Regional impacts of new transport infrastructure: a multisectoral potentials approach

This is the second of two background papers sponsored for the Symposium by the Administrative Commission for the north of the Netherlands. Its purpose is to provide an indication of the effects of the proposed high speed rail line between Amsterdam, Groningen and Hamburg on employment in the corridor. The authors first review the techniques of forecasting these effects discussed in the literature. The potentials approach is adopted for their analysis, the mathematics and underlying assumptions of which are presented. Finally, this model is run to provide an estimate of the impact on regional employment of three variants of the proposed rail line.     

养生作用对硫沥青性能影响分析

硫磺部分替代传统石油沥青用于道路工程建设可减少石油沥青用量,降低施工能源消耗,促进工业废渣中硫磺的回收利用,具有较高的经济和环保价值。为探究硫磺掺量（质量分数）及养生作用对硫沥青（SEA）性能的影响,采用差示扫描量热仪（DSC）验证硫沥青中硫磺的重结晶现象,对养生前后硫沥青的基本物理性能和黏度进行分析,并采用动态剪切流变仪（DSR）和弯曲梁流变仪（BBR）对养生前后硫沥青的流变特性和疲劳性能进行评价,最后借助荧光显微镜（FM）观察养生前、后硫磺在沥青中的微观分布特性。研究结果表明：养生后高硫磺掺量的硫沥青DSC曲线出现吸热峰,硫沥青（特别是高硫磺掺量下）的劲度有所增加,因此对硫沥青进行养生使其性能稳定后再进行相关性能评价更具现实意义;硫磺掺量较低（≤ 10%）时,硫磺主要以溶解硫的形式存在于沥青中起到软化沥青的作用,因此沥青的低温变形能力有所改善,但其高温抗变形能力有所降低;当硫磺掺量较高（≥ 35%）时,硫磺主要以重结晶的形式悬浮在沥青中使沥青变硬,在增加沥青高温抗变形能力的同时也牺牲了其低温抗裂能力;硫磺掺量较低时,硫沥青黏度随着硫磺掺量的增加而降低;硫磺掺量较高时,硫沥青90℃和105℃黏度随着硫磺掺量的增加而增加,但硫沥青120℃和135℃黏度相差不大,同时硫磺加入最高可降低沥青的施工温度达20℃;线性振幅扫描（LAS）试验结果表明,养生后的硫沥青疲劳寿命比基质沥青长,其中35%硫沥青疲劳性能最佳;硫磺掺量进一步增加,硫沥青疲劳寿命缩短至与基质沥青相近;FM分析表明,硫磺掺量不高于5%时,硫磺全部溶解于沥青中,且养生后硫磺未重结晶,相应硫沥青无荧光性;硫磺掺量高于5%时,硫磺在沥青中分布均匀,养生后10%硫沥青中硫晶斑尺寸和面积显著增大,高硫磺掺量硫沥青中硫晶斑面积仅略有增加。     

Micro-Grinding Performance of Hard-Brittle Chip Materials in Precision Micro-Grinding Microgroove

The micro-structure on hard-brittle chip materials (HBCMs) surface can produce predominant functions and features. The micro-grinding with diamond wheel micro-tip is an efficient method to machine microstructure on HBCMs. However, different HBCMs and crystal orientation may have a significant influence on the micro-grinding performance. In this paper, the micro-grinding performance along different crystal orientation of HBCMs is investigated. First, a dressed 600^# diamond grinding wheel is used to micro-grind micro-structure on HBCMs. Then, the experiment of micro-grinding force test is completed. Finally, the quality of microgroove, the grinding ratio and the micro-grinding force are investigated and they are related to the crystal orientation of HBCMs. It is shown that the stronger resistance to the micro-crack propagation has the best quality of microgroove and the smallest grinding ratio. Moreover, the hardest single-crystal SiC has the best machinability and the micro-grinding force is 38.9%, 10.8% and 46.8% less than the one of sapphire, single-crystal Si and quartz glass, respectively. The direction to micro-grind easily is the crystal orientation 〈10\(\overline 1 \)0〉 for single-crystal SiC and sapphire. In addition, the micro-grinding force increases with the increase of the micro-grinding depth and feed rate and decreases with the increase of the grinding wheel speed.     

Lattice-based group signature with verifier-local revocation

Among several post quantum primitives proposed in the past few decades, lattice-based cryptography is considered as the most promising one, due to its underlying rich combinatorial structure, and the worst-case to average-case reductions. The first lattice-based group signature scheme with verifier-local revocation(VLR) is treated as the first quantum-resistant scheme supported member revocation, and was put forward by Langlois et al. This VLR group signature(VLR-GS) has group public key size of O(nm log N log q), and a signature size of O(tm log N log q log β). Nguyen et al. constructed a simple efficient group signature from lattice, with significant advantages in bit-size of both the group public key and the signature. Based on their work, we present a VLR-GS scheme with group public key size of O(nm log q) and signature size of O(tm log q). Our group signature has notable advantages: support of membership revocation, and short in both the public key size and the signature size.     

Research on the Influence of Vertical Deformation of Bridge on the Track RegularityEI北大核心

Research purposes: The vertical deformation of high-speed railway (HSR) bridge will cause the track irregularity, which threatens the safe and efficient operation of the HSR. Taking the 32 m simple supported beam bridge as the research object, based on the existing mapping analytical model for bridge vertical deformation and rail geometry, the influence of the track regularity of the CRTS Ⅰ slab ballastless track structure caused by the key parameters such as the bridge vertical deformation amplitude, the hanging length of the beam end and the vertical stiffness of mortar layer were studied, and the corresponding measures to control the rail deformation were proposed, to provide theoretical reference for comprehensive treatment of rail deformation of HSR bridge. Research conclusions:(1) The pier settlement, the vertical rotation of the beam end and the beam fault will cause the rail to follow the beam deformation, and "up-warping" of the rail on the vertical deformation boundary will appear. (2) The rail deformation is directly proportional to the vertical deformation amplitude of the bridge and the key to control the rail deformation is to reduce the vertical deformation of the bridge. (3) The rail deformation can be controlled by reducing the hanging length of beam and vertical stiffness of mortar layer. (4) The research results can provide a theoretical reference for controlling the vertical rail deformation of high-speed railway bridges. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

The Reinforcement Analysis of Prestressed Anchor Frame Beam in the Deep Cutting Slope under Three Dimensional Strong EarthquakeEI北大核心

Research purposes: In order to further study the reinforcement of prestressed anchor frame beam in the deep cutting slope under three dimensional strong earthquake, a model of the deep cutting slope is built through FLAC 3D simulation software, the seismic wave to the model from three directions of x,y and z is input, and the dynamic response of the slope is analyzed. Then, the prestressed anchor frame beam reinforcement measures are applied to the model, and this paper analyzes the reinforcement effect of the prestressed anchor frame beam to the deep cutting slope under three dimensional strong earthquake. Research conclusions:(1) The prestressed anchor frame beam has a good effect on restraining the horizontal displacement of the deep cutting slope. (2) Under the three dimensional strong earthquake, the prestressed anchor frame beam has a good effect on the horizontal acceleration and horizontal velocity of the deep cutting slope, which reduces the peak of horizontal acceleration and horizontal velocity. (3) Through the comparison of the response before and after the reinforcement of the prestressed anchor frame beam is given under the 9 degrees three dimensional strong earthquake, it can be concluded that the prestressed anchor frame beam can provide good reinforcement effect to the deep cutting slope. (4) This research can be used for reference to the earthquake resistance of the slope engineering. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

功率循环测试中衬底焊接层的可靠性

基板与陶瓷衬底之间的焊层寿命通常利用IGBT模块的被动加热和冷却(热循环)来测试,但这种试验会引起焊层失效(分层)。实际应用中,IGBT和二极管芯片是主动被加热的,诸如焊线脱落等其它模式的失效也会限制使用寿命,通常可通过功率循环试验来评估这种应力的影响。本文通过功率循环试验来评估衬底焊层的失效,利用高循环周次的测试进行有效的衬底焊层热循环试验,其关键在于功率循环过程中焊层温度的预测。在温度波动不大的条件下,比较了被动热循环和主动功率循环时对焊接寿命的影响。     

Regulatory reform and freight mode choice

Reform of trucking Vehicle Weights and Dimensions (VWD) regulations in Canada is now underway. The effect these reforms will have on the freight transportation industry are only recently the subject of research. This paper is part of this new research effort, aimed at understanding how regulatory reform in the trucking sector will affect the existing competitive relationship between trucks and the railways. The paper presents the results of study and research into modelling the relationship between mode choice and the service characteristics that are affected by VWD reform.Using several periods of data, a series of econometric models are developed which help to elucidate the relative relationships between the mode service characteristics for both of the principal interprovincial freight modes. A technique is developed and presented to model railway user costs in order to overcome the complex and often unrepresentable pricing activities of Canadian railways.The strength of the developed econometric models is presented, including their significance and statistical reliability. This is further reinforced by the similarities exhibited by all the models in the series. The selected model is applied to predict market service responses required of the railway industry in order to compete with the trucking sector now adapting to the new regulations.The impact of the newly implemented vehicle weight and dimension reform on the rail transportation industry is analyzed and railway industry improvements aimed at maintaining its market share are presented. The results predicted by the model show that railway user cost reductions should be moderate, and likely less than the level of inflation over the period of time when trucking converts its fleet to take advantage of the new regulations.Abbreviations AASHTO American Association of State Highway and Transportation Officials - CCMTA Canadian Conference of Motor Transport Administrators - EPI End products, inedible commodity classification - GVW Gross Vehicle Weight - NA 1988 VWD National Agreement - RTAC Roads and Transportation Association of Canada - VWD Vehicle Weight(s) and Dimension(s) - WA 1988 VWD Western Agreement     

Modeling intrametropolitan industrial location realistically

This paper compares intrametropolitan industrial location models to the process of intrametropolitan industrial location as described in the real estate and urban economic literature. It identifies seven areas where industrial location models are at odds with reality, and suggests ways to make them realistic. Specifically, it makes a case for microanalytic/stochastic/recursive/dynamic/economic industrial location models. It goes on to describe an operational model that is realistic in most respects.