基床式基础防波堤的动力软化判别标准的研究

以长江口深水航道治理二期工程为依托,进行基床基础防波堤的动力软化判别标准的研究,分析在波浪作用下3个不同沉降量的典型断面下卧地基土的自重应力、附加静应力、波浪作用的附加动应力分布间的关系,初步得出该地区软粘土可能出现动力软化现象的判别标准。     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Buck斩波电路电流连续与电流断续的比较研究

对降压斩波电路负载加反电动势其电流在不同情况下发生的连续和断续现象进行了研究。根据分段线性化思想,推断出降压斩波电路输出电流在断续情况下的条件,给出了其在电流断续的计算公式,为其实际应用提供了方便。     

公路隧道双洞互补式通风适用性分析

为研究公路隧道双洞互补式通风的适用性,文章基于隧址海拔和温度、隧道长度和纵坡、隧道交通量和交通组成、隧道双洞间距等因素对互补式通风负荷比及通风效果的影响进行计算分析。研究结果表明:当隧道上下行通风负荷比大于1.5或隧道单向纵坡绝对值在1.5%~2.0%之间时,适宜采用互补式通风;隧道长度在4.5~6 km之间时,采用双洞互补式通风最经济实用;交通量和交通组成的影响关系显示隧道大型车混入率在35%~50%之间时宜考虑采用互补式通风;双洞隧道适合采用互补式通风的最小间距为30 m。     

调距桨桨叶连接螺栓过渡圆角光弹性试验研究

苛刻的空间尺寸要求和严酷的使用环境使得调距桨桨叶连接螺栓设计极为重要,为研究连接螺栓螺帽螺杆圆角过渡区域因截面形状突变存在的应力集中情况和应力分布规律,以某型调距桨桨叶连接螺栓联接组件作为试验模型,采用光弹性试验方法测得其应力分布和应力集中系数,并与有限元仿真分析结果进行了对比验证,为桨叶连接螺栓组件结构设计及其优化提供重要支撑。     

高压共轨电控喷射柴油机

简述高压共轨柴油发动机组成、原理及特点,并介绍其发展趋势,对推广使用高压共轨柴油发动机具有指导意义。     

电压型三相H桥逆变器直流支撑电容容值优化

直流支撑电容是电压型逆变器的重要组成部分,其选型直接影响到逆变器的电气性能以及整机功率密度.针对三相H桥逆变器,提出了一种通过相间载波移相减小支撑电容谐波电流的方法.采用开关函数法和双重傅里叶级数分析了逆变器支撑电容电流的主要谐波成分,给出了优化电容容值的计算方法.通过仿真对比相间载波移相前后,保持直流母线波动幅值一致...     

水轮发电机组阻尼绕组连接片的包辛格效应

研究了水轮发电机组阻尼绕组连接片材料在不同压缩变量和反向应变量下所导致的应变抗力减小的现象(称为包辛格效应,简称BE),并探讨了不同压缩应变量对阻尼绕组连接片BE的影响,通过不同压缩应变量压拉实验,找到阻尼绕组紫铜连接片的最优包辛格值。结果表明:较大压缩变量对BE存在影响,随预变形量的增加,包辛格效应值变化,预变形量为3%时,包辛格效应值达到极值。再增加变形量,包辛格效应值减小,3%为最优变形量,即阻尼绕组失效界限值。     

扣式锌银二次电池锌负极性能的研究

本文研究在锌粉中添加氧化铅后分别加入银粉、锡酸钠、氢氧化钙、及氧化铝制备不同组成的锌负极的性能,对合成的锌负极的析气量进行了检测分析,对组成的XR41电池循环性能进行研究.结果表明,锌粉中添加氧化铅、锡酸钠的锌负极析气量最小,为0.16 ml/(2g·10d).制备的电池具有较好的循环寿命.     

水中悬浮隧道管段接头的力学特性分析

文章通过解析方法和数值方法对悬浮隧道管段接头的力学特性进行了分析,旨在探讨影响管段接头力学特性的因素和规律,同时对两种方法进行了分析和比较.