank

This paper covers an extension of the study of Doctors et al. (J Ship Res 52(4):263–273, 2008) on oscillations in wave resistance during the constant-velocity phase of a towing-tank resistance test on a ship model to the case of relatively shallow water. We demonstrate here that the unsteady effects are very prominent and that it is essentially impossible to achieve a steady-state resistance curve in a towing tank of typical proportions for a water-depth-to-model-length ratio of 0.25. This statement is particularly true in the speed region near a depth Froude number of unity. However, on the positive side, we show here that an application of unsteady linearized wave-resistance theory provides an excellent prediction of the measured total resistance, when one accounts for the form factor in the usual manner. Finally, a simple application of the results to the planning and analysis of towing-tank tests is presented.     

Influence of the slice position on chloride migration tests for concrete in marine conditions

Chloride migration tests are used to measure the concrete capacity to inhibit chloride attack. Many researchers carry out this test in a slice of concrete extracted from the central part of cylindrical specimens, discarding about 75% of the concrete used to mold the specimens. This fact generated the question: would it be possible to extract more slices from a same specimen without losing the confidence in the results? The main purpose of this work is to answer this question. Moreover, another aim of this study was to show the difference of chloride penetration between finished faces and the formwork surfaces of concrete beams and slabs. The results indicated that it is possible to use more slices of a single specimen for a chloride migration test. Moreover, it was demonstrated that there is a significant difference of chloride penetration between the finished surface and the formwork surface of the specimens.     

A study of vibration and vibration control of ship structures

This paper examines the vibration characteristics and vibration control of complex ship structures. It is shown that input mobilities of a ship structure at engine supports, due to out-of-plane force or bending moment excitations, are governed by the flexural stiffness of the engine supports. The frequency averaged input mobilities of the ship structure, due to such excitations, can be represented by those of the corresponding infinite beam. The torsional moment input mobility at the engine support can be estimated from the torsional response of the engine bed section under direct excitation. It is found that the inclusion of ship hull and deck plates in the ship structure model has little effect on the frequency-averaged response of the ship structure. This study also shows that vibration propagation in complex ship structures at low frequencies can be attenuated by imposing irregularities to the ring frame locations in ships. Vibration responses of ship structures due to machinery excitations at higher frequencies can be controlled by structural modifications of the local supporting structures such as engine beds in ships.     

Water entry of a bow-flare ship section with roll angle

The two-dimensional water entry of a bow-flare ship section with constant roll angle, or heel angle, was studied by using a boundary element method. The fully nonlinear free surface conditions and exact body boundary conditions were satisfied. Nonviscous flow separation from the knuckles of the section or from the curved bottom could be simulated. The numerical calculations were compared with existing experimental results. First, the effects of roll angle were investigated and then the characteristics associated with large roll angles were examined in particular. The evolution of the free surfaces and the pressure distributions on the section surface are illustrated and the influence of nonviscous flow separation from the leeward section surface is discussed.     

Aggregating mobile object trajectories: cumulative time geographic density estimation for GPS data

We present new approaches that expand upon the time geographic density estimation (TGDE) framework previously employed to estimate potential path trees. In the past, TGDE metrics have identified possible locations an individual moving object may have passed between, given known origin and destination points. This paper utilizes a new form of TGDE to investigate taxicab GPS traces over a specified time horizon with position ‘gaps’. To this end, we propose a new extension to the TGDE framework, TGDE-C, which is used to determine the cumulative TGDE values for a group of GPS traces, at a given location. These metrics are applied to multiple taxis and allow for time of day analysis. Additionally, we combine these new extensions with existing TGDE metrics that allow us to determine how accessible individual or groups of vehicles are to urban opportunities.     

Property Evolution of Sulphoaluminate Grouting Material under Pressure Circulation北大核心CSCD

Water-sealed underground oil tank projects are quite different from traditional underground projects since the water-sealing conditions are very strict and the difficulties caused by the geological specificity, structural specificity and construction specificity are key factors affecting the project. In light of the significant early initial setting time and rapid temperature increase of sulphoaluminate cement-based grouting material for a large domestic water-sealed underground oil tank with pressurized cyclic grouting, a laboratory grouting simulation is conducted. It is found that the properties of the sulphoaluminate cement-based grouting material are quite different under different pressure cycles, the hydration exothermic peak time gets shorter with an increase of circulation time, the compressive strength decreases with an increase of circulation time, and the longer the circulation time the more obvious the de-crease of compressive strength. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Numerical Simulation of Advanced Geological Forecasting Based on Multi- Source Seismic Interferometry北大核心CSCD

For existing advanced geological forecasting, the forecast distance is short and the test frequency is high, increasing test and construction risks. Since various methods have different requirements for the test environ-ment, preparation work can be tedious and result in a long construction time thereby affecting normal construction.A new advanced geological forecast technique based on multi-source seismic interferometry for tunnels is proposed.This technique uses the blast at one end of tunnel as a centrum and receives the signal at the other end of the tun-nel, therefore allowing advanced geological forecasting of the unexcavated tunnel part by relative processing and im-aging. A numerical simulation of this kind of geological forecasting using the finite difference method to simulate two kinds of unfavorable geological bodies (karst and a fault) predicted them accurately and verified the effective-ness and accuracy of this geological forecasting method. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis of Ground Response and Structure Stress Induced by PBA Method北大核心CSCD

The application of prefabricated tunnel technology has been become a new research field both in China and abroad. Based on the running tunnel between Yufuhe station and Wangfuzhuang station of Jinan rail transit line R1, a new prefabricated tunnel construction technology, the PBA method is presented. This paper makes a detailed discussion on section form, supporting scheme and construction process of the PBA method. In this study, 3D a new 3D numerical model for PBA method is presented by finite difference numerical simulation software Flac and the construction processes are modeled. The rule of ground surface settlement, ground deformation and structural stress caused by PBA method is studied in detail. Results show that the structure of PBA method can effectively control the deformation magnitude and scope. Stress concentration appears at the prefabricated connection parts and the reinforcement needs to check. The total assembled structure forms the load-bearing system after the completion of the lateral wall. The built-in depth of the precast pile and pile bottom grouting quality should to be ensured to control the displacement of the precast piles. The results of this study will be a useful reference for similar projects in the future. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.