Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.     

Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

Effect of fuel stratification on initial flame development: Part 3-high swirl condition

This paper discusses the final investigation into the effect of fuel stratification on flame propagation. In previous works, the characteristics under the no port-generated swirl condition and the low-swirl condition were considered. For this purpose, the initial flame development and propagation were visualized under different axially stratified states in a modified optical single-cylinder SI engine. The images were captured by an intensified CCD camera through the quartz window mounted in the piston. Stratification was controlled by the combination of the port swirl ratio and injection timing. These were averaged and processed to characterize the flame propagation. The flame stability was estimated by the weighted average of flame area and luminosity. The stability was also evaluated through the standard deviation of flame area and propagation distance and through the mean absolute deviation of the propagation direction. The results show that the LML is expanded remarkably under the high-swirl cases up to the highest relative AFRs of 1.71 and 1.75 between 140 and 160CA. In addition, similar to the low-swirl condition, the flame-flow interaction determines the direction of flame propagation, and the governing roles of the two factors vary according to the swirl level; the flow is more important at the higher swirl conditions, and the flame is more important at the lower swirl condition. Finally, fast and stable flame propagation can be achieved under the preferably stratified condition, which is induced by the suitable combination of the high swirl and injection timing.     

Simulating the impacts of household travel on greenhouse gas emissions,urban air quality,and population exposure

This paper establishes a link between an activity-based model for the Greater Toronto Area (GTA), dynamic traffic assignment, emission modelling, and air quality simulation. This provides agent-based output that allows vehicle emissions to be tracked back to individuals and households who are producing them. In addition, roadway emissions are dispersed and the resulting ambient air concentrations are linked with individual time-activity patterns in order to assess population exposure to air pollution. This framework is applied to evaluate the effects of a range of policy interventions and 2031 scenarios on the generation of vehicle emissions and greenhouse gases in the GTA. Results show that the predicted increase of approximately 2.6 million people and 1.3 million jobs in the region by 2031 compared to 2001 levels poses a major challenge in achieving meaningful reductions in GHGs and air pollution.     

Discretionary activity location choice: in-home or out-of-home?

This paper examines the location choice associated with discretionary activities (in-home vs. out-of-home). These substitution patterns are important in terms of travel demand as in-home activities do not necessitate travel while out-of-home activities incur travel. Mixed logit models are estimated using an activity dataset (2003 CHASE data) to analyze the factors associated with this choice at the individual activity-level. Results suggest that the attributes of an activity significantly contribute to understanding the likelihood of engaging in out-of-home activities. Activity type interaction terms reveal the varying influence that socio-demographics, activity attributes and travel have over four different activity types modeled. The results reveal that the location choice (in-home vs. out-of-home) is sensitive to travel characteristics. As the travel time and cost increases, an individual is less likely to engage in an activity out-of-home. Compared to passive and social activities, the location of active activities is more sensitive to changes in travel attributes.     

Modeling multi-unit vehicle dynamics for low-speed path-following assessment off-highway

This paper proposes a non-linear dynamics model for articulated vehicles. This model is able to capture common low-speed behaviours of any articulated vehicles off-highway, such as operating for a corner or roundabout on a cambered or slippery surface. It can be used to assess the low-speed manoeuvrability of articulated vehicles under such manoeuvres and conditions. The vehicle model was validated by comparing its path tracking performance to that of the field tests.     

按运量增长规划铁路牵引供电系统的发展

提出了确定铁路牵引供电系统发展最佳途径的课题，并建议采用动态规划法解决这一课题。     

Exact and simplified estimations for elastic buckling pressures of structural pipe-in-pipe cross sections under external hydrostatic pressure

Structural pipe-in-pipe cross sections have significant potential for application in offshore oil and gas production systems because they combine thermal insulation performance with structural strength and self weight in an integrated way. Such cross sections comprise inner and outer thin-walled pipes with the annulus between them fully filled by a selectable filler material to impart an appropriate combination of properties. Structural pipe-in-pipe cross sections can exhibit several different collapse mechanisms, and the basis of the preferential occurrence of one over the others is of interest. This article presents an exact analysis for predicting the elastic buckling behaviours of a structural pipe-in-pipe cross section when subjected to external hydrostatic pressure. Simplified approximations are also investigated for elastic buckling pressure and mode when the outer pipe and its contact with the filler material is considered as a pipe on an elastic foundation. Results are presented to show the variation of elastic buckling pressure with the relative elastic modulus of the filler and pipe materials, the filler thickness, and the thicknesses of the inner and outer pipes. Case studies based on realistic application scenarios are used to show that the simplified approximations are sufficiently accurate for practical structural design purposes.     

Second-order sum-frequency wave diffraction by a truncated surface-piercing cylinder in bichromatic waves

This work considers the second-order sum-frequency diffraction problem for a stationary truncated surface-piercing circular cylinder in bichromatic waves. The solution method was based on a semianalytical formulation of the second-order sum-frequency diffraction potential. The boundary conditions were properly satisfied by introducing the “locked” and the “free” wave components of the nonlinear velocity potential. The method was validated by comparing the calculated results with numerical data previously reported by other authors. Particular attention was paid to the second-order sum-frequency heave forces and the change in the wave run-up configuration due to the existence of the lower fluid domain underneath the truncated cylinder.