Oriented review to potential simulator for faults modeling in diesel engine

This paper presents a literature review on most of the faults and their models that are considered on a diesel engine. Several faults that may be produced on diesel engine have been analyzed, classified, modeled, and their influences on the global system have been shown. Thus, this paper aims to prepare an important data base on diesel engine faults which may help researchers to develop precise strategies on diesel engine fault diagnosis and prognosis, and also it helps in the development of diesel engine simulators aiming to study the behavior of the diesel engine in the presence of faults. Different fault models such as analytical, empirical, degradation models which may be represented as function of time or as function of the number of cycles, data driven models such as neural network models, or simply constant are presented and analyzed. The global overall models for diesel engine integrating faults are expressed. And finally, the use of these models with the most common failure density distribution functions is proposed giving a more realistic approach to our study.     

Advantages of twin rudder system with asymmetric wing section aside a propeller

This study presents a new twin rudder system with asymmetric wing section, aside a propeller, as a new category energy saving device (ESD) for ships. The energy saving principle of the new ESD, which is called “Gate rudder”, is described and its applicability on a large bulk carrier is explored using experimental and numerical methods. The study makes emphasis on the cost-effectiveness of the proposed ESD and presents a potential energy saving up to 7–8 % with the new device as well as an attractive return investment in 0.37–0.9 year. These estimations are based on the conventional powering methods, whereas the accuracy of the ESD design method is confirmed by model test measurements.     

Application of digital image correlation method to in-situ dynamic strain measurement

Application of digital image correlation (DIC) method to determination of in-situ dynamic strain is presented in this study. Firstly, an integrative software is programmed based on the DIC algorithms and point-wise least-squares fitting technique. Then, simulated speckle images are generated to study the computational accuracy of this software. The experimental setup and procedures for measuring in-situ dynamic strain through both DIC and strain gauge are proposed. The DIC results are close to those measured by strain gauge. This fact reveals that DIC is a practical and effective tool for in-situ dynamic strain measurement. Finally, the full-field in-situ dynamic strain of another specimen is measured by DIC, and the overall distribution of the strain in the measurement area is clearly shown.     

CT reconstruction with priori MRI images through multi-group datasets expansion

Computed tomography (CT) reconstruction with a well-registered priori magnetic resonance imaging (MRI) image can improve reconstruction results with low-dose CT, because well-registered CT and MRI images have similar structures. However, in clinical settings, the CT image of patients does not always match the priori MRI image because of breathing and movement of patients during CT scanning. To improve the image quality in this case, multi-group datasets expansion is proposed in this paper. In our method, multi-group CT-MRI datasets are formed by expanding CT-MRI datasets. These expanded datasets can also be used by most existing CT-MRI algorithms and improve the reconstructed image quality when the CT image of a patient is not registered with the priori MRI image. In the experiments, we evaluate the performance of the algorithm by using multi-group CT-MRI datasets in several unregistered situations. Experiments show that when the CT and priori MRI images are not registered, the reconstruction results of using multi-group dataset expansion are better than those obtained without using the expansion.     

Seafarers’ perceptions of competency in risk assessment and management: an empirical study

Past analysis of accident investigations suggest an absence of or inadequate practices of risk assessment and management on board vessels. Although the International Management Code for the Safe Operation of Ships and for Pollution Prevention (ISM Code) requires that the risk management process must not only be correctly formulated and implemented but also be periodically evaluated in order to verify that these objectives are attained, the correct and effective implementation and application of the process cannot be achieved without active involvement of competent seafarers on board. Due to the limited investigation of seafarers’ competencies in risk management, the reasons for the inadequacies in the process that are leading to accidents were not evident. Hence, using a survey, this paper conducted a pilot study investigating seafarers’ perceptions of competency in the various components of the risk management process conducted on board vessels. The findings of this paper suggest an overall satisfaction with the risk assessment process. However, there is certainly room for improvement as far as seafarers’ performance is concerned. The findings of this paper provided valuable insights into the current training regimes in the area of risk assessment and management paving the way towards enhanced safety procedures on board vessels.     

载货汽车主气瓶不同气压时制动性能分析

汽车综合性能测试仪VGQT测试分析结果表明,货车在主制动气瓶压力不同时,各轴制动气室所能达到的最大压力也不相同[1],除此之外,本试验中N类载货汽车0型制动试验表明,主气瓶气压不同时,各轴气室制动压力变化曲线以及有效最大减速度MFDD也不相同。载货汽车绝大部分是用于长途运输,尤其是N2、N3类载货汽车,由于其满载质量大,长途运输中制动效能对于行驶安全性有着很大的影响,尤其在我国西南部山道纵横,长时间上下坡很容易造成制动器的热衰退,这是引起交通事故的主要诱因之一[2,3]。本文以实际试验结果为研究对象,分析了主气瓶在不同压力下各轴制动气室压力的变化以及0型制动试验中制动气压曲线的变化和有效最大减速度的变化,这对于行驶安全性和燃油经济性都有一定的意义,进而对排放和环境造成影响。     

应试教育方式适合航海英语教学

航海英语教学在受制于船员英语适任评估的前提下,应充分理解并应用考试的选择功能,提高学生航海英语学习的效果和应试的能力,为国际和国内航运业提供合格的人才。     

Automatic outer surface extraction of femoral head in CT images

Computer-aided hip surgery planning and implant design applications require accurate segmentation of femoral head and proximal acetabulum. An accurate outer surface extraction of femoral head using marching cubes algorithm remains challenging due to deformed shapes and extremely narrow inter-bone regions. In this paper, we present an automatic and fast approach for segmentation of femoral head and proximal acetabulum which leads to accurate and compact representation of femoral head using marching cubes algorithm. At first, valley-emphasized images are constructed from original images so that valleys stand out in high relief. Otsu’s multiple thresholding technique is applied to seperate the images into bone and non-bone classes. Region growing method and threedimensional (3D) morphological operations are performed to fill holes in the bone. In the reclassification process, the bone regions are further segmented, and the boundaries of the bone regions are further refined based on Bayes decision rule. Finally, marching cubes algorithm is applied to reconstruct a 3D model and extract the outer surface of femoral head and proximal acetabulum. Experimental results show that this method is an accurate segmentation technique for femoral head and proximal acetabulum and it can be applied as a tool in medical practice.     

Comparison on travel scheduling between driving and walking trips by habitual car users

Research on walking behavior has become increasingly more important in the field of transportation in the past decades. However, the study of the factors influencing the scheduling decisions related to walking trips and the exploration of the differences between travel modes has not been conducted yet. This paper presents a comparison of the scheduling and rescheduling decisions associated with car driving trips and walking trips by habitual car users using a data set collected in Valencia (Spain) in 2010. Bivariate probit models with sample selection are used to accommodate the influence of pre-planning on the decision to execute a travel as pre-planned or not. The explicative variables considered are: socio-economic characteristics of respondents, travel characteristics, and facets of the activity executed at origin and at destination including the scheduling decisions associated with them. The results demonstrate that a significant correlation exists between the choices of pre-planning and rescheduling for both types of trips. Whether for car driving or walking trips, the scheduling decisions associated with the activity at origin and at destination are the most important explicative factors of the trip scheduling and rescheduling decisions. However, the rescheduling of trips is mainly influenced by modifications in the activity at destination. Some interesting differences arise regarding the rescheduling decision processes between travel modes: if pre-planned, walking trips are less likely to be modified than car driving trips, showing a more rigid rescheduling behavior.