Cycle-simulation turbulence modelling of IC engines

Numerical simulations of IC engines are of high interest for automotive engineers worldwide. The simulation models should be as fast as possible, low-computational effort and predictive tool. The correct prediction of turbulence level inside the combustion chamber of spark ignition engines is the most important factor influencing to the engine working cycle. This paper presents a development of the k-ε turbulence model applied to the commercial cycle-simulation software with the high emphasis on the intake part. The validation was performed on two engine geometries with the variation of engine speed and load comparing the cycle-simulation results of the turbulent kinetic energy and in-cylinder temperature with 3-D CFD results. In order to apply the cycle-simulation turbulence model for the simulation of entire engine map, the parameterization model of turbulence constants was proposed. The parameterized turbulence model was optimized using NLPQL optimization algorithm where the single set of turbulence model parameters for each engine was found. A good agreement of the turbulent kinetic energy during the expansion was achieved when the turbulence affects the flame front propagation and combustion rate as well.     

Fast passenger ferries and their future

This papers examines the different choices of High Speed Craft (HSC) hull design available and briefly looks at the advantages and disadvantages of each hull form. The trends in various design aspects of HSC such as speed, capacity and size are studied. An investigation on the HSC development is conducted and the future of HSC in the UK is studied. A study onboard an HSC with the aim of trying to determine what passengers think of HSC and why they travel by them is also conducted. Finally, an analysis of the possible market for HSC is carried out.     

Origin–destination table disaggregation using biproportional least squares estimation

This paper describes a group of techniques for disaggregating origin–destination tables for travel forecasting that makes explicit use of observed traffic on a network. Five models within the group are presented, each of which uses nonlinear least-squares estimation to obtain row and column factors for splitting trip totals from and to larger geographical areas into smaller ones. The techniques are philosophically similar to Fratar factoring, although the solution method is quite different. The techniques are tested on a full-sized network for Northfield, MN and are found to work effectively.     

Efficiency and ecological characteristics of a VCR diesel engine

Compression ratio (CR) is a design parameter with highest influence on efficiency, emission and engine characteristics. In conventional internal combustion (IC) engines, the compression ratio is fixed and their performance is, therefore, a compromise between conflicting requirements. One fundamental problem is that drive units in the vehicles must successfully operate at variable speed and loads and in different ambient conditions. If a diesel engine has a fixed CR, a minimal value must be chosen that can achieve a reliable self-ignition when starting the engine in cold start conditions. In diesel engines, variable compression ratio (VCR) provides control of peak cylinder pressure, improves cold start ability and low load operation, enabling the multi-fuel capability, increase of fuel economy and reduction of emissions. By application of VCR and other mechanisms, the optimal regime fields are extended to the prime requirements: consumption, power, emission, noise, etc., and/or the possibility of the engine to operate with different fuels is extended. An experimental Diesel engine has been developed at the Faculty of Engineering, University of Kragujevac. The changes of CR are realized by changing the piston chamber diameter. Detailed engine tests were performed at the Laboratory for IC engines. Special attention has been given to decrease of fuel consumption and exhaust emissions. An optimal field of CR variation has been determined depending on the given objectives: minimal fuel consumption, minimal nitric oxides, and particulate matter emissions, etc.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.     

A Multi-Spoke, Three Plane Tyre Model for Simulation of Transient Behaviour

Based on the multi-spoke, single-plane, steady-state tyre model, a transient multi-spoke, three-plane tyre model is presented. This model involves updating the states of all the spokes under consideration to t+dt from the corresponding states at t. Also, a spoke base, which has lateral and longitudinal flexibilities relative to wheel hub, is included. By adding two extra planes of spokes to the original one, the effect of tyre width is built into the model. The three planes are equally spaced across the width of the tyre. The interaction with the ground of the spokes on these three planes is used to represent that of tyre elements at different locations across the width. Analytical results show good qualitative agreement with published experimental data. This model can be used to illustrate transient tyre behaviour and in simulations in which a generic tyre will suffice.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Influence of vehicular traffic on urban air quality – A case study of Hyderabad,India

In the present study, impact of vehicular traffic emissions on black carbon aerosol mass concentration, trace gases and ground reaching solar radiation were analyzed during nationwide truck strike of 5–12 January, 2009 over urban environment of Hyderabad, India. A significant reduction of about 57%, 60%, 40% and 50% was observed in black carbon, particulate matter, carbon monoxide and ozone respectively during nationwide truck strike period. Results of the study are important for source apportionment of pollutants as the strike created natural laboratory for studying the impact of diesel operated trucks on urban air quality.     

Application of genetic algorithms for joint optimization of signal setting parameters and dynamic traffic assignment for the real network data

This paper presents the joint optimization of signal setting parameters and dynamic user equilibrium (DUE) traffic assignment for the congested urban road network. The simulation-based approach is employed to obtain the DUE condition for the case of multiple-origin multiple-destination traffic flows. The dynamic traffic assignment simulation program (DTASP), developed in C language is used to assign the traffic dynamically on the road network, whereas method of successive averages (MSA) is modified and used to arrive at the DUE condition. The artificial intelligence technique of genetic algorithms (GAs) is applied to obtain the optimal signal setting parameters and path flow distribution factor for DUE condition. The methodology developed in such a way that joint optimization of signal setting parameters with DUE is obtained. The proposed method is applied to the real network data of Fort Area of Mumbai city comprising of 17 nodes and 56 unidirectional links with 72 Origin–Destination pairs, where all the 17 nodes are signalized intersections. The traffic flow condition for the optimized signal setting parameters is considerably improved compared to the existing signal settings. The results prove that the GA is an effective technique to solve the joint optimization problem for the real network data.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.