桥头搭板受力特性及适应性

运用MARC软件,通过研编用户子程序模拟车辆的移动荷载,应用迭代接触算法Contact和单元生死技术模拟搭板与填土之间接触和脱空的不同受力状态,并基于均匀沉降和不均匀沉降两种地基模式,考虑搭板受力和变形的耦合,分析了搭板的受力特性和适应性。当脱空长度在1.08 m范围内时,板底弯拉应力值与完全弹性支承时相等,但随着脱空长度的继续增大而显著增大,完全脱空时板底弯拉应力与简支板相等,板底最大弯拉应力的荷载作用位置在桥台与1/2板长之间。搭板对地基沉降的适应性表现为:长度6 m的搭板适用于处理地基沉降在3 cm以内的桥头路段;8 m长度的搭板适用于处理地基沉降在4 cm以内的桥头路段,而10 m搭板适用于处理地基沉降在5 cm以内的桥头路段。     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Buck斩波电路电流连续与电流断续的比较研究

对降压斩波电路负载加反电动势其电流在不同情况下发生的连续和断续现象进行了研究。根据分段线性化思想,推断出降压斩波电路输出电流在断续情况下的条件,给出了其在电流断续的计算公式,为其实际应用提供了方便。     

公路隧道双洞互补式通风适用性分析

为研究公路隧道双洞互补式通风的适用性,文章基于隧址海拔和温度、隧道长度和纵坡、隧道交通量和交通组成、隧道双洞间距等因素对互补式通风负荷比及通风效果的影响进行计算分析。研究结果表明:当隧道上下行通风负荷比大于1.5或隧道单向纵坡绝对值在1.5%~2.0%之间时,适宜采用互补式通风;隧道长度在4.5~6 km之间时,采用双洞互补式通风最经济实用;交通量和交通组成的影响关系显示隧道大型车混入率在35%~50%之间时宜考虑采用互补式通风;双洞隧道适合采用互补式通风的最小间距为30 m。     

极地破冰船锚系交互设计技术的拉锚动力学仿真

基于三维交互设计与起抛锚运动数字化验证技术,研究极地破冰船的锚泊系统设计与起抛锚运动状态。通过三维交互建模及计算机模拟可真实地反映锚的翻转运动状态及收藏贴合情况,如果设计不完善,可以直接从工程图看出不贴合位置,量出间隙量,有助于加速设计方案的修改。三维虚拟仿真试验可每次提供不同角度、方位的仿真试验结果,为提高船舶的设计效率提供可靠的工具。     

调距桨桨叶连接螺栓过渡圆角光弹性试验研究

苛刻的空间尺寸要求和严酷的使用环境使得调距桨桨叶连接螺栓设计极为重要,为研究连接螺栓螺帽螺杆圆角过渡区域因截面形状突变存在的应力集中情况和应力分布规律,以某型调距桨桨叶连接螺栓联接组件作为试验模型,采用光弹性试验方法测得其应力分布和应力集中系数,并与有限元仿真分析结果进行了对比验证,为桨叶连接螺栓组件结构设计及其优化提供重要支撑。     

基于远、近期合建的折多山公路隧道总体设计方案研究

为解决特长公路隧道升级改造困难问题,以折多山公路隧道项目为依托,创新性地提出远、近期合建的总体设计方案。通过交通量预测、工程造价、运营通风及逃生救援等方面综合比较,得出可实施的合建方案： 先期建设二级公路隧道主洞,设2段非贯通平导,后期直接将二级公路隧道作为高速公路隧道右洞,并贯通二级公路隧道平导作为高速公路隧道左洞。合建方案能有效节约工程造价,降低社会耗能。     

高压共轨电控喷射柴油机

简述高压共轨柴油发动机组成、原理及特点,并介绍其发展趋势,对推广使用高压共轨柴油发动机具有指导意义。     

电压型三相H桥逆变器直流支撑电容容值优化

直流支撑电容是电压型逆变器的重要组成部分,其选型直接影响到逆变器的电气性能以及整机功率密度.针对三相H桥逆变器,提出了一种通过相间载波移相减小支撑电容谐波电流的方法.采用开关函数法和双重傅里叶级数分析了逆变器支撑电容电流的主要谐波成分,给出了优化电容容值的计算方法.通过仿真对比相间载波移相前后,保持直流母线波动幅值一致...     

舰机协同反潜导航问题研究

文章从目前舰机协同反潜中存在的导航精度不高和抗干扰性差的问题出发,分析了影响反潜导航的因素,提出了应用舰艇编队雷达组网方法提高导航能力的思路。