Approximate optimal AUTOSAR software components deploying approach for automotive E/E system

The AUTOSAR has been developed as the worldwide standard for automotive E/E software systems, making the electronic components of different suppliers to be employed universally. However, as the number of component-based applications in modern automotive embedded systems grows rapidly and the hardware topology becomes increasingly complex, deploying such large number of components in automotive distributed system in manual way is over-dependent on experience of engineers which in turn is time consuming. Furthermore, the resource limitation and scheduling analysis make the problems more complex for developers to find out an approximate optimal deploying approach in system integration. In this paper, we propose a novel method to deploy the AUTOSAR components onto ECUs with the following features. First, a clustering algorithm is designed for deploying components automatically within relatively low time complexity. Second, a fitness function is designed to balance the ECUs load. The goal of our approach is to minimize the communication cost over all the runnable entities while meeting all corresponding timing constraints and balancing all the ECUs load. The experiment results show that our approach is efficient and has well performance by comparing with other existing methods in specific and synthetic data set.     

废气旁通阀开度对增压直喷汽油机部分负荷性能的影响

汽油机节气门产生的节流损失对增压发动机泵气损失的影响相当严重,尤其是在中小负荷时,针对这一问题采用试验的方法研究了中小负荷下旁通阀开度对增压直喷汽油机性能的影响。研究结果表明,在节气门开度较小的小负荷工况下,涡轮增压器不宜工作,否则排气背压过大,对发动机非常不利;而废气旁通阀全开可以减小排气背压,能使发动机的动力性和经济性提高3%左右。对废气旁通阀的合理控制可以实现发动机在自然吸气和涡轮增压两种模式之间的转换。     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

基于ARENA的双车道超车视距设计风险评价

通过计算机仿真软件ARENA模拟双向两车道路段上不同的超车视距长度下的超车行为,并建立风险指标。风险指标主要根据超车动作结束时,超越车与对向车辆间的最短时间距离确定。一共确定了六个风险等级,用于评价不同设计时速下的各种PSD长度的风险。利用此方法可以很直接的评价超车视距设计的优劣。     

美国限速制定方法及启示

为使我国道路限速的制定更为合理,借鉴国外相关经验是必不可少的。总结了美国设置限速时考虑的主要因素、限速设置方法及其适用条件。对美国部分城市的州际道路及主干路的限速实施状况进行了分析,认为测速相机等自动执法设备的辅助使用能够在很大程度上提高驾驶人对限速的遵守程度。在借鉴美国限速方法及实施经验的基础上,指出我国在制定道路相关限速标准时,应结合国情确定限制速度与运行速度、设计速度之间的互动关系,以及限速与安全、执法等之间的关系。然后针对不同的道路类型、等级等特性研究采用不同的限速方案,解决速度区限速取值及不同速度区之间如何平滑过渡衔接等问题,明确了我国限速研究的基础性内容。     

TNFα、Leptin-Rb、NF-κB和PPAR-γ在酒精性肝病大鼠肝细胞中的表达

目的 探讨TNFα、NF-κB、Leptin-Rb和PPAR-γ等在大鼠酒精性肝病中与肝组织炎症、坏死和纤维化的关系.方法 胃造瘘法建立长期大鼠酒精性肝病模型,分别在第4、8、12、24和52周用免疫组化、原位杂交和RT-PCR技术检测不同阶段大鼠肝组织中TNFα、NF-κB、PPAR-γ和Leptin-Rb等的表达.结果 TNFα、NF-κB和Leptin-Rb水平在模型组大鼠肝细胞中,第8周表达逐渐增强,第24周起高水平表达一直持续至52周(P<0.01).PPAR-γ在对照组和第4、8周模型组肝细胞中表达最强,第12周表达开始减弱.TNFα和NF-κB在肝细胞中的表达呈明显正相关关系,与PPAR-γ则呈负相关关系(P<0.01).结论 TNFα和NF-κB与肝细胞病变程度有很好的一致性关系,Leptin-Rb在肝细胞的表达与肝纤维化发展相一致,PPAR-γ则刚好相反.     

掺锶磷酸钙骨水泥的体外细胞生物学性能评价及其与掺锶量的相关性

目的 评价"SrHPO4/Ca4(PO4)2O/CaHPO4"系掺锶磷灰石骨水泥的生物相容性及其与掺锶量的关系.方法 通过急性全身毒性、热原性、溶血性、体外细胞毒性以及成骨细胞在材料表面的黏附、增殖与表达等实验,检测材料的性能及生物降解潜能.结果 "SrHPO4/Ca4(PO4)2O/CaHPO4"系掺锶磷灰石骨水泥的急性全身毒性、热原性、溶血性、体外细胞毒性均为合格.Sr-CPC的热原性、溶血性以及碱性磷酸酶值与掺锶量呈非线性关系.结论 含锶磷酸钙骨水泥体外细胞生物相容性良好,是安全的新型骨组织工程支架材料.     

生存素在5-氟尿嘧啶诱导人绒癌细胞株JAR凋亡中的作用

目的探讨生存素(survivin)在化疗药物5-氟尿嘧啶(5-Fu)诱导的人绒癌细胞株(JAR)凋亡中的作用。方法用JAR细胞株进行培养传代,以不同浓度5-Fu作用于JAR细胞,MTT方法观察5-Fu对JAR细胞生长的抑制情况,流式细胞仪检测细胞凋亡率,用逆转录聚合酶链(RT-PCR)和免疫印迹技术(Western-blot)方法检测survivin基因和蛋白的表达。结果①5-Fu对JAR细胞的生长具有抑制作用,并有浓度和时间的依赖性;②5-Fu诱导JAR细胞凋亡,凋亡率随浓度而增加;③5-Fu作用后survivin基因和蛋白表达减少,随浓度增加而减少。结论5-Fu可能是通过降低survivin表达水平,诱导JAR细胞凋亡。