Improving Tidal Turbine Performance Through Multi-Rotor Fence Configurations

Constructive interference between tidal stream turbines in multi-rotor fence configurations arrayed normally to the flow has been shown analytically, computationally, and experimentally to enhance turbine performance. The increased resistance to bypass flow due to the presence of neighbouring turbines allows a static pressure difference to develop in the channel and entrains a greater flow rate through the rotor swept area. Exploiting the potential improvement in turbine performance requires that turbines either be operated at higher tip speed ratios or that turbines are redesigned in order to increase thrust. Recent studies have demonstrated that multi-scale flow dynamics, in which a distinction is made between device-scale and fence-scale flow events, have an important role in the physics of flow past tidal turbine fences partially spanning larger channels. Although the reduction in flow rate through the fence as the turbine thrust level increases has been previously demonstrated, the within-fence variation in turbine performance, and the consequences for overall farm performance, is less well understood. The impact of turbine design and operating conditions, on the performance of a multi-rotor tidal fence is investigated using Reynolds-Averaged Navier-Stokes embedded blade element actuator disk simulations. Fences consisting of four, six, and eight turbines are simulated, and it is demonstrated that the combination of device- and fence-scale flow effects gives rise to cross-fence thrust and power variation. These cross-fence variations are also a function of turbine thrust, and hence design conditions, although it is shown simple turbine control strategies can be adopted in order to reduce the cross-fence variations and improve overall fence performance. As the number of turbines in the fence, and hence fence length, increases, it is shown that the turbines may be designed or operated to achieve higher thrust levels than if the turbines were not deployed in a fence configuration.

     

Happy today,satisfied tomorrow: emotion—satisfaction dynamics in a multi-week transit user smartphone survey

Transportation - Travel well-being encompasses three dimensions: cognitive satisfaction judgments, positive emotions, and negative emotions. Most previous literature on transit users focused either...     

Carsharing in Switzerland: identifying new markets by predicting membership based on data on supply and demand

Transportation - This study examines the relationship between the supply and demand variables that determine the probability of individuals joining a carsharing organization, using data from the...     

水平小净距隧道中夹岩安全系数法研究与应用北大核心CSCD

中夹岩柱是小净距隧道围岩稳定控制的关键部位,判别中夹岩的安全性是工程设计和施工过程中的重难点。文章通过分析不同围岩级别、埋深情况下中夹岩的破坏模式,建立Ⅳ级围岩条件下水平小净距隧道中夹岩力学分析模型,并确定中夹岩破裂面位置。根据中夹岩上部滑块体形状的不同分为两种情况,通过边坡稳定性原理、极限平衡假设及普氏压力拱理论推导中夹岩上部滑块体的抗滑力、下滑力以及安全系数的计算公式,从而建立起评判中夹岩安全性的安全系数法,并结合数值模拟对其进行验证。将经验证后的安全系数法应用于某实际隧道工程,判断其中夹岩安全性,得出该隧道中夹岩破坏临界厚度为6 m,进而对6 m以下的中夹岩使用锚杆进行加固。     

A Study on the Modeling and Its Validation for Pedestrian's Knee Ligaments

基于人体模型THUMS中的膝韧带模型,改进了材料参数和单元属性.采用近年较新的生物力学实验数据,逐个验证韧带模型在不同应变率下的生物逼真度.结果表明,膝韧带ACL、PCL、MCL和LCL在不同应变率下的拉力与位移关系曲线与试验结果吻合较好,说明模型具有较好的生物逼真度,能较准确地模拟韧带的损伤和拉伸响应.     

Numerical investigation of a DI diesel spray flame using a detailed chemical reaction mechanism

Emission standards have grown increasingly stricter, consequently triggering greater interest in issues surrounding environmental pollution. In particular, soot and NOx released from DI diesel vehicles is considered to be the main source of air pollution in urban environments. However, the mechanics of fuel spray formation and the influence of the operating parameters on the resulting spray flame are not yet fully understood. In this study, the original KIVA code was modified to incorporate a detailed chemical reaction mechanism involving various species and multiple reaction steps to better understand the spray characteristics. n-Heptane, C₇H₁₆, was used as the representative fuel for diesel fuel, and the reaction mechanism for this fuel was composed of 66 species and 274 elementary reaction steps. The accuracy of the predicted results was demonstrated primarily by a comparison with experimental results. The numerical prediction of a specific operating condition for the parametric investigation correlates well with the experimental results.     

A comparative study on the power characteristics and control strategies for plug-in hybrid electric vehicles

A comparative study was performed on two types of plug-in hybrid electric vehicles (PHEVs): the GM Volt and the Toyota Prius Plug-in Hybrid. First, the powertrain models of the two vehicles were derived. Based on the dynamic models, a detailed component control algorithm was developed for each PHEV. Specifically, a control algorithm was proposed for motor generator 1 (MG1) and MG2 to achieve optimal engine operation. Additionally, an energy management strategy for selecting the operation mode was developed from the viewpoint of fuel economy, battery state of charge and vehicle velocity. Using the dynamic model of the control algorithm for each PHEV, simulations were performed, and the simulation results were verified by comparing them with those obtained using the Powertrain System Analysis Toolkit simulator for the plug-in Prius. Based on the simulation results, a comparative study was performed, and it was found that the role and capacity of MG1 and MG2 and the mode selection algorithm must be determined depending on the configuration of the PHEV.     

Influence of the accelerating operation mechanism on the combustion noise in DI-diesel engines

This paper focuses on the mechanisms of combustion noise during the accelerating operation of multi-cylinder diesel engines using testing technology for the transient conditions of IC engines. Based on impact factors, such as the gas dynamic load and cylinder pressure oscillations, tests and analysis of the combustion noise during transient and steady-state conditions for different loads are made on four-cylinder naturally aspirated engines, turbocharged engines, EGR-introduced engines, and high pressure common rail engines. The laws of combustion noise difference for the same engine speed and load are researched during transient and steady-state conditions. It is found that during transient conditions, the maximum pressure rise rate and the high frequency oscillation amplitude of the cylinder pressure are all higher than those observed during steadystate conditions for the same engine speed and load. With their joint action, the combustion noise during transient conditions is greater than that during steady-state conditions. Turbocharging is useful in reducing the combustion noise during transient conditions. Turbocharging has a better effect on the control over the combustion noise during transient conditions with a constant engine speed and an increasing torque than in conditions with a constant torque and an increasing engine speed. One of the main reasons for different control effects on the combustion noise is that turbocharging causes different wall temperatures inside combustion chambers. The introduction of the appropriate EGR is helpful in the reduction of the combustion noise during transient conditions. The key to the control of combustion noise with EGR during transient conditions is whether a real-time adjustment to the EGR rate can be made to achieve the optimization of the EGR rates for different transient conditions. By means of analyzing the differences in the combustion noise between the transient and steady-state conditions for different pilot injection controls, we obtain a strategy for controlling the combustion noise during transient conditions with a pilot injection. Compared with the steady-state conditions, a larger pilot injection quantity and a longer interval between the main injection and pilot injection should be selected for transient conditions, and this is verified through tests.     

Sensitivity analysis for reducing critical responses at the axle shaft of a lightweight vehicle

Critical responses are frequently detected at the coupled torsional beam axle (CTBA) of a lightweight vehicle. However, the freedom to modify the design of the axle shaft is limited because the suspension system must satisfy other vehicle requirements such as steering performance. Conventional sensitivity analysis cannot provide practical information about the resonant behavior because the analysis only identifies the contribution of the axle shaft to the behavior. This paper presents a novel sensitivity analysis based on transmissibility ratios (TRs). The vehicle components other than the axle shaft that can be modified to control the critical spectra are identified using acceleration responses. A multi-body vehicle model is constructed to simulate the proposed design modifications, and the simulation results show that the vibration of the axle shaft is considerably reduced by the modifications. Because the TRs on the CTBA are effectively minimized through the modified design strategy, the resonant response from the axle shaft can be controlled efficiently.     

Experimental study on the characteristics of nano-particle emissions from a heavy-duty diesel engine using a urea-SCR system

Particulate matter in diesel engine exhaust, particularly nano-particles, can cause serious human health problems including diseases such as lung cancer. Because diesel nano-particle issues are of global concern, regulations on particulate matter emissions specify that not only the weight of particulate matter emitted but also the concentration of nanoparticles must be controlled. This study aimed to determine the effects on nano-particle and PM emissions from a diesel engine when applying a urea-SCR system for NO_x reduction. We found that PM weight increases by approximately 90% when urea is injected in ND-13 mode over the emission without urea injection. Additionally, PM weight increases as the NH₃/NO_x mole ratio is increased at 250 °C. In SEM scans of the collected PM, spherical particles were observed during urea injection, with sizes of approximately 200 nm to 1 μm. This study was designed to determine the conditions under which nano-particles and PM are formed in a urea-SCR system and to relate these conditions to particle size and shape via a quantitative analysis in ND-13 mode.