全文获取类型
收费全文 | 2209篇 |
免费 | 22篇 |
专业分类
公路运输 | 871篇 |
综合类 | 71篇 |
水路运输 | 572篇 |
铁路运输 | 41篇 |
综合运输 | 676篇 |
出版年
2023年 | 19篇 |
2022年 | 39篇 |
2021年 | 12篇 |
2020年 | 7篇 |
2019年 | 18篇 |
2018年 | 92篇 |
2017年 | 94篇 |
2016年 | 172篇 |
2015年 | 22篇 |
2014年 | 89篇 |
2013年 | 278篇 |
2012年 | 117篇 |
2011年 | 179篇 |
2010年 | 167篇 |
2009年 | 108篇 |
2008年 | 148篇 |
2007年 | 79篇 |
2006年 | 41篇 |
2005年 | 30篇 |
2004年 | 38篇 |
2003年 | 22篇 |
2002年 | 24篇 |
2001年 | 24篇 |
2000年 | 34篇 |
1999年 | 27篇 |
1998年 | 16篇 |
1997年 | 26篇 |
1996年 | 28篇 |
1995年 | 33篇 |
1994年 | 13篇 |
1993年 | 17篇 |
1992年 | 18篇 |
1991年 | 16篇 |
1990年 | 8篇 |
1988年 | 13篇 |
1987年 | 7篇 |
1986年 | 11篇 |
1985年 | 18篇 |
1984年 | 9篇 |
1983年 | 10篇 |
1982年 | 9篇 |
1981年 | 9篇 |
1980年 | 11篇 |
1979年 | 11篇 |
1978年 | 11篇 |
1977年 | 11篇 |
1976年 | 9篇 |
1975年 | 13篇 |
1974年 | 8篇 |
1973年 | 6篇 |
排序方式: 共有2231条查询结果,搜索用时 15 毫秒
121.
Compression ratio (CR) is a design parameter with highest influence on efficiency, emission and engine characteristics. In conventional internal combustion (IC) engines, the compression ratio is fixed and their performance is, therefore, a compromise between conflicting requirements. One fundamental problem is that drive units in the vehicles must successfully operate at variable speed and loads and in different ambient conditions. If a diesel engine has a fixed CR, a minimal value must be chosen that can achieve a reliable self-ignition when starting the engine in cold start conditions. In diesel engines, variable compression ratio (VCR) provides control of peak cylinder pressure, improves cold start ability and low load operation, enabling the multi-fuel capability, increase of fuel economy and reduction of emissions. By application of VCR and other mechanisms, the optimal regime fields are extended to the prime requirements: consumption, power, emission, noise, etc., and/or the possibility of the engine to operate with different fuels is extended. An experimental Diesel engine has been developed at the Faculty of Engineering, University of Kragujevac. The changes of CR are realized by changing the piston chamber diameter. Detailed engine tests were performed at the Laboratory for IC engines. Special attention has been given to decrease of fuel consumption and exhaust emissions. An optimal field of CR variation has been determined depending on the given objectives: minimal fuel consumption, minimal nitric oxides, and particulate matter emissions, etc. 相似文献
122.
123.
V. Alkan S. M. Karamihas G. Anlas 《International Journal of Automotive Technology》2011,12(4):529-535
To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical
stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented
independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given
to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model
agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed
under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical
static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply
constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire,
which is directly related to fuel consumption and tire tread life. 相似文献
124.
125.
J. Zhou Jy Wong R. S. Sharp 《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》1999,31(1):35-45
Based on the multi-spoke, single-plane, steady-state tyre model, a transient multi-spoke, three-plane tyre model is presented. This model involves updating the states of all the spokes under consideration to t+dt from the corresponding states at t. Also, a spoke base, which has lateral and longitudinal flexibilities relative to wheel hub, is included. By adding two extra planes of spokes to the original one, the effect of tyre width is built into the model. The three planes are equally spaced across the width of the tyre. The interaction with the ground of the spokes on these three planes is used to represent that of tyre elements at different locations across the width. Analytical results show good qualitative agreement with published experimental data. This model can be used to illustrate transient tyre behaviour and in simulations in which a generic tyre will suffice. 相似文献
126.
The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods. 相似文献
127.
Anu Rani Sharma Shailesh Kumar Kharol K.V.S. Badarinath 《Transportation Research Part D: Transport and Environment》2010,15(3):154-159
In the present study, impact of vehicular traffic emissions on black carbon aerosol mass concentration, trace gases and ground reaching solar radiation were analyzed during nationwide truck strike of 5–12 January, 2009 over urban environment of Hyderabad, India. A significant reduction of about 57%, 60%, 40% and 50% was observed in black carbon, particulate matter, carbon monoxide and ozone respectively during nationwide truck strike period. Results of the study are important for source apportionment of pollutants as the strike created natural laboratory for studying the impact of diesel operated trucks on urban air quality. 相似文献
128.
This paper presents the joint optimization of signal setting parameters and dynamic user equilibrium (DUE) traffic assignment for the congested urban road network. The simulation-based approach is employed to obtain the DUE condition for the case of multiple-origin multiple-destination traffic flows. The dynamic traffic assignment simulation program (DTASP), developed in C language is used to assign the traffic dynamically on the road network, whereas method of successive averages (MSA) is modified and used to arrive at the DUE condition. The artificial intelligence technique of genetic algorithms (GAs) is applied to obtain the optimal signal setting parameters and path flow distribution factor for DUE condition. The methodology developed in such a way that joint optimization of signal setting parameters with DUE is obtained. The proposed method is applied to the real network data of Fort Area of Mumbai city comprising of 17 nodes and 56 unidirectional links with 72 Origin–Destination pairs, where all the 17 nodes are signalized intersections. The traffic flow condition for the optimized signal setting parameters is considerably improved compared to the existing signal settings. The results prove that the GA is an effective technique to solve the joint optimization problem for the real network data. 相似文献
129.
Development of hot stamped center pillar using form die with channel type indirect blank holder 总被引:1,自引:0,他引:1
H. S. Choi B. M. Kim K. J. Nam S. Y. Ha S. H. Cha C. G. Kang 《International Journal of Automotive Technology》2011,12(6):887-894
The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase
passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed
using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to
develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type
of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after
the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding
force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner
radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known
that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel,
and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a
form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture. 相似文献
130.
S. Soylu 《International Journal of Automotive Technology》2014,15(3):369-376
Engine load-speed frequency map of a hybrid city bus, which operates on the routes of Sakarya Municipality, was compared with that of European Transient Cycle (ETC) and World Harmonized Transient Cycle (WHTC), which are the certification test cycles. It was observed that the hybrid city bus engine operates mostly at three main regions, which are idling (30% load and 750 rpm), motoring (0% load and 1200 rpm) and high load (80% load and 1800 rpm) conditions under real world urban driving conditions. However, engine load-speed frequency maps of the certification test cycles are significantly different and cannot represent the real world urban driving conditions of the hybrid city bus. Therefore, the Particle Number (PN) emissions of the hybrid city bus were investigated under real world urban driving conditions. The aims of work were to examine the effects of city bus hybridization on the particle emissions and develop PN emission factors. The PN concentrations and size distributions together with engine operating conditions were measured with a Particle Measurement Program (PMP) compliant system, which involves a condensation particle counter (CPC) and a particle sizer (EEPS). The measurements under real world urban driving conditions indicated that the emission factors of the hybrid city bus for the PN and Total PN are 8.99E+12 and 2.51E+13 #/kW-h, respectively. The PN size distribution measurements indicated that the particles up to approximately 20 nm are not very sensitive to changes in engine power and they are exist even during motoring conditions. But, the particles in the size range from 20 to 200 nm are very sensitive to sudden changes of the engine power. 相似文献