Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

The merits of accelerated depreciation for promoting investment in clean transport technologies: A simulation study in the Australian rail freight industry

This article ascertains the viability of promoting accelerated depreciation for newly acquired locomotives and other rolling stock as a means of encouraging technological investment in more efficient and environmentally friendly assets. The study uses a tax-adjusted asset replacement model to evaluate the merits of accelerated depreciation, and then compares the outcomes with alternative incentive schemes. It also examines what would occur if various schemes were used simultaneously.     

特种弹药铁路运输可调式定位装置研究

概述了特种弹药铁路运输可调试定位装置的主要功能、技术要求、主要战技术指标，介绍了特种弹药铁路运输采用的从箱体顶部固定方式，并进行了相应的可调式定位装置研究，将装置分为整体固定和单点独立固定两种，用于固定弹箱在敞车内的位置，确保弹体运输安全。     

Redefining activity types: Who participates in which leisure activity?

This paper analyzes the activity choices of individuals and the links between socio-demographics, daily schedules and activity attributes using a new activity choice framework. Activities are first clustered into groups based on their salient attributes, such as duration, frequency, flexibility, planning times, and number of involved persons, rather than their functional types (work, leisure and household obligations), using a K-means cluster technique. This led to the creation of several new activity groups such as “long, temporally fixed, personally flexible activities”, “short and flexible activities”. These activity groups form the choice set for the mixed logit activity choice modeling structure developed for the leisure activities in the second part of the paper. The model results reveal the significant relationships between socio-demographics, temporal characteristics, and characteristics of the schedules on leisure activity choice. The results demonstrate how changing demographics and other activities in individuals’ schedules may affect the nature of the leisure activities and present the substitution and complimentary effects that these new activity groups have on one another.     

关于沥青混凝土路面的常见病害及防治措施

沥青混凝土路面主要应用于公路的面层,由于沥青混凝土材料本身的差异,以及受设计、施工水平的影响,沥青路面常常出现松散、脱皮、冻胀翻浆、水破坏、沉陷、开裂、泛油、坑槽等病害。这些病害的出现严重影响了路面行车速度、行车安全、加大了汽车磨损、缩短了沥青路面的使用寿命,使行车不畅,行成交通压力,造成道路使用年限缩短。本文具体结合工程项目阐述沥青混凝土的施工工艺、病害分析及防治措施。     

Analysis of the effectiveness of control measures to mitigate road dust emissions in a regional network

The effectiveness of control measures to reduce road dust emissions is analyzed using a year’s data of road dust emissions collected with a mobile sampling platform and a survey of road maintenance practices in the Lake Tahoe Basin of Nevada and California US. Attributes such as sweeping practices, anti-icing, shoulder improvement, pavement condition, trackout, and abrasive material from road segments were analyzed with a feature subset selection algorithm. Street sweeping was found to be an effective means of controlling dust emissions from roads. Road dust from dirty tertiary roads served as a continuous source of suspendable material for adjacent high-speed roads in the winter time. To be most effective, emission control strategies require that not only primary roads, but all roads be swept after snow storms to recover applied abrasive material.     

Effect of interference fits on the fatigue lives of bolted composite joints

The effect of interference fits on the fatigue lives of bolted composite joints is investigated by conducting mechanical tests. Static and fatigue tests are carried out on specimens made of carbon-bismaleimide composites joined together as double-lap single-bolt joints. The bolts having interference fits ranging of 0 (neat fit), 0.5%, 0.75% and 1% are performed. The results demonstrate the relationship between fatigue life and different values of interference fits. After the fatigue tests, non-destructive evaluation (NDE) and scanning electron microscope (SEM) are used to observe the damage of the surrender and surface of the hole. The test results show that the interference fitted specimens have improved fatigue life compared to the neat fitted specimen. The NDE and SEM results reveal that the damage degree of interference fitted specimen is weaker than that for the neat fitted one.     

Delivering mobility as a service (MaaS) through a broker/aggregator business model

Transportation - Mobility as a service (MaaS) promises a bold new future where bundled public transport and shared mobility options (carsharing, ridesharing, bikesharing and microtransit) will...     

Two degree of freedom flow-induced vibration of cylindrical structures in marine environments: frequency ratio effects

The flow-induced vibration of a cylindrical structure is a very common problem in marine environments such as undersea pipelines, offshore risers, and cables. In this study, the vortex-induced vibration (VIV) of an elastically mounted cylinder at a low Reynolds number is simulated by a transient coupled fluid–structure interaction numerical model. Considering VIV with low damping ratio, the response, hydrodynamic forces, and vortex shedding modes of the cylinder is systematically analyzed and summed up the universal rule under different frequency ratios. On the basis of the analysis, we find that the frequency ratio α is a very important parameter. It decides the locked-in, beat, and phase-switch phenomena of the cylinder, meanwhile, it also influence the vortex mode of the cylinder. The trajectory of the two degrees of freedom (2 DOF) case at different natural frequency ratios is discussed, with most trajectories having a “figure of 8” shape and a few having a “crescent” shape. A fast Fourier transformation technique is used to obtain the frequency characteristics of the vibration of the cylindrical structure. Using the 2 DOF cylinder model in place of the 1 DOF model presents several advantages in simulating the nonlinear characteristics of cylindrical structures, including the capacity to model the crosswise vibration generated by in-line vibration.