Application of Aerodynamic Actuators to Improve Vehicle Handling

This exploratory study considers applications of active aerodynamic devices for suppressing parasitic motion and for improving the response of vehicles to steering, within the scope of the linear dynamic behaviour. A three DOF linear model is chosen to describe the side slip, yaw and roll motion of a baseline front-wheel steered vehicle. The improvements in performance of the base-line vehicle that are achievable by the application of direct yaw and roll moments are determined when either an open loop control pre-filter or a state feedback control law based on LQR design is applied. Unlike the former control, the state feedback control is unable to make the body side-slip angle vanish. The feedback control performance of each of the two moment actuators has been examined separately and then jointly. The advantages of combining the open loop and feedback dual actuator configurations are demonstrated using the two-degree of freedom control scheme. It is found that the scheme yields a spectacular performance but demands unreasonably large moments from the actuators in the context of available aerodynamic forces. On the other hand, the demand on direct yaw and roll moment of actuators is modest when the actuators are controlled using the LQR feedback only and if the control design is used to track a desired yaw rate trajectory and simultaneously to reduce the parasitic rolling motion. Significant improvements in handling and dynamic stability of a base-line vehicle can be achieved by aerodynamically generated direct yaw and roll actuator moments provided the target control performance is reasonable. The configurations of aerodynamic actuators considered are feasible for improving vehicle handling in cornering on motorways but more work remains to be done to explore alternative aerodynamic configurations that give rise to less side effects and higher lift coefficients.     

Optimizing the transportation of international container cargoes in Korea

This paper considers a multimodal transportation problem, which is the problem of determining the transportation flow, i.e. volume of container cargoes, and the transportation mode in each trade route, for the objective of minimizing the sum of shipping and inland transportation costs. The problem takes account of two restrictions: maximum cargo volumes capacitated at each seaport and maximum number of vehicles available at each transportation mode. To solve optimally the problem, this paper employs a mixed integer programming, which is an operations research technique. A case study is performed on the container cargo data in Korea and we draw several implications to improve efficiency in the transportation of international trade cargoes in Korea.     

Measurement of air–water CO2 transfer at four coastal sites using a chamber method

We measured the air–water CO₂ flux in four coastal regions (two coral reefs, one estuary, and one coastal brackish lake) using a chamber method, which has the highest spatial resolution of the methods available for measuring coastal air–water gas flux. Some of the measurements were considerably higher than expected from reported wind-dependent relationships. The average k₆₀₀ values for Shiraho Reef, Fukido Reef, Fukido River, and Lake Nakaumi were 1.5 ± 0.6, 3.2 ± 0.3, 0.69 ± 0.26, and 2.2 ± 0.9 (mean ± S.D.) times larger than the wind-dependent relationships. Results were compared with current-dependent relationships and vertical turbulence intensity (VTI). VTI is an index of water-surface stirring and is calculated from near-surface vertical velocity. Although some measurements from the reefs and river closely matched those expected from wind-dependent relationships, others were considerably higher. All data were correlated with VTI and were qualitatively explained by bottom macro-roughness enhancement. In Lake Nakaumi, results tended to differ from the wind-dependent relationships, and the difference between the measured and expected gas-transfer velocity was correlated with biological DO changes and/or the intensity of density stratification. We found these factors to have important effects on coastal gas flux. In addition, the chamber method was an effective tool for evaluating coastal gas flux.     

The combined effect of rain and wind on air–water gas exchange: A feasibility study

A series of experiments were conducted at University of Delaware's Air–Sea Interaction Laboratory to examine the combined effects of rain and wind on air–water gas exchange. During this study, ASIL WRX I, a combination of 3 rain rates and 4 wind speeds were used, for a total of 12 different environmental conditions. The SF₆ evasion method was used to determine the bulk gas transfer velocities, and airside profiles of wind and CO₂ were used to estimate flux–profiles of momentum and carbon dioxide. In addition to measurements of fluxes with and without rain in a wind–wave boundary layer, measurements of wave properties were also obtained. Rain is shown to alter the wind profile in the flume, and dampen surface waves. Also, SF₆ evasion indicates that with the present experimental setup, for most of the experimental conditions, rain and wind combine linearly to influence air–water gas exchange. Flux–profile relationships for marine atmospheric boundary layers, which were performed to scale up to field measurements, were explored by a comparison between SF₆-derived bulk fluxes and airside CO₂ profile measurements.     

Seasonal study of dissolved CH4, CO2 and N2O in a shallow tidal system of the bay of Cádiz (SW Spain)

During 2004, 10 samplings were performed in order to measure dissolved methane (CH₄), carbon dioxide (CO₂) and nitrous oxide (N₂O) in the surface waters of Río San Pedro, a tidal creek in the salt marsh area of the Bay of Cádiz (SW Spain). The inner partvs of the creek is affected by the inputs coming from an intensive fish farm and the drainage of an extensive salt marsh area.Dissolved CH₄, CO₂ and N₂O concentrations ranged from 11 to 88 nM, 36 to 108 μM and 14 to 50 nM, respectively. Surface waters were in all cases oversaturated with respect to the atmosphere, reaching values of up to 5000% for CH₄, 1240% for CO₂ and 840% for N₂O. Dissolved CH₄, CO₂ and N₂O showed a significant tidal and seasonal variability. Over a tidal cycle, concentrations were always highest during low tide, which points to the influence of the inputs from the fish farm effluent and the drainage of the adjacent salt marsh area, as well as in situ production within the system. Dissolved CH₄, CO₂ and N₂O seasonal patterns were similar and showed maximum concentrations in summer conditions. Using four different parameterizations to calculate the gas transfer coefficients [Liss, P.S. and Merlivat, L., 1986. Air-sea exchange rates: introduction and synthesis. In P. Buat-Ménard (Ed.), The Role of Air-Sea Exchanges in Geochemical Cycling. Reidel, Dordrecht, The Netherlands, p. 113–127.; Clark, J.F., Schlosser, P., Simpson, H.J., Stute, M., Wanninkhof, R., and Ho, D.T., 1995. Relationship between gas transfer velocities and wind speeds in the tidal Hudson River determined by the dual tracer technique. In: B. Jähne and E. Monahan (Eds.), Air-Water Gas Transfer: AEON Verlag and Studio, Hanau, Germany, pp. 785–800.; Carini, S., Weston, N., Hopkinson, G., Tucker, J., Giblin, A. and Vallino, J., 1996. Gas exchanges rates in the Parker River estuary, Massachusetts. Biol. Bull., 191: 333–334.; Kremer, J.N., Reischauer, A. and D'Avanzo, C., 2003. Estuary-specific variation in the air-water gas exchange coefficient for oxygen. Estuaries, 26: 829–836.], the averaged air–water fluxes of CH₄, CO₂ and N₂O from the creek to the atmosphere ranged between 34 and 150 μmol CH₄ m^− 2 day^− 1, 73 and 177 mmol CO₂ m^− 2 day^− 1 and 24 and 62 μmol N₂O m⁻² day⁻¹, respectively.     

A computational approach for fatigue crack propagation in ship structures under random sequence of clustered loading

The authors have developed a simulation program, CP-System, for multiple cracks propagating in a three-dimensional stiffened panel structure, where through-the-thickness crack propagation is formulated as a two-dimensional in-plane problem, and the crack propagation behavior is simulated by step-by-step finite element analyses. In order to evaluate the fatigue lives of marine structures accurately, it is necessary to take into account the load histories induced by sea waves, which may be composed of a random sequence of certain clustered loads with variable stress range. In the proposed crack growth model, the crack opening and closure behavior is simulated by using the modified strip yielding model, and the effective tensile plastic stress intensity range, ΔK _RP, is calculated by considering the contact of plastic wake along the crack surfaces. The adequacy of the proposed crack growth model is examined by comparison with fatigue tests under non-constant-amplitude loading. The usefulness of the developed method is demonstrated for a ship structural detail under certain simulated load sequences. It is shown that the fatigue crack growth of a ship structure is significantly retarded due to the load interaction effects, so that the conventional method for fatigue life assessment may predict a relatively conservative fatigue life of a structure.     

船舶辅机浮筏半主动非线性隔振系统振动特性分析

磁流变阻尼器因其低耗能、响应迅速等特点而被广泛应用。文章采用一种改进的Bingham模型对船舶辅机浮筏隔振装置中的非线性磁流变阻尼力进行建模。该模型简单且含滞后特性,便于理论分析。对建立的船舶辅机浮筏隔振系统的非线性动力学模型,通过平均法求解船舶辅机浮筏半主动隔振系统的理论解,并运用Matlab对理论解进行数值仿真验证。以力传递率作为评价指标,分析了磁流变阻尼器各参数对隔振效果的影响规律。研究结果可为非线性船舶辅机浮筏隔振系统的设计提供理论依据,从而能更有效地控制船舶辅机的振动。     

Electromagnetic valve train for gasoline engine exhaust system

Electromagnetic valve train (EMVT) in camless engine offers large potential for both part load fuel economy and high load engine torque. However, it is more difficult to be applied on exhaust system than intake system. Because the gas pressure brings high demands for driving force, especially at high engine speed and full load. Based on the working characters of actuator, a method by increasing the transient currents in windings during valve’s opening motion is suggested to overcome the gas pressure. But this will cause more energy losses and heat. In order to make the EMVT used on exhaust system better, quantitative analysis is carried out against the additional power consumption caused by gas pressure under different conditions. Furthermore, an approach is introduced to define the optimal exhaust valve opening motion at full load conditions. It aims at making a better compromise between the engine power output and exhaust valves’ power consumption, thus both the efficiency of EMVT and engine performance are enhanced.     

Hot judder simulation of a ventilated disc and design of an improved disc using sensitivity analysis

In a disc brake system, thermal expansion of the material is caused by friction energy that is generated by the sliding contact between a disc and pad during braking. This phenomenon, thermo-elastic instability, can lead to hot spots on the disc surface and a hot judder phenomenon. Transient finite element analysis has been used to simulate this phenomenon. Three dimensional finite element models of a disc, pad, and cylinder were created. Each part was connected by a joint. Contact condition was applied to the disc and pad with a friction coefficient (μ) of 0.4. A convective heat transfer coefficient was set as 40 W/m²K. Using a commercial program SAMCEF, the simulation of the thermo-mechanically coupled system was performed. In order to find the sensitive parameters of brake judder, sensitivity analysis was carried out with consideration for disc design parameters. As a result, the hot spot phenomenon was confirmed and hot judder was predicted. Moreover, the more sensitive parameters of the hot judder phenomenon were presented. Finally, an improved disc model and an analysis technique were verified by comparison to dynamo test results.     

Prediction procedure for wear distribution of transient rolling tire

As a research method, finite element analysis (FEA) with ABAQUS can help researchers to study throughout the whole process of abnormal tire wear. For precise tread wear simulation, this paper introduces a tire finite element model building method. Then, the model is verified by comparing its simulation results with experiment data. Based on the verified model, tire high-speed rolling procedure is presented by combining steady-state transport analysis and dynamic analysis. To predict the wear distribution, micro tread wear calculation method is described. Finally, the wear prediction procedure of tread mesh evolving is introduced and tire polygonal wear pattern is simulated by this procedure.