On the observability of the fortnightly cycle of the Tagus estuary turbid plume using MODIS ocean colour images

Using three years (2003 to 2005) of MODIS-Aqua normalized water-leaving radiance at 551 nm this paper shows a fortnightly cycle in the Tagus estuary turbid plume. The Tagus estuary is one of the largest estuaries of the west coast of Europe and is located in the most populated area of Portugal, including the capital Lisbon. The turbid plume has been detected by the backscattering characteristics of the surface waters in the vicinity of the estuary mouth. In fortnightly scales, the turbid plume has smaller dimensions during and after neap tides and higher dimensions during and after spring tides. This is most probably associated with the fortnightly spring–neap tidal cycle and the consequent increase in turbidity inside the estuary during spring tides. During the summer weak spring tides (tidal amplitude approximately 2.5 m) no turbid plume is observed for an entire fortnightly cycle. Outside the summer months, precipitation, river discharge and winds, were found to increase the turbid area, but the fortnightly cycle appears to be superimposed on the large time-scale variability, and present throughout the year.     

On the numerical accuracy of the prediction of resistance coefficients in ship stern flow calculations

This article presents a study on the accuracy of the numerical determination of the friction and pressure resistance coefficients of ship hulls. The investigation was carried out for the KVLCC2 tanker at model- and full-scale Reynolds numbers. Gravity waves were neglected, i.e., we adopted the so-called double-model flow. Single-block grids with H–O topology were adopted for all the calculations. Three eddy viscosity models were employed: the one-equation eddy viscosity and the two-equation models proposed by Menter and the TNT version of the two-equation k-ω model. Verification exercises were performed in sets of nearly geometrically similar grids with different densities in the streamwise, normal, and girthwise directions. The friction and pressure resistance coefficients were calculated for different levels of the iterative error and for computational domains of different size. The results show that on the level of grid refinement used, it is possible to calculate the viscous resistance coefficients in H–O grids that do not match the ship contour with a numerical uncertainty of less than 1%. The differences between the predictions of different turbulence models were larger than the numerical uncertainty; however, these differences tended to decrease with increases in the Reynolds number. The pressure resistance was remarkably sensitive to domain size and far-field boundary conditions. Either a large domain or the application of a viscous–inviscid interaction procedure is needed for reliable results. This work was presented in part at the International Conference on Computational Methods in Marine Engineering—MARINE 2007, Barcelona, June 3–4, 2007.     

Unsteady finite-depth effects during resistance tests on a ship model in a towing tank

This paper covers an extension of the study of Doctors et al. (J Ship Res 52(4):263–273, 2008) on oscillations in wave resistance during the constant-velocity phase of a towing-tank resistance test on a ship model to the case of relatively shallow water. We demonstrate here that the unsteady effects are very prominent and that it is essentially impossible to achieve a steady-state resistance curve in a towing tank of typical proportions for a water-depth-to-model-length ratio of 0.25. This statement is particularly true in the speed region near a depth Froude number of unity. However, on the positive side, we show here that an application of unsteady linearized wave-resistance theory provides an excellent prediction of the measured total resistance, when one accounts for the form factor in the usual manner. Finally, a simple application of the results to the planning and analysis of towing-tank tests is presented.     

Integrated reliability and sizing optimization of a large composite structure

In this paper, we present the application of probabilistic design modeling and reliability-based design optimization (RBDO) methodology to the sizing optimization of a composite advanced submarine sail structure under parametric uncertainty. With the help of probabilistic sensitivity analysis, the influence of individual random variables on each structural failure mode is examined, and the critical modes are treated as probabilistic design constraints under consistent lower bounds on the corresponding reliability indices. Whereas the failure modes are evaluated for structural components in the solution of the RBDO problem, the overall system reliability is also evaluated as a post-optimization step. The results indicate that in comparison to a deterministic-optimum design, the structural mass of the probabilistic optimum design is slightly higher when consistent probabilistic constraints are imposed, and the overall structural stiffness is found to be more critical than individual component laminate ply thicknesses in meeting the specified design constraints. Moreover, the post-optimality analysis shows that the overall system failure probability of the probabilistic optimum design is more than 50% lower than that of the deterministic optimal design with less than 5% penalty in structural mass.     

Influence of the slice position on chloride migration tests for concrete in marine conditions

Chloride migration tests are used to measure the concrete capacity to inhibit chloride attack. Many researchers carry out this test in a slice of concrete extracted from the central part of cylindrical specimens, discarding about 75% of the concrete used to mold the specimens. This fact generated the question: would it be possible to extract more slices from a same specimen without losing the confidence in the results? The main purpose of this work is to answer this question. Moreover, another aim of this study was to show the difference of chloride penetration between finished faces and the formwork surfaces of concrete beams and slabs. The results indicated that it is possible to use more slices of a single specimen for a chloride migration test. Moreover, it was demonstrated that there is a significant difference of chloride penetration between the finished surface and the formwork surface of the specimens.     

A study of vibration and vibration control of ship structures

This paper examines the vibration characteristics and vibration control of complex ship structures. It is shown that input mobilities of a ship structure at engine supports, due to out-of-plane force or bending moment excitations, are governed by the flexural stiffness of the engine supports. The frequency averaged input mobilities of the ship structure, due to such excitations, can be represented by those of the corresponding infinite beam. The torsional moment input mobility at the engine support can be estimated from the torsional response of the engine bed section under direct excitation. It is found that the inclusion of ship hull and deck plates in the ship structure model has little effect on the frequency-averaged response of the ship structure. This study also shows that vibration propagation in complex ship structures at low frequencies can be attenuated by imposing irregularities to the ring frame locations in ships. Vibration responses of ship structures due to machinery excitations at higher frequencies can be controlled by structural modifications of the local supporting structures such as engine beds in ships.     

Water entry of a bow-flare ship section with roll angle

The two-dimensional water entry of a bow-flare ship section with constant roll angle, or heel angle, was studied by using a boundary element method. The fully nonlinear free surface conditions and exact body boundary conditions were satisfied. Nonviscous flow separation from the knuckles of the section or from the curved bottom could be simulated. The numerical calculations were compared with existing experimental results. First, the effects of roll angle were investigated and then the characteristics associated with large roll angles were examined in particular. The evolution of the free surfaces and the pressure distributions on the section surface are illustrated and the influence of nonviscous flow separation from the leeward section surface is discussed.     

一种单缸护箱结构的集装箱散货装箱机

由于环保标准的提高,以及用户对一些货物破损率有较高要求,散货装集装箱运输方式的应用越来越多,比较典型的是块煤装集装箱运输。但是,这种运输方式在我国应用历史较短,散货装入集装箱比较困难。要充分发挥运力,降低成本,就必须将集装箱装满,而集装箱除底面外,侧面和上面均不能承受较大的力,如果要把集装箱倾斜过来装箱,就要解决箱体侧面受压的问题。     

螺旋式卸车机PLC控制系统设计

螺旋式卸车机PLC控制系统采用PLC控制交流接触器,从而控制各机构的交流电动机动作,实现相应的功能,同时在系统故障时发出声光报警信号或自动停车,以保护整个控制系统及设备安全。     

堆场底层取料控制的改进

取料机在取堆场底层的物料时,剩余的垛底厚度主要由两个因素决定：一是俯仰下限位;二是俯仰极限限位。这两个限位整定一般是根据堆场的标准高度确定的。通常情况下,港口的堆场标高是一个定值,整个堆场上所有的垛位都处在同一水平面上。理论上,取料机底层取料后的剩余垛底厚度是一个固定的整定值。但北方的港口大都是建立在填海造陆的软基基础上的,经过几年使用后,由于堆存煤炭的重力作用,堆场发生了不同程度的沉降,