Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Development of a navigation algorithm with dead reckoning for unmanned ground vehicles

A navigation algorithm is indispensable for Unmanned Ground Vehicles (UGVs). During driving, UGVs follow a global path. In this study, we propose a navigation algorithm using Real Time Kinematic (RTK)-Differential Global Positioning System (DGPS) units and encoders to complement global path planning. Sometimes GPS systems lose their signals and receive inaccurate position data due to many factors, such as edifice and barrier obstructions. This paper shows that GPS deviations can be solved using a Dead Reckoning (DR) navigation method with encoders and that position errors can be decreased through the use of RTK-DGPS units. In addition to this method, we will introduce a new waypoint update algorithm and a steering algorithm using RTK-DGPS units.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

License plate extraction method for identification of vehicle violations at a railway level crossing

The primary cause of most railroad accidents is vehicle entry into railway level crossings despite warning messages. To identify drivers who violate railway level crossing regulations, vehicle license plate recognition can be applied at railway level crossings. The purpose of this paper is to present an effective method for extracting the license plate region from vehicle images taken at railway level crossings. The method proposed in this paper uses the variation in the gray-level values across the image of a license plate. For license plate region extraction, the character region is first recognized by identifying the character width and the difference between the background region and the character region. The license plate region is then extracted by finding the inter-character distance in the plate region. In addition, the license plate type is identified by the difference in the gray-level value between the background region and the character region. The proposed method is effective in solving the current challenges in extracting the license plate region from the damaged frames of license plates issued for domestic use, including new types of license plates. According to the experimental results, the proposed method yields a high extraction rate of 99.5% for vehicle license plates.     

Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.     

Altimeter assimilation in the OCCAM global model: Part I: A twin experiment

An altimeter data assimilation scheme has been tested in the OCCAM (Ocean Circulation and Climate Advanced Modelling) global 1/4°, 36-level model using a twin experiment format. The Cooper and Haines displacement scheme is used. The method works well in most regions and depths. Currents and densities in the top 1000 m generally improve by over 50–70% after 5 months of sea level assimilation every 15 days. Below 1000 m, an error reduction of up to 50% is achieved. The errors remain low during a further 60-day run without assimilation. Diagnostics for the North Atlantic, the Tropical Pacific and the Antarctic Circumpolar Current are shown alongside the global averages.The main problems encountered were in weakly stratified regions of the Antarctic and Arctic seas. A scale selective filter is developed to avoid assimilating scales much larger than the local deformation radius, and this avoids the adverse assimilation effects in the southern oceans. A companion paper uses this scheme to assimilate TOPEX and ERS-1 altimeter maps.     

Further study on the ultimate strength analysis of spherical pressure hulls

From a comparative study it is concluded that current design rules for the spherical pressure hull of manned submersible need to be updated and unified. In this paper, a series of spherical pressure hulls are calculated by nonlinear FEM. Based on these numerical results, the influence of critical arch length and the relationship of ultimate strength with t/R and structural imperfection are studied. Finally, empirical formulae for the ultimate strength of the titanium alloy spherical pressure hull of deep manned submersible based on numerical computations are given. The formulae can be used as the core equations to update current design rules.     

Shipping and investment incentives: a trilogy Part 2. Investment incentives for shipping

This paper concentrates on the shipping industry and considers the forms of fiscal and financial incentives which are used by different governments to promote or encourage investment in their shipping industry. The analysis reduces the various packages of investment incentives and loan arrangements to a common measurement—the net present value of the package—and uses this to draw international comparisons and rankings. The results are based on different values of rates of return in the shipping industry and under certain assumptions concerning the rate of inflation and the rate of discount. Differences in loan arrangements have also been incorporated. The particular results are valid only for the specified circumstances but the methodology is generally applicable.     

Use of a probabilistic particle tracking model to simulate the Prestige oil spill

A probabilistic particle tracking model is used to simulate the oil dispersion after the Prestige wreckage. This oil spill constitutes a suitable benchmark to analyze the capabilities of a probabilistic model, since the time elapsed from wreckage to oil landing (12 days) is much longer than the reliability time associated with forecast winds, usually on the order of 3–4 days. The particle model can be run in two different modes: real time mode (when existing reliable wind fields for the event under scope) and in probabilistic mode (in absence of reliable wind fields but with historical fields corresponding to a similar period). The validity of the particle model is first evaluated in a hindcast way, running the Prestige case with the wind fields corresponding to the period November 19 to November 30, 2002, which were not available at the moment of the wreckage. Calculations show the accuracy of the model to provide the right impact point and timing. The probabilistic model is then used to simulate the same event by means of historical data. The region where the oil landed is shown to be the area with the highest probability to be impacted.