High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

Fuel consumption of fuel cell hybrid vehicles considering battery SOC differences

Fuel cell hybrid vehicles (FCHVs) have become one of the most promising candidates for future transportation due to current energy supply problem and environmental problem. Fuel economy is an important factor in FCHVs. In order to properly evaluate the fuel economy of an FCHV, the initial battery state of charge (SOC) and the final battery SOC have to be identical so that the effect of the battery energy usage on the fuel economy is neglected. In the simulation or in the real driving, however, the final battery SOC is usually different from the initial battery SOC, and the final battery SOC often depends on the power management strategy. To consider the difference between the two battery SOC values, the concept of equivalent fuel consumption is presented by two methods. One is based on the relationship between delta SOC and delta fuel consumption, and the other is based on the optimal control theory. Two rule-based power management strategies for an FCHV are presented, and for each strategy, the fuel economy is evaluated based on the two methods. The characteristics of the two methods are discussed and compared, and the superior one is selected based on the comparison.     

FE modeling method for a headform used in pedestrian protection simulations

Finite element models of headforms are used in experimental simulations of pedestrian protection. In this study, a quick and accurate method for FE modeling of the headforms was developed. This method entailed the initial definition of the dimensional parameters for the mass, centroid, and inertial moment properties of the headform. The equations governing these properties were constructed using the dimensional parameters as design variables. The dimensional parameters meeting the requirements of the relevant regulations were obtained by solving these three equations. A design optimization model was constructed for the material parameters of the outer part of the headform. In this model, the parameters of the material used in the FE model were considered as design variables; the difference between the peak acceleration in a side-impact simulation test and the average value of the regulated acceleration range was used as the objective function; the first-order natural frequency, which was required to be greater than 5,000 Hz, was defined as one of the constraints; the peak drop acceleration, which was required to be within the regulated range of values, was defined as the second constraint. The material parameters were obtained by solving the optimization model. These material parameters meet the dynamic requirements of the regulations for headforms. Based on these three parameters, an FE model of a headform can be constructed quickly and accurately.     

New lead-acid battery management system based on generator regulation

A novel regulation system for a vehicle generator and lead-acid battery is proposed in this paper. By integrating the regulation method, the output voltage of the generator is determined and controlled by the algorithm to save electrical energy and protect the lead-acid battery. The regulation algorithm is implemented in Matlab/Simulink, and the logic function of the system is verified using the dSPACE/AutoBox workbench. The experimental results show that the new algorithm improves the performance of the fuel economy of the vehicle and the battery state-of-health compared to the traditional control method.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Research progress and application of computational method for hydrodynamic noise from air-water interface北大核心CSCD

含水气界面水动力噪声是船海工程结构物经常遇到的一类典型重要噪声,具有机理复杂、声源形式多样、传播影响因素众多等特点。含水气界面水动力噪声与自由面相互作用,受空化、水气泡混合流等影响,对舰船的隐蔽性造成很多负面影响,具有重要的研究意义。分别从自由面噪声、空化噪声和水气泡混合流噪声3个方面进行介绍,并阐述相应噪声的计算方法以及在噪声计算时需要考虑的关键问题和目前所采用的解决方案。最后,展望未来的研究发展方向。     

Residual life prediction for marine diesel turbocharger based on Wiener process北大核心CSCD

[目的]针对船舶柴油机增压器难以收集到全生命周期性能退化数据的问题,提出一种基于维纳过程的寿命预测模型。[方法]首先,采用K-Means模型对增压器实际运行工况进行聚类,提取出典型工况数据;然后,使用贝叶斯突变点检测模型识别增压器的缺陷点;最后,建立基于维纳过程的退化模型,并以某型船用柴油机增压器为应用对象,预测增压器的剩余使用寿命。[结果]结果显示,基于维纳过程的寿命预测方法能够在不需要同类设备历史退化数据的情况下对增压器的剩余寿命进行预测。[结论]所提方法对缺少故障样本的船舶柴油机增压器寿命预测具有一定的参考价值。     

秦岭马白山隧道新型紧急救援站结构型式研究北大核心CSCD

针对艰险山区高速铁路隧道的防灾救援难题,文章依托秦岭马白山隧道,提出了适合该隧道的新型紧急救援站结构型式,并利用FDS软件模拟隧道内纵向通风时列车着火后的烟气扩散,确定了规范中尚未给出的紧急救援站隔离区长度参数。结果表明:(1)秦岭马白山隧道新型紧急救援站结构型式应包括疏散区、隔离区以及待避救援区;(2)利用FDS数值模拟时,在不考虑纵向通风下,烟气沿下坡方向的扩散长度为295 m;考虑沿下坡方向通风时烟气最远扩散长度为980 m,建议隔离区长度设置为1000 m。