Fuel consumption parameters for realizing and verifying fuel consumption prospect algorithm of vehicle driving route information system

Emissions of CO₂, as the main component of greenhouse gases, and high fuel consumption rates are worldwide problems. To solve them, most car manufacturers have concentrated on developing various techniques to improve the efficiencies of engines and transmissions and ECO-ROUTEs to meet environmental regulations. In this study, an algorithm for determining routes that cause the least fuel consumption was developed. The core of this algorithm is a specific EEC (energy efficiency constant) map containing logic that is able to predict fuel consumption. The accuracy of the algorithm was confirmed by vehicle tests for various driving patterns. Parameters affecting vehicle fuel economy were studied and verified. Improvement in the accuracy of this algorithm was confirmed by applying these parameters to ECO-ROUTE logic.     

Hot judder simulation of a ventilated disc and design of an improved disc using sensitivity analysis

In a disc brake system, thermal expansion of the material is caused by friction energy that is generated by the sliding contact between a disc and pad during braking. This phenomenon, thermo-elastic instability, can lead to hot spots on the disc surface and a hot judder phenomenon. Transient finite element analysis has been used to simulate this phenomenon. Three dimensional finite element models of a disc, pad, and cylinder were created. Each part was connected by a joint. Contact condition was applied to the disc and pad with a friction coefficient (μ) of 0.4. A convective heat transfer coefficient was set as 40 W/m²K. Using a commercial program SAMCEF, the simulation of the thermo-mechanically coupled system was performed. In order to find the sensitive parameters of brake judder, sensitivity analysis was carried out with consideration for disc design parameters. As a result, the hot spot phenomenon was confirmed and hot judder was predicted. Moreover, the more sensitive parameters of the hot judder phenomenon were presented. Finally, an improved disc model and an analysis technique were verified by comparison to dynamo test results.     

Prediction procedure for wear distribution of transient rolling tire

As a research method, finite element analysis (FEA) with ABAQUS can help researchers to study throughout the whole process of abnormal tire wear. For precise tread wear simulation, this paper introduces a tire finite element model building method. Then, the model is verified by comparing its simulation results with experiment data. Based on the verified model, tire high-speed rolling procedure is presented by combining steady-state transport analysis and dynamic analysis. To predict the wear distribution, micro tread wear calculation method is described. Finally, the wear prediction procedure of tread mesh evolving is introduced and tire polygonal wear pattern is simulated by this procedure.     

Model for dynamic behavior of the crankshaft of an air cooled diesel engine subjected to severe functioning

The dynamic behavior of the engine organs in severe conditions is complicated to identify. In this paper, the dynamic behavior of the crankshaft of the diesel engine Deutz F8L413 direct injection-type air cooled in the severe operating conditions is investigated in a 3D global model. The maximum operating characteristics of the engine are experimentally measured on a bench test equipped with a hydraulic brake. The most stressed areas of the crankshaft are determined by numerical simulations. In addition, an analysis of the fatigue behavior of the crankshaft is carried out by using two fatigues criteria. The efficiency of the model is demonstrated by comparing between the numerical results and the experimental data obtained with the natural modes of vibration test.     

Influence of pilot injection on combustion characteristics and emissions in a DI diesel engine fueled with diesel and DME

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion and emissions characteristics (NOx, CO, THC and smoke) in a single-cylinder DI diesel engine. The experiments were conducted using two fuel injection systems according to the fuel type, diesel or dimethyl ether (DME), due to the different fuel characteristics. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (?4°CA aTDC, ?2°CA aTDC, 0°CA aTDC, 2°CA aTDC and 4°CA aTDC). Results from pilot-main injection conditions are compared with those shown in single injection conditions to better demonstrate the potential of pilot injection. It was found that pilot injection is highly effective for lowering heat-release rates with smooth pressure traces regardless of the fuel type. Pilot injection also offers high potential to maintain or increase the BMEP; even the combustion-timing is retarded to suppress the NOx emission formation. Overall, NOx emission formation was suppressed more by the combustion phasing retard effect, and not the pilot injection effect considered in this study. Comparison of the emissions for different fuel types shows that CO and HC emissions have low values below 100 ppm for DME operation in both single injection and pilot-main injection. However, NOx emission is slightly higher in the earlier main injection timings (?4°CA aTDC, ?2°CA aTDC) than diesel injections. Pilot injection was found to be more effective with DME for reducing the amount of NOx emission with combustion retardation, which indicates a level of NOx emission similar to that of diesel. Although the diesel pilot-main injection conditions show higher smoke emission than single-injection condition, DME has little smoke emission regardless of injection strategy.     

「台湾桃园国际机场联外捷运系统建设计划」地下工程的设计与施工

介绍「台湾桃园国际机场联外捷运系统建设计划」中机场区段地下工程的设计成果,并探讨施工时将面临的主要工程问题如,潜盾隧道穿越营运中的机场滑行道下方需考虑对其进行保护、隧道遭遇既有地锚的处理方式,及明挖覆盖隧道或车站于卵砾石层进行开挖,临时挡土措施及潜盾隧道的掘进作业,需考虑卵砾石大粒径与高硬度的特性等等设计考虑.现有数据显示,透过适当的机具改良、辅助工法的应用及良好的施工管理,即使是在高地下水压的卵砾石层,施作地下连续壁及以潜盾机施作隧道并无太大困难,且施工引致的地表沉陷及施工精度亦可获得良好的控制.     

Combined effect of boost pressure and injection timing on the performance and combustion of CNG in a DI spark ignition engine

There is an increasing interest in supercharging spark ignition engines operating on CNG (compressed natural gas) mainly due to its superior knock resisting properties. However, there is a penalty in volumetric efficiency when directly injecting the gaseous fuel at early and partial injection timings. The present work reports the combined effects of a small boost pressure and injection timing on performance and combustion of CNG fueled DI (direct injection) engine. The experimental tests were carried out on a 4-stroke DI spark ignition engine with a compression ratio of 14. Early injection timing, when inlet valves are still open (at 300°BTDC), and partial injection timing, in which part of the injection occurs after the inlet valves are closed (at 180°BTDC), were varied at each operating speed with variation of the boost pressure from 2.5 to 10 kPa. A narrow angle injector (NAI) was used to increase the mixing rate at engine speeds between 2000 and 5000 rpm. Similar experiments were conducted on a naturally aspirated engine and the results were then compared with that of the boosting system to examine the combined effects of boost pressure and injection timing. It was observed that boost pressure above 7.5 kPa resulted in an improvement of performance and combustion of CNG DI engine at all operating speeds. This was manifested in the faster heat release rates and mass fraction burned that in turn improved combustion efficiency of the boosting system. An increased in cylinder pressure and temperature was also observed with boost pressure compared to naturally aspirated engine. Moreover, the combustion duration was reduced due to concentration of the heat release near to the top dead center as the result of the boost pressure. Supercharging was also found to reduce the penalty of volumetric efficiency at both the simulated port and partial injection timings.     

Majorization of working parameters for non-thermal plasma reactor and impact on no oxidation of diesel engine

The main target of this work is to realize the function of pre-oxidizing NO from diesel engine’s exhaust by using self-designed double-dielectric Non-thermal Plasma (NTP) reactor. The majorized discharge frequency and discharge peak to peak voltage (V_p-p) range for NTP reactor were obtained through air discharge test. The diesel engine test bench was established to observe the effect of NTP on the volume fraction of NO. The results showed that there were more active substances and fewer by-products in NTP reactor when discharge frequency was 9 kHz and V_p-p was between 9 kV and 23 kV; Exhaust flows had insignificant effect on the performance of NTP pre-oxidizing NO; The ability of NTP to pre-oxidize NO gradually weakened with the increase of engine load, and when the engine load were 0 % and 25 %, the ratio of NO/NO₂ could reach 1. In such working conditions, SCR system could improve the conversion rate of the NO_x at low-temperature zone through quick reaction combined with NTP.     

Electromagnetic valve train for gasoline engine exhaust system

Electromagnetic valve train (EMVT) in camless engine offers large potential for both part load fuel economy and high load engine torque. However, it is more difficult to be applied on exhaust system than intake system. Because the gas pressure brings high demands for driving force, especially at high engine speed and full load. Based on the working characters of actuator, a method by increasing the transient currents in windings during valve’s opening motion is suggested to overcome the gas pressure. But this will cause more energy losses and heat. In order to make the EMVT used on exhaust system better, quantitative analysis is carried out against the additional power consumption caused by gas pressure under different conditions. Furthermore, an approach is introduced to define the optimal exhaust valve opening motion at full load conditions. It aims at making a better compromise between the engine power output and exhaust valves’ power consumption, thus both the efficiency of EMVT and engine performance are enhanced.     

Proposed quick method for applying dynamic lane assignment at signalized intersections

Almost all researches about dynamic lane assignment were conducted to evaluate the effectiveness of applying this technique at signalized intersections. However, little attention was given to the method of identifying quickly the optimum lane group. This research suggests a quick method to find the optimum lane group for 3-lane and 4-lane approaches at junctions where each approach has green by itself in turn using the percentage of turning movements. MATLAB environment was used to build an optimization model to find the optimal lane groups at all intersection approaches for hypothetical massive traffic demand combinations using an objective function of minimizing intersection delay. This finding represents a plausible quick method to predict the optimum lane group in the field instantaneously using the percentage of turning movements at the approach without conducting massive calculations.