Contrastive Analysis of Working Face Stability in Cases of Climbing Excavation and Horizontal Excavation北大核心CSCD

Restricted by site and construction period of ancillary structure of metro project, climbing excavation is often adopted. In order to determine tunnel face’s stability, the stabilities of working face in the cases of climbing ex- cavation and horizontal excavation were analyzed by theoretical analysis and numerical simulation. With upperbound limit analysis, the affected scope and positions of failure zone were compared; the position of equivalent strain zone and the law of horizontal displacement changes were studied by simulation analysis. The results show that the scope of failure zone caused by climbing excavation was slightly larger than that by horizontal excavation and the po- sition of affected zone is slightly lower than that by horizontal excavation; the horizontal displacement caused by climbing excavation within a scope of 0-1/3 height of tunnel face is slightly larger than that by horizontal excavation while it is slightly smaller beyond the scope of 0-1/3 height of tunnel face; the maximum horizontal displacements in the cases of climbing and horizontal excavation both occur at the place where is 1/3 height of work face and the de- formation of work face in the case of climbing excavation is not larger than that of horizontal excavation; the work face stabilities are mostly the same in the cases of climbing and horizontal excavation without regard to advanced support, and the work face stability is to be guaranteed with proper advanced support. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Personal security as a transport issue: a state‐of‐the‐art review

The possibility of experiencing attack, assault, violence, robbery, harassment or other anti‐social behaviour has become an important influence on traveller decision‐making. Fear and apprehension about personal security can affect all aspects of travel choice (e.g. choice of route, mode, time of journey, etc.), including whether to travel at all. Indeed, in some locations an informal curfew is reported to operate. However, both the degree and widespread extent of such fears indicate that unacceptable constraints on personal liberty do exist in many locations.

This paper firstly reviews the extent and nature of the problem considering recorded crime statistics, reported levels of fear and apprehension when using transport facilities and subsequent modifications to travel behaviour. Secondly, a range of possible responses by transport operators, policing agencies and national and local government are examined under four broad headings: policing and staffing; situational crime prevention; social crime prevention; and the level and quality of transport service provision.

It is concluded that personal security considerations need to be explicitly incorporated into decisions concerning the design, planning, operation and management of transport systems. It is also important that institutional structures exist to permit the issue both to be recognized and tackled.     

Multiple criteria evaluation of transportation system improvement projects: The case of korea

As a newly industrialized country, Korea has shown remarkable economic progress in the last three decades. This phenomenal growth has rapidly increased demands for better quality of life. This includes, among others, increasing demand for high quality transportation system services. In this paper, the method of Analytic Hierarchy Process (AHP) is utilized to evaluate rural highway improvement projects in Korea. The appropriate rural highway improvement projects for widening and paving were selected and studied on the basis of some selection criteria. The results have shown that there are some significant differences in prioritizing projects using the traditional economic evaluation method as compared to those resulting from the use of AHP. As demonstrated, the AHP proves to be an effective tool in evaluating transportation system projects.     

Transportation planning and institutional rigidities in Surat,India

This paper while reviewing the prevalent traffic and transportation problems in a metropolitan city of India namely Surat, identifies certain institutional rigidities which mar prospects of planned improvements. The old city of Surat known as the Walled City is the center of chronic traffic congestion which is due to a variety of causes. Owing to the past neglect and the on-going developments, the Walled City is beset with numerous traffic and transportation as well as other problems. Based on an indepth analyses of field data, a series of short and long term remedial measures were worked out to cope with the immediate and the future travel demands. Of the proposals made, the traffic management scheme is designed to optimize the use of available infrastructural facilities with a thrust towards bus transportation. However, the success of these measures depends on the relaxation of the outdated practices which could stifle the implementation of the suggested solutions.     

Characteristics of truck traffic in Singapore

This paper presents the results of a project conducted to study the characteristics of truck traffic in Singapore. Detailed traffic surveys recording counts of vehicles by axle-configuration were performed at 219 sites over a period of nearly two years. The surveys covered 5 different road classes, namely expressways, arterials, collectors, industrial roads and local roads. It was found that the time distribution of truck travel were not the same among the five road classes. The peaking characteristics of truck traffic were less pronounced compared to passenger car traffic. The peak hour truck volume varied from 67.0% to 9.7% of the daily truck traffic as compared to 13.8% for passenger car traffic. The lane distribution pattern of truck traffic was studied in detail by road class, and was found to be a function of total directional traffic volume, total directional truck volume and the number of traffic lanes. Composition analysis was also carried out to study the lane use characteristics of single- and multiple-unit trucks.     

Optimal design of the exhaust system layout to suppress the discharge noise from an idling engine

At the idle engine speed, the exhaust discharge noise is influenced by resonances in the whole system, which is composed of connecting pipes and silencers. This pipe resonance radiates a high level of low frequency discharge noise, which is dominated by the low order harmonics of the engine firing frequency. This low frequency noise deteriorates the vehicle’s interior noise level and quality. The following study attempted to optimize the layout of an exhaust system to minimize low frequency noise by changing the position of silencers and the lengths of inlet and outlet pipes in each silencer. After modeling the exhaust system using four-pole parameters, the acoustical performance of the system was evaluated using the system insertion loss. In the optimization, the virtual attenuation coefficient, which corresponds to the amount of attenuation coefficient required for the silencers, was calculated to find a minimum value for the layout. The simulated annealing method, which is also known as finding an optimal, was employed in searching for the optimized exhaust layout. Test examples of two cases, for two and six design variables, were used. When the number of design variables was two, the positions of the center and rear silencers were considered. When the number of design variables was six, the positions of the two silencers and the lengths of the inlet and outlet pipes were considered. Three typical layouts for the exhaust system of each case were designed, including the given system and an optimal system. By comparing the predicted and measured discharge noise level, it was confirmed that the optimized exhaust layout has a higher noise reduction than the other layout designs.     

Automotive windshield — pedestrian head impact: Energy absorption capability of interlayer material

During accident, the interlayer of windshield plays an important role in the crash safety of automotive and protection of pedestrian or passenger. The understanding of its energy absorption capability is of fundamental importance. Conventional interlayer material of automotive windshield is made by Polyvinyl butyral (PVB). Recently, a new candidate of high-performance nanoporous energy absorption system (NEAS) has been suggested as a candidate for crashworthiness. For the model problem of pedestrian head impact with windshield, we compare the energy absorption capabilities of PVB and NEAS interlayers, in terms of the contact force, acceleration, velocity, head injury criteria, and energy absorption ratio, among which results obtained from PVB interlayers are validated by literature references. The impact speed is obtained from virtual test field in PC-CRASH, and the impact simulations are carried out using explicit finite element simulations. Both the accident speed and interlayer thickness are varied to explore their effects. The explicit relationships established among the energy absorption capabilities, impact speed, and interlayer material/thickness, are useful for safety evaluation as well as automotive design. It is shown that the NEAS interlayer may absorb more energy than PVB interlayer and it may be a competitive candidate for windshield interlayer.     

Current sensorless drive method for electric power steering

This paper proposes a current sensorless drive method by using the mathematical modeling of a surface-mounted permanent magnet synchronous motor (SPMSM) and a dead-time compensation method to reduce the calculated current error caused by differences between real output voltages and voltage commands. The proposed method is implemented by using only a processor algorithm internally, i.e., without any voltage-sensing circuit hardware, such as filtering circuits and current sensor feedback circuits. To show the effectiveness of the proposed method, MATLAB simulations are carried out with an Electric Power Steering (EPS) System containing an SPMSM, a motor drive system and a mechanical gear system. The result shows the validity of the proposed method.     

Modeling and model predictive control for hybrid electric vehicles

This paper builds up a typical model of a parallel hybrid electric vehicle and develops model predictive controllers for this model to control the speeds and torques for fast clutch engagement with high driving comfort and low jerk. Some modified algorithms for model predictive controllers are studied to improve their ability to track the desired speed setpoints, subject to input and output constraints.     

Starting sliding mode variable structure that coordinates the control and real-time optimization of dry dual clutch transmissions

This paper researches the coordination of control between an engine and clutch at the system level to adequately reflect a driver’s intention and improve the starting performance of a vehicle equipped with a dry dual clutch transmission (DCT). Four-degree-of-freedom (DOF) starting dynamic equations are established for a dry DCT with a single intermediate shaft, and a two-DOF model of the sliding friction process and a single-DOF in-gear model of stable operation are obtained after simplifying these equations. Taking advantage of predictive control and a genetic algorithm, target tracing curves of the engine’s speed and the vehicle’s velocity are optimally specified online, and the starting sliding mode variable structure (SMVS) coordinating control strategy is designed to track these curves. The starting performance of a prototype car equipped with a dry DCT is simulated under different starting cases on the MATLAB/Simulink software platform. The simulation results show that the designed SMVS coordinating controller not only embodies driver intention and effectively improves the dry DCT car’s starting performance but is also highly robust when subjected to variations in the vehicle parameters.