Ramsis眼点在汽车设计中的应用

Ramsis系统能根据不同参数调整人体模型、从设定的人体模型中提取眼点。介绍了Ramsis眼点的求取方法。以上海大众帕萨特轿车仪表盘可视区的求取为例，比较了使用Ramsis眼点集与使用SAE眼椭圆的区别：指出，SAE眼椭圆是从统计学角度描述驾驶员的眼点位置，而Ramsis眼点则从人体优化的角度描述眼点。     

"长安之星"微型客车车架刚度研究

通过试验和数值模拟，反求“长安之星”车架结构的弯曲和扭转刚度，建立了适用于“长安之星”车架结构的弯曲和扭转刚度测试的试验台，对其弯曲和扭转刚度进行了试验研究。在试验基础上，模拟了刚度测试过程中的约束和加载条件，进行了车架结构刚度的有限元分析。计算和试验结果的对比表明，二者吻合得较好。该研究结果为同类车型开发、改型及优化设计提供了技术手段和依据。     

振动压路机起振过程分析

运用机械系统虚拟样机软件ADAMS建立了振动压路机激振器的虚拟样机，并利用其进行了振动压路机起振过程的仿真研究，分析了液压系统压力对启动过程中档销受力及对动偏心块和固定偏心块运动学参数的影响。     

用于车身制造质量控制的白车身测点布置及优化

在对检测点进行分类定义后阐述了车身设计阶段各类测点的布置原则，在此基础上提出了面向制造偏差诊断的测点布置位置优化方法。     

金属带式无级变速器电液控制系统的试验研究

通过对金属带式无级变速液压控制系统功能进行分析，把该系统分为夹紧力控制和速比控制系统。设计了金属带式无级变速器电—液控制系统，对控制阀特性进行了研究，为夹紧力控制系统和速比控制系统分别设计了控制器。最后对所设计的CVT控制系统进行了实车道路试验，取得了较好的效果。     

基于案例推理的汽车维修专家系统

依据汽车维修行业领域的专家知识和实践经验，综合运用案例推理、模糊推理和缺省推理等方法，对汽车维修中的多种故障采取原因和症状相结合的维修思路进行推理机制的设置，建立基于案例推理、模糊推理和缺省推理相结合的、能迅速确定汽车维修方案的推理模型，建立了某企业汽车维修系统的原型系统。     

浅析钢筋混凝土双曲拱桥的拆除

本文通过对原淮阴市红卫桥拆除过程进行分析总结 ,初步探索了钢筋混凝土双曲拱桥的拆除工艺和方法     

高强力复合土工布在软基路堤中的应用

本文结合工程实例介绍采用高强力复合土工布处理软土地基路堤的设计、施工与应用效果     

Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Hub location with flow economies of scale

A characteristic feature of hub and spoke networks is the bundling of flows on the interhub links. This agglomeration of flows leads to reduced travel costs across the interhub links. Current models of hub location do not adequately model the scale economies of flow that accrue due to the agglomeration of flows. This paper shows that current hub location models, by assuming flow-independent costs, not only miscalculate total network cost, but may also erroneously select optimal hub locations and allocations. The model presented in this paper more explicitly models the scale economies that are generated on the interhub links and in doing so provides a more reliable model representation of the reality of hub and spoke networks.