Development of a low-noise cooling fan for an alternator using numerical and doe methods

An alternator, which converts mechanical rotational energy into electrical energy, is an important component of a vehicle. Alternators operate over a broad range of rotational speeds, typically from 3,000 RPM to 18,000 RPM, which demands a cooling fan producing sufficient airflow, ideally with a minimum of noise. In the current study, an optimized alternator-cooling fan was developed through a linked DOE(Design OF Experiment) process and numerical analysis. The SC/Tetra and FlowNoise S/W programs were used to calculate flow rates and noise levels, respectively, for the newly developed fan. Compared with original model, the numerical results predicted a 3 dBA noise reduction; the measured reduction was 4 dBA.     

Tractor-semitrailer model for vehicles carrying liquids

This article presents a model for solving solid-fluid interactions in vehicles carrying liquids. A tractor-semitrailer model is developed by incorporating suspension systems and tire dynamics. Owing to the solid-fluid interaction, equations of motion for the vehicle system are coupled. To simplify the complicated solution procedure, the coupled equations are solved separately using two different codes. Each code is analyzed separately; but as the parameters of the two codes depend on each other, the codes must be connected at the end of each time step. To determine the dynamic behavior of the system, different braking moments are applied. As the braking moments increase, braking time decreases. However, it turns out that increasing the braking moment to more than a certain level produces no significant results. It is also shown that vehicles carrying fluids need a greater amount of braking moments in comparison to vehicles carrying solids during braking. In addition, as the level of the fluid inside the tanker increases, from one-third to two-third of the tanker's volume, the sloshing forces applied to the tanker's walls increase. It was also concluded that the strategy used in this article to solve for the solid-fluid interaction by incorporating vehicle dynamic effects represents an effective method for determining the dynamic behavior of vehicles carrying fluids in other critical maneuvers.     

Study of in-vehicle route guidance systems for improvement of right-side drivers in the Japanese traffic system

A country can adopt one of two standards for traffic flow — cars may travel on the left or right side of the road. When drivers who are accustomed to driving on the right side of the road drive on the left side, and vice versa, the mental workload is likely increased due to the driver’s unfamiliarity with a new language, the position of the driver’s seat, different driving directions, and other factors that differ from those of their home country. One method of doing this is to make sure that the in-vehicle route guidance information (RGI) is not overly complicated — thereby assisting drivers in improving their safety. Consequently, the aim of this study was to facilitate mobility and improve safety for natural right-side drivers driving temporarily in left-side traffic. In this study, driver behavior and workload — given various types of RGI — were evaluated in a driving simulator with a variety of prescribable test conditions. This research was composed of two experiments. In the first, various types of in-vehicle route guidance systems were tested and evaluated in terms of their characteristics and associated driver behaviors (while driving). In the second experiment, systemic factors and effectiveness were evaluated by two combined systems, arrow and map-type information, based on the results of the first experiment. In light of both experiments, the various types of route guidance systems were discussed in terms of their results. A navigation system was proposed to alleviate some of the secondary tasks such as route selection.     

软土地基水下真空预压固结离心模型试验

采用新发明的真空吸水系统应用于离心机中,可以使土体产生向上渗流并模拟软土地基真空预压。为获得理想的水下真空预压固结对比效果,竖井采用2种不同井间距的砂井,密封膜采用完全覆盖的形式。用发明的装置产生水下真空得以模拟软土水下固结行为。介绍了模型制作、试验程序及真空发生系统,并分析了孔隙水压力、变形、不排水剪切强度的改变和不同井间距对固结速率的影响。     

The construction and use of continuous autoregressive models for traffic indices

This article discusses the use of continuous autoregressive models to describe the behavior of traffic indices. From discretely sampled data, second-order differential equation models are constructed to represent dynamic traffic fluctuations as the response of a linear system to a stochastic forcing function. The results are compared to the more common M/G/∞ queueing model approach, and the analysis is demonstrated on time series of aircraft concentration in thirty-one enroute air traffic control sectors.     

Shipping and investment incentives: a trilogy Part 2. Investment incentives for shipping

This paper concentrates on the shipping industry and considers the forms of fiscal and financial incentives which are used by different governments to promote or encourage investment in their shipping industry. The analysis reduces the various packages of investment incentives and loan arrangements to a common measurement—the net present value of the package—and uses this to draw international comparisons and rankings. The results are based on different values of rates of return in the shipping industry and under certain assumptions concerning the rate of inflation and the rate of discount. Differences in loan arrangements have also been incorporated. The particular results are valid only for the specified circumstances but the methodology is generally applicable.     

Optimal Active Suspension Design Using a Frequency-shaping PID Filter

By the incorporation of frequency-shaping into the linear quadratic methods used in active suspension design it is possible to achieve improvements in both body frequency response and road-holding. The use of a PID filter for this purpose also leads to robustness of the system to disturbance forces. Zero steady-state deflections are achieved for applied body loads by the integral action with excellent attenuation of the transient response. The resulting system consists of a hydraulic actuator in parallel with a body spring of arbitrary stiffness and is optimal with equivalent full state feedback.     

Initial results from long-term measurements of atmospheric humidity and related parameters in the marine boundary layer at two locations in the Gulf of Mexico

Measurements of boundary layer moisture have been acquired from Rotronic MP-100 sensors deployed on two NDBC buoys in the northern Gulf of Mexico from June through November 1993. For one sensor, which was retrieved approximately 8 months after deployment, the post- and precalibrations agreed closely and fell well within WMO specifications for accuracy. The second sensor operated continuously from June 1993 to February 1997 (3.5 years). Buoy observations of relative humidity and supporting data were used to calculate specific humidity and the surface fluxes of latent and sensible heat. Specific humidities from the buoys were compared with observations of moisture obtained from nearby ship reports, and the correlations were generally high (0.7–0.9). Surface gravity wave spectra were also acquired. The time series of specific humidity and the other buoy parameters revealed three primary scales of variability, small (h), synoptic (days), and seasonal (months). The synoptic variability was clearly dominant and occurred primarily during September, October, and November. Most of the synoptic variability was due to frontal systems that dropped down into the Gulf of Mexico from the continental US followed by air masses which were cold and dry. Cross-correlation analyses of the buoy data indicated that: (1) the moisture field was highly coherent over distances of 800 km or more in the northern Gulf of Mexico; and (2) both specific humidity and air temperature served as tracers of the motion associated with propagating atmospheric disturbances. These correlation analyses also revealed that the prevailing weather systems generally entered the buoy domain from the South prior to September, but primarily from the North thereafter. Spectra of the various buoy parameters indicated strong diurnal and semidiurnal variability for barometric pressure and sea surface temperature (SST) and lesser variability for air temperature, wind speed and significant wave height. The surface fluxes of latent and sensible heat were dominated by the synoptic events which took place from September through November with the transfer of latent heat being primarily from the ocean to the atmosphere. Finally, an analysis of the surface wave observations from each buoy, which included calculations of wave age and estimates of surface roughness, indicate that major heat and moisture flux events coincide with periods of active wave growth, although the data were insufficient to identify any causal relationships.     

The Effect of Topboxes on Motorcycle Stability

Hot wire anenometry measurements have been made in the wake of a model motorcycle and rider mounted in a windtunnel. Only in tests with a topbox present is there clear evidence of eddy shedding. Calculations have been performed on the corresponding full-scale motorcycle to determine the frequencies of the weave and wobble modes. Comparison with the wake frequencies extrapolated to full size show that at speeds of 31-34 m/s they coincide with those of the wobble mode which is found to be efficiently coupled to the aerodynamic excitation.