Multiaxial stress creep rupture mechanisms of AZ31 magnesium alloy

The maximum principal stresses, von Mises effective stresses and principal facet stresses at the time of creep rupture were compared in uniaxial, biaxial, and triaxial stress states for AZ31 magnesium alloy. The creep rupture of this alloy was experimentally controlled by cavitation, which was the result of a low damage tolerance, λ. Creep deformation could be correlated with the von Mises effective stress parameter. The failure-mechanism control parameter governing the stress state coincided with the experimental results of the rupture of the materials under multiaxial stress states. Finally, the theoretical prediction based on constrained cavity growth and continuous nucleation agreed with the experimental rupture data to within a factor of three.     

Effect of rear slant angle on vehicle crosswind stability simulation on a simplified car model

It is important to know the effect of the aerodynamic forces and moments on driving stability because it is responsible for the excitation and influences the response of the vehicle. The purpose of this paper is to study the effect of rear slant angle of a surface vehicle on crosswind sensitivity for stability analysis. The vehicle mathematical model used to conduct a dynamic simulation was based on a simple reduced order lateral dynamics of sideslip and yaw rate motion coupled with aerodynamics model. The intention here is to compare the effect of rear slant angles response to crosswind and to rank the crosswind sensitivity ratings. The aerodynamic loads are defined as the function of the aerodynamic derivatives from the static wind tunnel tests. Result shows a 20° rear slant angle demonstrates the highest rating of crosswind sensitivity, while zero degree slant exhibits the least.     

Improving pollutant emissions in diesel engines for heavy-duty transportation using retarded intake valve closing strategies

A combined theoretical and experimental study has been carried out to determine the real potential of reducing pollutant emissions in a HD diesel engine by means of retarding the intake valve closing. The effects produced by this alteration of the basic operation cycle have been examined by a preliminary modelling study, and from the obtained results, a modified camshaft was manufactured with a delayed intake valve closing of 60 crank angle degrees. Single-cylinder engine tests were carried out with this modified camshaft, and the emissions and fuel consumption were recorded. The results showed that the retarded intake valve closing can enhance the premixed combustion phase, and thus simultaneously reduce soot and NOx emissions. Moreover, the combustion process attained is extremely tolerant to exhaust gas recirculation, and by adoption of this measure, Euro-5 emissions limits can be achieved at the tested conditions without after-treatment.     

Spatial fisheries ecology: Recent progress and future prospects

We review recent progresses made in the study of fish distribution and survival over space — i.e., fisheries spatial ecology. This is achieved by first surveying the most common statistical approaches and relative challenges associated with the analysis of fisheries spatial data, loosely grouped in geostatistical and regression approaches. Then we review a selected number of case-studies implementing the discussed techniques. We conclude by proposing new areas of statistical and ecological research to further our understanding of how fish distribute and survive in space. This review serves a dual purpose by emphasizing the scientific importance of studying spatial interactions to better understand the temporal dynamics of fish abundance, and by promoting the development of new analytical and ecological approaches for the analysis of spatial data. Through our survey we cover different statistical techniques, marine ecosystems and life stages. This analytical, geographic and ontogenetic variety is also purposely selected to highlight the importance of comparative and multidisciplinary studies across diverging ecological disciplines, ecosystems and life stages. Besides having a general ecological relevance this review also bears a more applied significance, owing to the increasing need for protecting renewable marine resources along with their primary habitat.     

Torque characteristics analysis for optimal design of a copper-layered eddy current brake system

An enhanced parametric model for a copper-layered eddy current electric machine (retarder) is introduced in this paper. The modeled torque characteristics of the copper-layered electromagnetic retarders are based on the results from a detailed electromagnetic finite element analysis (FEA) of these eddy current machines. The model uses a parameterized double-exponential function to model the steady state speed-torque characteristics of the retarder. The parameters are adjusted for optimal braking performance in conjunction with predicted speed-torque characteristics of a copper-layered retarder. A full vehicle model, along with the proposed retarder speed-torque model has been used to simulate a series braking events. The simulation results show that the peaks of the retarder speed-torque curves must be designed to occur within a specific range of speeds for optimal braking performance.     

Improving the predictiveness of the quasi-d combustion model for spark ignition engines with flexible intake systems

Fast and predictive simulation tools are prerequisites for pursuing simulation based engine control development. A particularly attractive tradeoff between speed and fidelity is achieved with a co-simulation approach that marries a commercial gas dynamic code WAVE™ with an in-house quasi-dimensional combustion model. Gas dynamics are critical for predicting the effect of wave action in intake and exhaust systems, while the quasi-D turbulent flame entrainment model provides sensitivity to variations of composition and turbulence in the cylinder. This paper proposes a calibration procedure for such a tool that maximizes its range of validity and therefore achieves a fully predictive combustion model for the analysis of a high degree of freedom (HDOF) engines. Inclusion of a charge motion control device in the intake runner presented a particular challenge, since anything altering the flow upstream of the intake valve remains “invisible” to the zero-D turbulence model applied to the cylinder control volume. The solution is based on the use of turbulence multiplier and scheduling of its value. Consequently, proposed calibration procedure considers two scalar variables (dissipation constant C _β and turbulence multiplier C _M ), and the refinements of flame front area maps to capture details of the spark-plug design, i.e. the actual distance between the spark and the surface of the cylinder head. The procedure is demonstrated using an SI engine system with dual-independent cam phasing and charge motion control valves (CMCV) in the intake runner. A limited number of iterations led to convergence, thanks to a small number of adjustable constants. After calibrating constants at the reference operating point, the predictions are validated for a range of engine speeds, loads and residual fractions.     

Hydrographic conditions affecting two fishing grounds of Mallorca island (Western Mediterranean): during the IDEA Project (2003–2004)

This paper describes the hydrographic conditions observed during six surveys carried out during 2003 and 2004, in the framework of the “IDEA Project” (acronym for “Influence of oceanographic structure and dynamics on demersal populations in waters of the Balearic Islands”). The surveys were developed on the shelf and slope of Mallorca Island, in particular in two fishing grounds at the north and south of the Mallorca channel. Periodic movements of the fishing fleet between these two areas have been regularly reported, suggesting a seasonal variability of the resources which could be in turn associated with the hydrodynamic variability. With this motivation, water masses affecting these grounds have been identified and their seasonal variability has been studied. Different oceanographic and environmental conditions have been found between the two fishing grounds. These differences are related to the presence of mesoscale structures, associated with the Western Mediterranean Intermediate Water (WIW) at the north of the Ibiza channel and big gyres detached from the Algerian Current. The former has been shown to have influence on the regional oceanic circulation and the latter could affect the progress of fresh Atlantic Water (AW) towards the channels and make possible the presence of high salinity values at intermediate waters at the south of Mallorca Island. Historical data from other oceanographic cruises carried out in the region are finally used to discuss the interannual variability of these mesoscale structures.     

Combustion development of a Bi-Fuel engine

Environmental improvement and energy issues are increasingly becoming more important as worldwide concerns. Natural gas is a good alternative fuel that can help to improve these issues because of its large quantity and clean burning characteristics. This paper provides the experimental performance results of a Bi-Fuel engine that uses Compressed Natural Gas as its Primary fuel and gasoline as its secondary fuel. This engine is a modification of the basic 1.4-liter gasoline engine. Generally, on the unmodified base engine, torque and power for CNG fuel are considerably lower than gasoline fuel. In this paper, the influence of fuels on wall temperature, performance and emissions are investigated.     

Perturbation/correlation based optimal internal combustion engine tuning

This paper addresses the application of the perturbation/correlation method to optimizing the torque output of internal combustion engines. This application was inspired by observations of the limitations in current techniques of the automotive performance tuning industry. Performance issues such as errors from true optimum spark timing and fuel injector pulse width values as well as convergence were considered for optimal tuning. The ability of the system to deal with engine cycle-to-cycle variations and their effect on input parameters is also analyzed.