Travel time estimation oriented freeway sensor placement problem considering sensor failure

Optimal sensor placement on freeway corridor is of great interest to transportation authorities. However, current traffic sensors are easily subject to various failures. Therefore, it is necessary to incorporate sensor failure into the optimal sensor placement model. In this article, a two-stage stochastic model is proposed for the purpose of travel time estimation on freeway corridor. To balance the effectiveness and reliability, a stochastic conditional value at risk (CVaR) model is also proposed. Since both models are too complicated, a customized genetic algorithm is developed. Numerical experiments show that considering sensor failure makes a significant performance improvement in the sensor placement pattern. Sensitivity analysis is also applied to investigate the impact of a number of allowable sensors and different traffic sensor failure probability.     

基于SHEL和三角模糊数理论的地铁钻爆法施工安全评价方法研究

为合理应用决策数据中不同专家的背景知识,找出地铁施工过程中安全测评体系的关注重点,根据地铁施工的特点和SHEL安全模型理论,建立以人-软件(L-S)、人-硬件(L-H)、人-环境(L-E)和人-人(L-L)4个环节为基础的钻爆法地铁施工安全指标体系。请专家给出指标语义评价等级和指标权重语义评价等级,并根据其与三角模糊数的对应关系分别得出三角模糊数评价值。针对不同专家的重要性程度差异,提出基于三角模糊数的群一致性评价方法,得出专家综合权重,集结评价数据,最终得到安全评价结果。最后,对青岛地铁1号线过海段进行实例分析。结果表明,该方法可以解决群评价过程中专家个体权威与群体共识难以兼顾的问题,能够充分利用群决策中的原始评价信息,提高地铁施工安全水平评价的准确性。     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

高速公路景观设计初探

就高速公路景观设计进行了探讨.     

船舶上层建筑重量重心对其固有频率的影响

在船舶设计、建造过程中及船舶建造完成后,有时上层建筑的固有频率与主机、螺旋桨的激励频率相接近。想要通过一些简单有效的手段对船舶进行修改,使上层建筑的固有频率避开激励源频率以避免共振。本文利用大型通用有限元分析软件Ansys,以某300,000吨级原油船为研究对象,对上层建筑的重量和重心高度如何影响上层建筑的首阶横向、纵向固有频率进行灵敏度分析,以求找到简单有效的、适于工程实际中改变船舶上层建筑固有频率的方法。     

基于系统动力学的大连市出租车保有量预测

采用系统动力学模型,找出影响出租车规模内外因素间的因果关系,包括经济、人口、机动车保有量、出行需求、政策等.在系统结构分析和因果反馈分析的基础上建立了出租车系统,以大连市出租车相关统计数据进行仿真计算,分析了不同的发展政策对出租车系统的影响,提出相应的建议和对策.     

堆料机悬臂皮带机打滑原因的分析与处理

堆料机的悬臂皮带机在使用过程中,当悬臂上仰角度达到正常需要工作角度的某一值时,皮带会发生打滑现象,尤其是应用于运送铁矿和采用螺旋张紧或液压张紧装置张紧的悬臂皮带机,更易出现打滑的现象。通过实例分析其打滑机理,并提出解决办法。     

嘉陵江草街航电枢纽工程马鞍山人工砂石加工系统优化及改造

文章论述重庆嘉陵江草街航电枢纽工程中马鞍山人工骨料加工系统的设计规模、生产工艺流程和设备配置情况,总结分析运行中存在的问题,提出了技术改进措施。系统优化改造后实际生产能力得到显著提高。     

轨道交通高架桥下部结构水平变形计算及控制探讨

城市轨道交通高架桥梁设计中,由于多采用无缝线路设计来提供列车运行时的平稳性和舒适性,因此轨道结构多为长钢轨形式。由此对高架桥梁的下部结构产生了一个特殊的长轨纵向力。为使下部结构变形在纵向力作用下控制在规范要求的范围内,必须在设计中对下部结构在长轨纵向力作用下的表现进行研究。通过明珠线一期北延伸工程的设计实践认为:在长轨高架桥下部结构设计中合理地选择墩柱及基础形式是控制下部结构变形的关键,也是优化下部结构设计的关键。