Model based burnt gas fraction controller design of diesel engine with VGT/Dual loop EGR system

-Recently, regulation of NOx and PM emission in diesel engines has become stricter and the EGR system has been expanded into a dual loop EGR system to increase EGR rate as well as to utilize exhaust gas strategically. In terms of engine combustion characteristics, burnt gas fraction is becoming an important factor of solving the NOx and PM emission reduction problem more efficiently but conventional controller focused only pressure and air flow rate targets. Unlike the previous studies, this paper describes a model based burnt gas fraction control structure for a diesel engine with a dual loop EGR and a turbocharger. Feedforward control inputs based on burnt gas fraction states aids in the precise control of diesel engines, especially in transient states by considering coupled behavior within the system. For the controller validation, a control oriented reduced order model of a diesel engine air management system is established to simplify the control input computation and its stability is proved by analysing the internal dynamics stability. Then, a sliding mode controller is designed and controller robustness at certain operating points is validated using an HiLS bench.     

Combined control of a regenerative braking and antilock braking system for hybrid electric vehicles

Most parallel hybrid electric vehicles (HEV) employ both a hydraulic braking system and a regenerative braking system to provide enhanced braking performance and energy regeneration. A new design of a combined braking control strategy (CBCS) is presented in this paper. The design is based on a new method of HEV braking torque distribution that makes the hydraulic braking system work together with the regenerative braking system. The control system meets the requirements of a vehicle longitudinal braking performance and gets more regenerative energy charge back to the battery. In the described system, a logic threshold control strategy (LTCS) is developed to adjust the hydraulic braking torque dynamically, and a fuzzy logic control strategy (FCS) is applied to adjust the regenerative braking torque dynamically. With the control strategy, the hydraulic braking system and the regenerative braking system work synchronously to assure high regenerative efficiency and good braking performance, even on roads with a low adhesion coefficient when emergency braking is required. The proposed braking control strategy is steady and effective, as demonstrated by the experiment and the simulation.     

Review of research on ship flow field measurement technology北大核心CSCD

通过对舰船周围流场信息进行精细化描述,即可从流动机理角度反馈舰船宏观水动力表现的内在本质,而优质的流场测试技术是保证流场精细化描述的必要手段。从舰船流场测试的工程需求出发,根据技术特点梳理现阶段舰船流场试验测试技术的发展现状、应用场景及特性问题,建议从硬件升级与技术融合、算法更迭与功能扩展、数据同化与机器学习等角度切入,以推动流场测试技术朝着综合性、专业化、高效化等方向快速发展。     

Numerical analysis of transient fluid-structure interaction of warship impact damage caused by underwater explosion using the FSLAB北大核心CSCD

［Objectives］This paper aims to address the numerical simulation problems of the dynamic response of ships subject to near-, medium- and far-field underwater explosions by establishing several numerical methods and calculation models. ［Methods］First, load and fluid-structure interaction models are established on the basis of the Eulerian finite element method and acoustic finite element method using the field-split technique, and FSLAB fluid-structure interaction software is developed. Next, near-, medium- and far-field underwater explosions are numerically simulated respectively. The shock wave propagation law, bubble shape and load evolution characteristics of near free-surface and near-wall underwater explosions are obtained, and the shock response characteristics of a spherical shell and ship subject to far-field underwater explosions are analyzed. Finally, the FSLAB software results are compared with the analytical solutions, reference solutions and experimental data. ［Results］The results show that the FSLAB fluid-structure interaction software developed in this paper is effective and accurate in simulating the impact damage of underwater explosions on warships. ［Conclusion］This study can provide a basis and support for the power assessment of underwater anti-explosion and shock design of warships. © 2022 Journal of Clinical Hepatology. All rights reserved.     

某富水断层隧道涌水治理方案优化分析及工程应用北大核心CSCD

以武九高速高楼山公路隧道为例,针对以断层破碎带为主控因素的隧道突水治理问题展开数值分析研究。基于FLAC 3D有限差分法及流固耦合分析原理,研究了导水洞排水、注浆堵水和排堵结合等不同治理方式对隧道涌水量及围岩稳定性的影响。结果表明:对于富水断层隧道发生A、B级别的大量涌水时,建议同时采取导水洞排水、注浆堵水的排堵结合措施,导水洞设置在近断层处,且与隧道相对距离为0.75(D+l),注浆圈厚度控制在7 m以内,注浆圈相对渗透系数比不超过10,既能降低涌水量,又能保证围岩的稳定性;对于C级涌水隧道,可采取注浆措施,注浆厚度不低于3 m,相对渗透系数不低于20;对于D级及以下涌水隧道,采取常规抽排水措施即可。     

Review of ship slamming loads and responses

The paper presents an overview of studies of slamming on ship structures. This work focuses on the hull slamming, which is one of the most important types of slamming problems to be considered in the ship design process and the assessment of the ship safety. There are three main research aspects related to the hull slamming phenomenon, a) where and how often a slamming event occurs, b) slamming load prediction and c) structural response due to slamming loads. The approaches used in each aspect are reviewed and commented, together with the presentation of some typical results. The methodology, which combines the seakeeping analysis and slamming load prediction, is discussed for the global analysis of the hull slamming of a ship in waves. Some physical phenomena during the slamming event are discussed also. Recommendations for the future research and developments are made.     

Investigation and analysis of high temperature corrosion and degradation of marine boiler combustion swirler

The present paper investigated and analyzed swirler material consisting of mild steel which was subjected to service for the period of one year in a 30 MW marine boiler. Due to the presence of high temperatures in the furnace coupled with the corrosive marine environment swirler material showed accelerated degradation and material wastage. An investigation into the feasibility of manufacturing the existing swirler with an alternate material or coating the swirler material with a thermal barrier coating was undertaken. Based on their properties and performance, SS 304 and SS 316 were proposed as the replacement materials for the swirler. The other alternative of coating the existing swirlers with a form thermal barrier coating to observe for any improvement in their performance at elevated temperatures was also tested. Stellite, which is a Ni-Co based coating, was carried out on the MS samples and the same were exposed to same temperatures mentioned above. The performance of the available options was evaluated with respect to the grain structure of the material, the hardness value of the materials and deterioration at elevated temperatures. Investigation showed the proposed materials/coatings like SS 304, SS 316 and Stellite coating revealed that SS 316 is the material best suited for high temperature application.     

Thoughts on development of modern ship technology北大核心CSCD

随着海上新质作战概念的不断革新,现代海战形态呈现出多域攻防、分布协同、高效杀伤的特点,正在加速推进新型水面舰船技术的创新发展。围绕作战空间、作战体系结构、作战单元、作战武备等方面,总结归纳现代海上新质作战概念的主要特征,梳理水面舰船的体系定位及作战能力演变,系统分析新型水面舰船装备发展的主要特征,提出关于发展水面舰船总体集成技术、网络信息技术、数智赋能技术、新型能源保障技术、先进材料技术、环保节能技术的若干思考。     

CMC改性海水泥浆性质变化及砂地层成膜试验研究北大核心CSCD

为探究泥水盾构穿越海底砂地层时羧甲基纤维素钠(CMC)对海水泥浆性质及成膜效果的影响,配制不同CMC掺量的海水泥浆,分析泥浆泌水率、黏度、Zeta电位等性质的变化情况,并开展了泥浆渗透成膜试验。研究结果表明:相对于海水泥浆,加入CMC后的泥浆黏度逐渐增大,2h泌水率显著减小,形成的泥膜中结合水含量逐渐变大,泥膜渗透系数减小至4.03×10^(-8)cm/s;改性海水泥浆中粒径小于75μm的细颗粒含量显著增加,静置24h后,泥浆上部呈现浑浊,下部依然存在较严重的沉淀;当CMC掺量达到0.16%时,改性海水泥浆2h泌水率小于10%,成膜渗透流量小于0.01m^(3)/m^(2),可以保证泥浆短期稳定性并形成致密泥膜。     

基于正交设计的水泥基注浆材料配比试验研究

应用正交设计方法,以水料比、硫铝酸盐水泥掺量、硅灰掺量定为3个因素,每个因素设置了3个影响水平,按照正交表共计设计9组配比方案,并经由试验得到不同配比下注浆材料的出机流动度、90 min流动度、12 h抗压强度、1 d抗压强度、28 d抗压强度。采用极差分析,确定各影响因素敏感性,绘制直观分析图反映各因素对注浆材料流动度、抗压强度的影响,分析了各因素对注浆材料性能的影响规律。试验结果表明:当水料比为0.19,硫铝酸盐水泥掺量为13%,硅灰掺量为7%时水泥基注浆材料浆体出机流动度为385 mm,90 min流动度为350 mm,12 h抗压强度为4.8 MPa,1 d抗压强度为23.3 MPa,28 d抗压强度为86.9 MPa,均满足技术要求。