Improving pollutant emissions in diesel engines for heavy-duty transportation using retarded intake valve closing strategies

A combined theoretical and experimental study has been carried out to determine the real potential of reducing pollutant emissions in a HD diesel engine by means of retarding the intake valve closing. The effects produced by this alteration of the basic operation cycle have been examined by a preliminary modelling study, and from the obtained results, a modified camshaft was manufactured with a delayed intake valve closing of 60 crank angle degrees. Single-cylinder engine tests were carried out with this modified camshaft, and the emissions and fuel consumption were recorded. The results showed that the retarded intake valve closing can enhance the premixed combustion phase, and thus simultaneously reduce soot and NOx emissions. Moreover, the combustion process attained is extremely tolerant to exhaust gas recirculation, and by adoption of this measure, Euro-5 emissions limits can be achieved at the tested conditions without after-treatment.     

Study of in-vehicle route guidance systems for improvement of right-side drivers in the Japanese traffic system

A country can adopt one of two standards for traffic flow — cars may travel on the left or right side of the road. When drivers who are accustomed to driving on the right side of the road drive on the left side, and vice versa, the mental workload is likely increased due to the driver’s unfamiliarity with a new language, the position of the driver’s seat, different driving directions, and other factors that differ from those of their home country. One method of doing this is to make sure that the in-vehicle route guidance information (RGI) is not overly complicated — thereby assisting drivers in improving their safety. Consequently, the aim of this study was to facilitate mobility and improve safety for natural right-side drivers driving temporarily in left-side traffic. In this study, driver behavior and workload — given various types of RGI — were evaluated in a driving simulator with a variety of prescribable test conditions. This research was composed of two experiments. In the first, various types of in-vehicle route guidance systems were tested and evaluated in terms of their characteristics and associated driver behaviors (while driving). In the second experiment, systemic factors and effectiveness were evaluated by two combined systems, arrow and map-type information, based on the results of the first experiment. In light of both experiments, the various types of route guidance systems were discussed in terms of their results. A navigation system was proposed to alleviate some of the secondary tasks such as route selection.     

Torque characteristics analysis for optimal design of a copper-layered eddy current brake system

An enhanced parametric model for a copper-layered eddy current electric machine (retarder) is introduced in this paper. The modeled torque characteristics of the copper-layered electromagnetic retarders are based on the results from a detailed electromagnetic finite element analysis (FEA) of these eddy current machines. The model uses a parameterized double-exponential function to model the steady state speed-torque characteristics of the retarder. The parameters are adjusted for optimal braking performance in conjunction with predicted speed-torque characteristics of a copper-layered retarder. A full vehicle model, along with the proposed retarder speed-torque model has been used to simulate a series braking events. The simulation results show that the peaks of the retarder speed-torque curves must be designed to occur within a specific range of speeds for optimal braking performance.     

Improving the predictiveness of the quasi-d combustion model for spark ignition engines with flexible intake systems

Fast and predictive simulation tools are prerequisites for pursuing simulation based engine control development. A particularly attractive tradeoff between speed and fidelity is achieved with a co-simulation approach that marries a commercial gas dynamic code WAVE™ with an in-house quasi-dimensional combustion model. Gas dynamics are critical for predicting the effect of wave action in intake and exhaust systems, while the quasi-D turbulent flame entrainment model provides sensitivity to variations of composition and turbulence in the cylinder. This paper proposes a calibration procedure for such a tool that maximizes its range of validity and therefore achieves a fully predictive combustion model for the analysis of a high degree of freedom (HDOF) engines. Inclusion of a charge motion control device in the intake runner presented a particular challenge, since anything altering the flow upstream of the intake valve remains “invisible” to the zero-D turbulence model applied to the cylinder control volume. The solution is based on the use of turbulence multiplier and scheduling of its value. Consequently, proposed calibration procedure considers two scalar variables (dissipation constant C _β and turbulence multiplier C _M ), and the refinements of flame front area maps to capture details of the spark-plug design, i.e. the actual distance between the spark and the surface of the cylinder head. The procedure is demonstrated using an SI engine system with dual-independent cam phasing and charge motion control valves (CMCV) in the intake runner. A limited number of iterations led to convergence, thanks to a small number of adjustable constants. After calibrating constants at the reference operating point, the predictions are validated for a range of engine speeds, loads and residual fractions.     

Perturbation/correlation based optimal internal combustion engine tuning

This paper addresses the application of the perturbation/correlation method to optimizing the torque output of internal combustion engines. This application was inspired by observations of the limitations in current techniques of the automotive performance tuning industry. Performance issues such as errors from true optimum spark timing and fuel injector pulse width values as well as convergence were considered for optimal tuning. The ability of the system to deal with engine cycle-to-cycle variations and their effect on input parameters is also analyzed.     

Off-set crack propagation analysis under mixed mode loadings

An assessment was carried out herein to study the eccentricity of cracks subjected to mixed-mode loadings. Several loading locations relative to a central line were selected to induce mixed-mode loadings, which were computed using a finite element method. An adaptive meshing technique was adopted during the simulation of crack propagation to ensure the singularity of stress at the tip of the crack. The stress intensity failure criterion was used and programmed, and the node splitting technique was used when the stress intensity factor reached the fracture toughness of the material to simulate crack propagations. It was found that large variations in the stress intensity factor were observed when off-set cracks were used, and that K _II decreased when loading distance increased, but increased when the off-set crack distance was increased. Both crack eccentricity and loading distance played important roles in producing mixed-mode loading, compared to the influence of central cracks. Correction factors were introduced to modify the calculation of stress intensity factors under mixed-mode loadings. Simulations of crack propagation were also conducted to study the effects of crack eccentricities and loading distances. It was found that the crack length, the loading distance relative to the central crack and the crack eccentricity dominated calculations of the integrity of cracked structures.     

Development of a semi-empirical friction model in automotive driveshaft joints

High speed and sport utility vehicles with large joint articulation angle demand lower friction in automotive driveshaft joints to meet noise and vibration comfort levels. Thus a more thorough understanding of internal friction characteristics and mechanisms is required. In this paper, a friction model in automotive driveshaft joints was developed through the use of test data from an instrumented Constant Velocity (CV) joint friction apparatus with actual driveshaft assemblies. Experiments were conducted under different realistic operating conditions of oscillatory speeds, CV joint articulation angles, lubrication, and torque. The experimental data was used to develop a physics-based semi-empirical CV joint internal friction model as a function of different CV joint operating parameters. It was found that the proposed friction model captures the experimental results well. Also the friction model estimates the generated axial force (GAF) in tripod CV joints well, which is the main source of force that causes vehicle vibration problems.     

Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Modified lateral control of an autonomous vehicle by look-ahead and look-down sensing

This paper presents a modified lateral control method for an autonomous vehicle with both look-ahead and look-down sensing systems. To cope with sensor noise and modeling uncertainty in the lateral control of the vehicle, a modified LMI-based H lateral controller was proposed, which uses the look-ahead information of the lateral offset error measured at the front of vehicle and the look-down information of the vehicle yaw angle error between the reference lane and the centerline of the vehicle. To verify the safety and the performance of the lateral control, a scaled-down vehicle was developed, and the positioning of the vehicle was estimated with USAT. The proposed controller, which uses both look-ahead and look-down information, was tested for lane changing and reference lane tracking with both simulation and experiment. The simulation and experimental results show that the proposed controller has better tracking and handling performance compared with a controller that uses only the look-ahead information of the target heading angle error.     

License plate extraction method for identification of vehicle violations at a railway level crossing

The primary cause of most railroad accidents is vehicle entry into railway level crossings despite warning messages. To identify drivers who violate railway level crossing regulations, vehicle license plate recognition can be applied at railway level crossings. The purpose of this paper is to present an effective method for extracting the license plate region from vehicle images taken at railway level crossings. The method proposed in this paper uses the variation in the gray-level values across the image of a license plate. For license plate region extraction, the character region is first recognized by identifying the character width and the difference between the background region and the character region. The license plate region is then extracted by finding the inter-character distance in the plate region. In addition, the license plate type is identified by the difference in the gray-level value between the background region and the character region. The proposed method is effective in solving the current challenges in extracting the license plate region from the damaged frames of license plates issued for domestic use, including new types of license plates. According to the experimental results, the proposed method yields a high extraction rate of 99.5% for vehicle license plates.