Valuation of externalities through neo-classical methods by including institutional variables

Externalities are uncompensated influences that are not expressed in a market but that affect the production possibilities or the welfare level of third parties. An example is the noise pollution in airport areas. Although air transport is an important source of economic growth and employment in many countries, the social and environmental problems connected with this sector are rising rapidly. Consequently, airports are becoming a matter of concern to many politicians. On what kind of values should they base their decisions as to further growth or consolidation of the current situation? In this paper we discuss two approaches, one based on mainstream, neo-classical, economics, and one based on institutional approaches, more in particular new institutional economics, which can be seen as a development complementary to the mainstream.     

Hybrid Electric Drive for DDG-51 Class Destroyers

The first of the Arleigh Burke class destroyers is nearing its mid-life. This class of ships was designed during the late 1970s through the 1980s to meet the threats that were prevalent at that time. Since entering service in 1991, these ships have shown themselves to be extremely versatile and the class now consists of nearly 60 ships in service. Their combat systems have been continually upgraded and adapted to meet the new threats the United States faces today. However, in order to keep these platforms viable throughout the first half of the 21st century, their operating costs must be reduced. Manpower, maintenance, and fuel are three of the top operating cost drivers. Most surface combatants spend very little of their underway time operating at full speed or even close to that. Over 1/3 of their underway time is spent at 12 knots and under. This is less than half of their maximum speed and only a fraction of the maximum power owing to the cubic speed–power relationship. Although the existing mechanical drive system is reasonably efficient, the main gas turbines are extremely inefficient at these very low power levels. A shaft-mounted auxiliary electric propulsion system (EPS) can take advantage of excess capacity in the ship service generators to reduce the main engine operating hours. Enabling bi-directional power flow from this auxiliary electric drive will provide additional generation capacity for ship service loads at a modest additional cost. It also provides a "cross-connect" capability from one shaft to the other. This paper will explore one prospect for reducing the operating cost of the DDG-51 class of ships by installing an auxiliary EPS that would powered by the ship service electrical plant. This additional system would serve to reduce both underway fuel usage as well as maintenance on the gas turbine main engines by reducing the number of operating hours on each engine. We will examine the technology trade-offs in this ongoing study.     

Joint development at transit stations in the United States

Joint development, as the term is generally used in connection with transit systems in the United States, is real estate development that is closely linked to public transportation services and station facilities, and takes advantage of the market and locational advantages provided by them. Research conducted by LEK Associates for the Urban Mass Transportation Administration (UMTA) suggests that, in addition to helping shape urban growth and land development, joint development is also a surprisingly effective means of increasing transit system ridership and farebox revenues, as well as a source of increasingly significant revenues from the sale or lease of air rights.The completion of nine joint development projects in as many different cities, started under the former Urban Initiatives Program, for example, net additional annual ridership might reach 12000000 one-way trips. Net additional annual farebox revenues might reach over $9000000. This added revenue would be sufficient to repay the $62 million combined UMTA/transit operator investment in the nine projects, exclusive of the costs of the basic transit system improvements around which the projects are planned, in less than six years.Among transit authority-administered joint development programs examined in a separate study, the Washington Metropolitan Area Transit Authority (WMATA) has had the most success in generating significant value capture income. For example, the cumulative revenue realized by WMATA from just six joint development projects in the Washington, DC region, through September 1983 exceeded $ 6.9 million. Projections through fiscal year 1986 indicate cumulative revenues approximating $ 28 million will be received from developer leases.     

A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

Performance indicators for transit management

Transit performance can be evaluated through quantitative indicators. As the provision of efficient and effective transit service are appropriate goals to be encouraged by federal and state governments, these goals are used to develop performance indicators.Three efficiency and four effectiveness indicators are described, together with two overall indicators. These nine indicators are analyzed for comparability utilizing operating and financial data collected from public transit agencies in California.Performance indicators selected for this study should not be viewed as final. Twenty-one performance indicators proposed by previous studies were reviewed. Theoretical considerations and unavailability or unreliability of data caused omission of several useful measures like passenger-miles. Circumstances such as improved data, emphasis upon goals other than efficiency and effectiveness, and local conditions might warrant the inclusion of indicators deleted from this research.This paper is based on work conducted for the Urban Mass Transportation Administration under University Research and Training Grant CA-11-0014, Development of Performance Indicators for Transit. The views expressed herein are those of the authors and not necessarily those of the University of California or the United States Government. We are indebted to John Feren for assistance with the statistical processing and data gathering.     

Introduction: Habitual travel choice

In this introduction to the special issue on habitual travel choice, we provide a brief account of the role of habit in travel behaviour, discuss more generally what habitual choice is, and briefly review the issues addressed in the solicited papers. These issues include how habitual travel behaviour should be measured, how to model the learning process that makes travel choice habitual, and how to break and replace car-use habits.     

Habitual travel behaviour: Evidence from a six-week travel diary

This paper introduces different methods to measure similarity of travel behaviour addressing the question of how repetitious travel behaviour actually is. It compares empirical results of the different methods based on the data from a six-week travel diary. In general, the results show that the day-to-day behaviour is more variable if measured with trip-based methods instead of methods based on time budgets. Furthermore, it is confirmed that the similarity declines if the method captures more of the complexity of the travel pattern. It is also shown that travel behaviour is neither totally repetitious nor totally variable. Even for the whole observation period, it is demonstrated that two days always have some common elements. Additionally, it is found that the different methods yield the same pattern of variability for different types of day. Travel behaviour is clearly more stable on work days. Similar results for all methods are also obtained concerning the question of how long the minimum period of observation should be. All measures show that the period should not be less than two weeks if one aims at measuring variability.     

Process Save Reduction by Macro Joint Approach: The Key to Real Time and Efficient Vehicle Simulation

Applying a non-linear model reduction method to the tire suspension system of road vehicles enables an automatic transfer of complex offline simulation vehicle models to a mathematical model, which fits the real time simulation requirements. The basic assumption, that high frequent inner suspension dynamics are not relevant to handling manoeuvres, converts the differential algebraic equation system (DAE) of suspensions with kinematical closed loops into pure elasto-kinematical linkage equations. The equations of motions can be represented as an ordinary differential equation system (ODE) and considerable simulation time reductions are obtained for the off-line simulation and real time simulation is enabled. This so-called macro joint approach is an alternative modelling method to the well-known look-up table representation of suspension kinematics but it keeps the parameterisation of the original suspension model and is suitable to parameterised real time MBS models. With a second step the dynamics, caused by compliance in the suspension bushings, are reduced to their quasi-static behaviour. The consideration of these quasi-elasticity has nearly no influence on the necessary simulation time. This contribution shows the theoretical background and demonstrates the advantage of the macro joint model reduction approach on a typical vehicle example.