一种天然气发动机尾气净化技术路线探索

为使天然气发动机满足现阶段排放要求,主流企业均采用当量燃烧+EGR+TWC技术路线,文章通过研究一种提高天然气发动机进气量的燃烧及相应的尾气净化技术,同样可以满足排放要求,且发动机无需EGR,结构简单,气耗更低,同时有效降低整车热负荷,为重型天然气发动机满足更高排放要求提供新的解决思路.     

客车操纵稳定性试验研究

根据相关标准对客车操纵稳定性的各项试验进行评分,进而评价其操纵稳定性的优劣。试验结果表明,该车的转向轻便性,稳态回转性能较好,而转向回正性能较差。此研究结果能够为该客车操纵稳定性的进一步改进提供依据。     

从LS-DYNA到PAM-CRASH的模型转换及侧面碰撞仿真

研究了有限元模型从LS-DYNA向PAM-CRASH的转换方法,利用该方法成功实现了某轿车整车模型的转换。在转换模型的基础上,通过加入车门内饰、假人和移动障碍壁模型,建立了完整的整车侧面碰撞模型。将仿真计算结果和整车试验测试数据进行比较,验证了模型的有效性。     

沪嘉高速公路桥梁管理与养护技术

该文主要介绍了沪嘉高速公路运营以来的桥梁管理和养护技术,重点介绍了近年来在大交通流量状况下,对钢筋混凝土、预应力混凝土梁桥病害进行养护、维修的施工技术,可供类似工程参考。     

汽车品牌联合营销模式

文章阐述了品牌联合营销的竞争优势及其基本原则,并分析了汽车品牌联合营销的具体策略,指出合理制定汽车品牌联合营销策略能使汽车品牌营销获得应有的作用。     

Simulation of mixed gas formation for a spray-wall complex guided LPG direct injection engine

To obtain an ultralean air-fuel ratio and to reduce engine-out NOX and HC emissions induced by the richer mixture near the spark plug, a spray and wall complex guided combustion system has been developed by utilizing the fuel characteristics of LPG. The new combustion system configuration is optimized by using a commercial CFD code, FIRE V2013, and the reliability of the system has been experimentally demonstrated by Plane Laser-Induced Fluorescence (PLIF). The mixture formation in the new combustion system under part load (2,000 rpm) is numerically simulated. With an injection timing of 40°CA BTDC, the LPG spray which is injected from two upper holes, reaches the ignition point, and the other part of the LPG spray which is injected from the bottom hole, is directed to the ignition point through the vertical vortices at the same time. At the ignition timing of about 20°CA BTDC, the two-part mixtures have been shown to form a stable and richer stratified mixture around the ignition point, and the maximum global air-fuel ratio reaches to 60: 1.     

Robust control for four-wheel-independent-steering electric vehicle with steer-by-wire system

A four-wheel-independent-steering (4WIS) electric vehicle (EV) with steer-by-wire (SBW) system is proposed in this paper. The fast terminal sliding mode controller (FTSMC) is designed for the SBW system to suppress external disturbances. Taking unstructured and structured uncertainties into consideration, a robust controller is designed for the 4WIS EV utilizing μ synthesis approach and the controller order reduction is implemented based on Hankel-Norm approximation. Since sideslip angle is the feedback signal of robust controller and it is hard to measure, the extended Kalman filter (EKF) is employed to estimate sideslip angle. To evaluate the vehicle performance with the designed control system, step and sinusoidal steering maneuvers are simulated and analyzed. Simulation results show that the designed control system have good tracking ability, strong robust stability and good robust performance to improve vehicle stability and handing performance.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Effective method for knock signal denoising in internal combustion engine

Uncontrolled expansion of combustion wave in spark ignited internal combustion engine causes knock effect which seriously degrades efficiency and lifetime of the engine. Thus, accurate knock detection and control are essential for obtaining a desired performance from the engine. Usually, knock sensor is used to detect this phenomenon but it has limited accuracy especially at engine high-speed rotations because of natural vibration and external noises. In this study an effective method based on Non-Local Mean (NLM) algorithm has been proposed to improve the knock detection accuracy. This method is evaluated based on four different indicators and four engine cylinders. The results show 52.9 % improvement in knock detection. Also feasibility of real time execution of this method based on embedded hardware has been studied.     

交通信号灯相关标准及规范中存在的问题

分析了《道路交通信号灯》(GB14887)《中华人民共和国道路交通全法实施条例》及《道路交通信号灯安装规范》(GB14886)对交通信号灯的技术要求,指出了标准及规范在实际应用中存在的问题,针对问题提出了相应的解决对策,同时对相关的标准及规范给出了改进建议。