Parameter matchin and optimization for a hydraulic power-assistant system

A hydraulic power-assist system is a hydraulic regeneration system that can significantly improve fuel economy when installed on a conventional bus operating in urban traffic. This paper presents a methodology for matching a new hydraulic power-assist system (HPA) to a conventional bus. The HPA and the conventional bus were modeled using the AMESim environment. The HPA was optimized using a simulation-based orthogonal design method with two indexes, the fuel economy and the acceleration performance. According to the simulation results, the volume of the accumulator was the primary factor affecting fuel economy, and the gear ratio of the transfer case was the primary factor influencing the acceleration performance. As a result, tradeoffs between the two indexes are required for a practical operational scenario. Experimental results demonstrated that the optimal HPA installed on a conventional bus was able to satisfy the acceleration performance requirement of the vehicle and also reduced fuel consumption by 25 percent.     

Robust lane markings detection and road geometry computation

Detection of lane markings based on a camera sensor can be a low-cost solution to lane departure and curve-over-speed warnings. A number of methods and implementations have been reported in the literature. However, reliable detection is still an issue because of cast shadows, worn and occluded markings, variable ambient lighting conditions, for example. We focus on increasing detection reliability in two ways. First, we employed an image feature other than the commonly used edges: ridges, which we claim addresses this problem better. Second, we adapted RANSAC, a generic robust estimation method, to fit a parametric model of a pair of lane lines to the image features, based on both ridgeness and ridge orientation. In addition, the model was fitted for the left and right lane lines simultaneously to enforce a consistent result. Four measures of interest for driver assistance applications were directly computed from the fitted parametric model at each frame: lane width, lane curvature, and vehicle yaw angle and lateral offset with regard the lane medial axis. We qualitatively assessed our method in video sequences captured on several road types and under very different lighting conditions. We also quantitatively assessed it on synthetic but realistic video sequences for which road geometry and vehicle trajectory ground truth are known.     

多种交通方式下的城市空间分配

从集计角度分析了运行多种交通方式的城市交通系统。利用目前已受关注的宏观基本图（简称MFD）,描述城市交通的整体特性。以旧金山某区为例,使用现有数据,通过仿真论证如何应用MFD监管真实交通网络。然后讨论了同一路网中不同交通方式间如何相互作用,以及如何将这些作用纳入包含多种交通方式路网的MFD。研究得到的两个主要结论是：1）证实了已有研究猜想——对市区拥挤区域限行,可提高包括被限行者在肉的所有出行者的机动性;2）公交方式提供专用道路空间可提高所有交通方式的可达性。     

Rail infrastructure,ITS and access charges

This paper presents an overview of the principles and technologies relating to railway infrastructure. Specifically this paper includes rail–wheel contact, inspection and maintenance of rail. Intelligent transport systems (ITS) and their applications for the purposes of the railway transport in Europe are discussed. The potential, levels of development, technological and operational characteristics of the European Railway Traffic Management System (ERTMS) are presented. Finally, a discussion on methodologies, principles and current practices for access charging in Europe is provided.     

Numerical prediction of the modal response of flexible cylinders in cross-flow with a current dependent form of damping

A quadratic eigenvalue problem (QEP) was posed in order to study the dynamics of flexible cylinders in cross-flow, simulating slender offshore structures such as risers, catenaries or tendons. The Euler–Bernoulli equation was used to model the structure assuming a fluid loading model, and yielding a quadratic eigenvalue problem that included a form of damping dependent not only on the structural damping itself, but also on the free stream velocity and the fluid force coefficients. We solved the QEP using the finite element method. We also derived a simplified analytical solution in this work for comparison with the QEP, however this solution does not consider changes in tension along the length of the cylinder as the QEP does. In our study, the QEP solutions were first validated against the simplified analytical solution, and also against a well-known experimental dataset obtained in 2003, in which a flexible circular cylinder model was used to model the dynamics of a riser undergoing multi-mode vortex-induced vibrations.     

EFD and CFD for KCS heaving and pitching in regular head waves

The KCS container ship was investigated in calm water and regular head seas by means of EFD and CFD. The experimental study was conducted in FORCE Technology’s towing tank in Denmark, and the CFD study was conducted using the URANS codes CFDSHIP-IOWA and Star-CCM+ plus the potential theory code AEGIR. Three speeds were covered and the wave conditions were chosen in order to study the ship’s response in waves under resonance and maximum exciting conditions. In the experiment, the heave and pitch motions and the resistance were measured together with wave elevation of the incoming wave. The model test was designed and conducted in order to enable UA assessment of the measured data. The results show that the ship responds strongly when the resonance and maximum exciting conditions are met. With respect to experimental uncertainty, the level for calm water is comparable to PMM uncertainties for maneuvering testing while the level is higher in waves. Concerning the CFD results, the computation shows a very complex and time-varying flow pattern. For the integral quantities, a comparison between EFD and CFD shows that the computed motions and resistance in calm water is in fair agreement with the measurement. In waves, the motions are still in fair agreement with measured data, but larger differences are observed for the resistance. The mean resistance is reasonable, but the first order amplitude of the resistance time history is underpredicted by CFD. Finally, it seems that the URANS codes are in closer agreement with the measurements compared to the potential theory.     

Are Longer and Heavier Vehicles (LHVs) Beneficial for Society? A Cost Benefit Analysis to Evaluate their Potential Implementation in Spain

Abstract

In this paper we carry out a thorough review of the current research related to the benefits and costs arising from the implementation of longer and heavier vehicles (LHVs). From this review we concluded that despite the many studies available, little has been said about the sensitivity of the benefits and costs to the ultimate performance of the key variables related to the evolution of the economy, road transport performance, safety, and so on. In order to fill this gap, we have designed a sensitivity approach based on a cost benefit analysis tool to determine which variables demonstrate the greatest influence on the benefits and costs stemming from the implementation of LHVs. In order to test the methodology, we have used it in an analysis of the Spanish trunk network. The results show that the benefits of LHVs for society are significant. Even in the least favorable scenario, the economic benefits are greater than €3500 million over 15 years, and the environment enhanced as well, for CO₂ emissions are reduced by 2 Million tonnes. Overall we noted how the results are not very sensitive to the evolution of key variables in determining the final outcome. However, we found that the variables that have the greatest affect on the final benefit, such as traffic growth and social discount rate, depend basically on the performance of the overall economy. Moreover, the private cost for haulers seems to be more important in determining the final benefit than externality costs.     

A Modeling Framework for Bus Rapid Transit Operations Evaluation and Service Planning

Abstract

In this paper, we present a dynamic traffic assignment-simulation modeling framework (DYNASMART-P) to support the evaluation and planning of Bus Rapid Transit (BRT) services in urban transportation networks. The model represents the different characteristics associated with BRT operations such as: exclusive right-of-way lanes, limited-stop service, signal prioritization at congested intersections, and enhanced bus stops to reduce passenger boarding times. A set of simulation experiments is conducted using the model to study the impact of introducing a hypothetical BRT service in the Knoxville area in the State of Tennessee. In these experiments, the different operational characteristics of BRT are evaluated in terms of potential impact on transit ridership and on the interacting auto traffic. The results illustrate the advantages of BRT for increasing transit ridership and improving overall system performance.     

Optimization of Fare Structure and Service Frequency for Maximum Profitability of Transit Systems

Abstract

Providing efficient public transportation has been recognized as a potential way of alleviating congestion, improving mobility, mitigating air pollution, and reducing energy consumption. Many people use public transportation systems for their daily commute, while others use different transportation modes (e.g. cars, taxis, carpools, etc.). Inexpensive fares with good transit service encourages ridership, and the resulting revenue may be used to provide better service. Optimization of transit service frequency and its associated fare structure is desirable in order to increase revenue at reasonable transit operating expenditure. The objective of the study reported here is to maximize profit subject to service capacity constraint, while elastic demand is considered. The solution methodology is developed and applied to solve the profit maximization problem in a case study based on Newark, NJ, USA. Numerical results, including optimal solutions and sensitivity analyses, are presented. It is found that an optimal temporal headway and differential fare structure that maximizes total profit for the studied subway system can be efficiently solved.     

In-vehicle technology for self-driving cars: Advantages and challenges for aging drivers

The development of self-driving cars or autonomous vehicles has progressed at an unanticipated pace. Ironically, the driver or the driver-vehicle interaction is a largely neglected factor in the development of enabling technologies for autonomous vehicles. Therefore, this paper discusses the advantages and challenges faced by aging drivers with reference to in-vehicle technology for self-driving cars, on the basis of findings of recent studies. We summarize age-related characteristics of sensory, motor, and cognitive functions on the basis of extensive age-related research, which can provide a familiar to better aging drivers. Furthermore, we discuss some key aspects that need to be considered, such as familar to learnability, acceptance, and net effectiveness of new in-vehicle technology, as addressed in relevant studies. In addition, we present research-based examples on aging drivers and advanced technology, including a holistic approach that is being developed by MIT AgeLab, advanced navigation systems, and health monitoring systems. This paper anticipates many questions that may arise owing to the interaction of autonomous technologies with an older driver population. We expect the results of our study to be a foundation for further developments toward the consideration of needs of aging drivers while designing self-driving vehicles.