D9L推土机铸造铲刃,铲角的研制

在检测分析进口抗磨件基础上,采用空冷贝氏体铸钢制造了D9L推土机铲刃、铲角.实验室试验及1200h运行试验结果表明,国产件的性能和使用寿命均不低于进口产品.     

Effect of Connecting the Front and Rear Air Suspensions of a Vehicle on the Transmissibility of Road Undulation Inputs

Airsprings have been used for vehicle suspensions over the last 40 years. They are mostly used as independent suspensions. Analysis of air springs available in literature is mostly limited to a single-degree-of-freedom system or a two-degrees-of-freedom system only in the translation mode. This paper deals with a model of a vehicle where the front and the rear springs are connected by a capillary tube. A two-degrees-of-freedom model having motion in bounce and pitch mode is presented. Equations of mass flow are linearized on the assumption of small variations in volume and pressure. Expressions for the transmissibility and the phase angle in the bounce and the pitch mode are derived. Road inputs to the front and the rear axles are assumed to be identical except for a phase difference between them. The effect of the capillary flow coefficient and that of the phase angle between the front and the rear axle excitation are studied. It is shown that an optimum value of the capillary flow coefficient exists which minimizes the transmissibility of motion in both modes over the entire frequency range. It is also observed that a phase angle of 180 degrees presents ideal transmissibility characteristics. Thus, a promising application of air springs for a vehicle suspension is presented.     

出口苏丹米轨平车研制

介绍了出口苏丹米轨平车的技术参数、结构特点和试制情况。     

水中充液方箱振动和声辐射的有限元分析

针对水中充液方箱模型,进行了结构振动特性和受激声辐射特性的有限元数值分析.分别计算了结构物在空气与水中固有频率以及结构声辐射的声强级的频率响应.比较了附连水对结构物固有频率的影响.比较计算结果表明ANSYS对流固耦合的处理是可信的.     

低噪声车轮的原理、试验及应用前景

通过理论分析和试验，对欧洲近几年的几种低噪声车轮的设计原理及试验效果做出了评价，对低噪声车轮在货运及高速运输中的应用前景做了分析。     

The influence of food quality on the nutritional acclimation of the copepod Acartia clausi

The influence of food quality on the nutritional metabolism of Acartia clausi was studied experimentally using four different diets: (1) diatom cells of Thalassiosira weissflogii, (2) detritus prepared from the same culture, (3) 50 : 50 mix on a protein basis of the two previous diets, and 4) dinoflagellate cells of Prorocentrum micans. For each trophic, ingestion, gut transit time, trypsin activity and K_m (half saturation constant) were measured at limiting and saturating concentration. Assimilation rates were also estimated for both pure diatoms and mixed live–detrital cell diets. Ingestion followed a Holling type 2 response for diets 1 and 4, a linear one for detritus and an intermediate response for diet 3. Gut transit time displayed different adaptive changes with food regime depending on protein concentration. Trypsin activity was lower for detrital food and trypsin K_m significantly decreased with increasing concentration of live diatoms. Assimilation rates were higher for live food than for mixed live–detrital food. Results illustrated that Acartia-type copepods optimize nitrogen or protein uptake. They suggest that besides chemoreception-mediated selectivity, internal controls by digestion and assimilation also regulate ingestion (feed-back).     

Application of new parameterizations of gas transfer velocity and their impact on regional and global marine CO2 budgets

One of the dominant sources of uncertainty in the calculation of air–sea flux of carbon dioxide on a global scale originates from the various parameterizations of the gas transfer velocity, k, that are in use. Whilst it is undisputed that most of these parameterizations have shortcomings and neglect processes which influence air–sea gas exchange and do not scale with wind speed alone, there is no general agreement about their relative accuracy.The most widely used parameterizations are based on non-linear functions of wind speed and, to a lesser extent, on sea surface temperature and salinity. Processes such as surface film damping and whitecapping are known to have an effect on air–sea exchange. More recently published parameterizations use friction velocity, sea surface roughness, and significant wave height. These new parameters can account to some extent for processes such as film damping and whitecapping and could potentially explain the spread of wind-speed based transfer velocities published in the literature.We combine some of the principles of two recently published k parameterizations [Glover, D.M., Frew, N.M., McCue, S.J. and Bock, E.J., 2002. A multiyear time series of global gas transfer velocity from the TOPEX dual frequency, normalized radar backscatter algorithm. In: Donelan, M.A., Drennan, W.M., Saltzman, E.S., and Wanninkhof, R. (Eds.), Gas Transfer at Water Surfaces, Geophys. Monograph 127. AGU,Washington, DC, 325–331; Woolf, D.K., 2005. Parameterization of gas transfer velocities and sea-state dependent wave breaking. Tellus, 57B: 87–94] to calculate k as the sum of a linear function of total mean square slope of the sea surface and a wave breaking parameter. This separates contributions from direct and bubble-mediated gas transfer as suggested by Woolf [Woolf, D.K., 2005. Parameterization of gas transfer velocities and sea-state dependent wave breaking. Tellus, 57B: 87–94] and allows us to quantify contributions from these two processes independently.We then apply our parameterization to a monthly TOPEX altimeter gridded 1.5° × 1.5° data set and compare our results to transfer velocities calculated using the popular wind-based k parameterizations by Wanninkhof [Wanninkhof, R., 1992. Relationship between wind speed and gas exchange over the ocean. J. Geophys. Res., 97: 7373–7382.] and Wanninkhof and McGillis [Wanninkhof, R. and McGillis, W., 1999. A cubic relationship between air−sea CO2 exchange and wind speed. Geophys. Res. Lett., 26(13): 1889–1892]. We show that despite good agreement of the globally averaged transfer velocities, global and regional fluxes differ by up to 100%. These discrepancies are a result of different spatio-temporal distributions of the processes involved in the parameterizations of k, indicating the importance of wave field parameters and a need for further validation.