Disturbance Observer-Based Sideslip Angle Control for Improving Cornering Characteristics of In-Wheel Motor Electric Vehicles

In this paper, a robust sideslip angle controller based on the direct yaw moment control (DYC) is proposed for in-wheel motor electric vehicles. Many studies have demonstrated that the DYC is one of the effective methods to improve vehicle maneuverability and stability. Previous approaches to achieve the DYC used differential braking and active steering system. Not only that, the conventional control systems were commonly dependent on the feedback of the yaw rate. In contrast to the traditional control schemes, however, this paper proposes a novel approach based on sideslip angle feedback without controlling the yaw rate. This is mainly because if the vehicle sideslip angle is controlled properly, the intended sideslip angle helps the vehicle to pass through the corner even at high speed. On the other hand, the vehicle may become unstable because of the too large sideslip caused by unexpected yaw disturbances and model uncertainties of time-varying parameters. From this aspect, disturbance observer (DOB) is employed to assure robust performance of the controller. The proposed controller was realized in CarSim model described actual electric vehicle and verified through computer simulations.     

A fundamental investigation of tilt control systems for narrow commuter vehicles

One way of addressing traffic congestion is by efficiently utilizing the existing highway infrastructure. Narrow tilting vehicles that need a reduced width lane can be part of the solution if they can be designed to be safe, stable, and easy to operate. In this paper, a control system that stabilizes the tilt mode of such a vehicle without affecting the handling of the vehicle is proposed. This control system is a combination of two different types of control schemes known as steering tilt control (STC) and direct tilt control (DTC) systems. First, different existing variations of both STC and DTC systems are considered and their shortcomings analysed. Modified control schemes are then suggested to overcome the deficiencies. Then a new method of integrating these two control schemes that guarantees smooth switchover between the controllers as a function of vehicle velocity is proposed. The performance of the proposed STC, DTC, and integrated systems is evaluated by carrying out simulations for different operating conditions and some experimental work. The design of a second-generation narrow tilting vehicle on which the developed control system has been implemented is presented.     

Improving the predictiveness of the quasi-d combustion model for spark ignition engines with flexible intake systems

Fast and predictive simulation tools are prerequisites for pursuing simulation based engine control development. A particularly attractive tradeoff between speed and fidelity is achieved with a co-simulation approach that marries a commercial gas dynamic code WAVE™ with an in-house quasi-dimensional combustion model. Gas dynamics are critical for predicting the effect of wave action in intake and exhaust systems, while the quasi-D turbulent flame entrainment model provides sensitivity to variations of composition and turbulence in the cylinder. This paper proposes a calibration procedure for such a tool that maximizes its range of validity and therefore achieves a fully predictive combustion model for the analysis of a high degree of freedom (HDOF) engines. Inclusion of a charge motion control device in the intake runner presented a particular challenge, since anything altering the flow upstream of the intake valve remains “invisible” to the zero-D turbulence model applied to the cylinder control volume. The solution is based on the use of turbulence multiplier and scheduling of its value. Consequently, proposed calibration procedure considers two scalar variables (dissipation constant C _β and turbulence multiplier C _M ), and the refinements of flame front area maps to capture details of the spark-plug design, i.e. the actual distance between the spark and the surface of the cylinder head. The procedure is demonstrated using an SI engine system with dual-independent cam phasing and charge motion control valves (CMCV) in the intake runner. A limited number of iterations led to convergence, thanks to a small number of adjustable constants. After calibrating constants at the reference operating point, the predictions are validated for a range of engine speeds, loads and residual fractions.     

Model-based design of a variable nozzle turbocharger controller

Variable Nozzle Turbocharger (VNT) was invented to solve the problem of matching an ordinary turbocharger with an engine. VNT can harness exhaust energy more efficiently, enhance intake airflow response and reduce engine emissions, especially during transient operating conditions. The difficulty of VNT control lies in how to regulate the position of the nozzle at different engine working conditions. The control strategy designed in this study is a combination of a closed-loop feedback controller and an open-loop feed-forward controller. The gain-scheduled proportional-integral-derivative (PID) controller was implemented as the feedback controller to overcome the nonlinear characteristic. As it is difficult to tune the parameters of the gain-scheduled PID controller on an engine test bench, system identification was used to identify the plant model properties at different working points for a WP10 diesel engine on the test bench. The PID controller parameters were calculated based on the identified first-order-plus-dead-time (FOPDT) plant model. The joint simulation of the controller and the plant model was performed in Matlab/Simulink. The time-domain and frequency-domain performances of the entire system were evaluated. The designed VNT control system was verified with engine tests. The results indicated that the real boosting pressure traced the target boosting pressure well at different working conditions.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

巡回出租车市场卫星派遣车队最适规模之研究

出租车乃公共运输系统中最具经营弹性之运输工具,在经济活动频繁之都会地区广为旅行者所欢迎。近年,由于信息与通讯科技的发展,以及日益增高的行车成本,应用卫星派遣俨然已成为出租车市场的趋势与潮流。研究以双层规划数学分析模型描述巡回暨卫星派遣出租车市场之营运绩效,考虑社会福利最大与营运者利润最大的双阶层目标,研析最适车队规模和卫星派遣出租车比例,并针对使用卫星派遣服务之乘客数量,分析出租车市场结构的变化。     

Performance optimization of CVT for two-wheeled vehicles

Continuously Variable Transmission (CVT) is one of the most promising automotive transmission technologies because of its continuously variable gear ratio and reduced shift shock. CVT is different from Manual Transmission and Automatic Transmission, and it is possible to operate the power source in its high efficiency region with CVT in the drive train. Several types of CVT exist that can be categorized based on the mechanism of power transmission, such as the belt pulley, traction drive, and hydrostatic types. This paper investigates the belt pulley CVT, which consists of a thrust actuator, driver pulley, belt, driven pulley, and preload spring of the output shaft. A complete CVT is constructed, and based on that a simulation program that analyzes the static performance of a CVT is implemented in Matlab/Simulink. From these simulation results, methods for improving the efficiency of the CVT are discussed. The coefficient of the torque capacity factor is proposed as affecting the matching between a power source and a CVT, and methods for improving the matching effect are also investigated.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.     

Model-based analysis of the mechanical subsystem of an air brake system

Most commercial vehicles such as buses and trucks use an air brake system, often equipped with an S-cam drum brake, to reduce their speed and/or to stop. With a drum brake system, the clearance between the brake shoe/pad and the brake drum may increase because of various reasons such as wearing of the brake shoe and/or brake drum and drum expansion caused by high heat generation during the braking process. Hence, to ensure proper functioning of the brake system, it is essential that the clearance between the brake shoe and the brake drum is monitored. In this paper, we present a mathematical model for the mechanical subsystem of the air brake system that can be used to monitor this clearance. This mathematical model correlates the push rod stroke transients and the brake chamber pressure transients. A kinematic analysis and a dynamic analysis of the mechanical subsystem of the air brake system were performed, and the results are corroborated with experimental data.     

Engine performance and toxic gas analysis of biobutanol-blended gasoline as a vehicle fuel

A comprehensive study evaluating the performance of biobutanol-blended gasoline in passenger cars was conducted because biobutanol is considered a better biofuel than bioethanol as it has no water solubility and it has a higher caloric value, giving it a higher energy value. Several kinds of samples—suboctane gasoline, 8 volume percentage and 16 volume percentage biobutanol—blended gasoline, and a 10 volume percentage MTBE-blended market sample (as the oxygencontaining gasoline)-were tested to evaluate the engine performance in terms of the detergency of the intake valves and combustion chambers, power, emissions, and fuel efficiency. Additionally, the toxicity of the emissions from these biobutanolblended samples was tested in order to assess the viability of biobutanol as one of the competitive potential substitutes for MTBE as an oxygenator in the near future. The results show that biobutanol-blended gasoline samples had relatively better detergency, relatively higher power, and similar levels of emissions compared with those of MTBE-blended gasoline. Formaldehyde was emitted from all of the samples at almost the same levels and within the error range, whereas biobutanolblended gasoline samples emitted approximately three times the amount of acetaldehyde than did the suboctane gasoline. This study shows that biobutanol is one of the best alternative bioalcohol fuels for use in the near future.