Impact behavior modeling of motorcycle front wheel-tire assembly

Experiments were conducted to investigate the influence of certain parameters that affect the impact response of the motorcycle front wheel-tire assembly under various impact conditions. Impact tests were conducted according to 2 _ν ^{5 − 1} fractional factorial design using a pendulum impact test apparatus with impact speed, impact mass, tire inflation pressure level, striker geometry, and impact location as design factors. Significant factors influencing the response of the wheel-tire assembly were identified. Coefficients for each factor were also determined, and empirical models were then developed for each response. An analysis indicates that the developed models fit well within the experimental ranges of the respective factors. However, for several interaction effects, the models become unrealistic, whereby they give certain deformation values when approaching zero impact mass and/or zero impact velocity. This is not consistent with the mechanics of the physical world, as there should not be any significant deformation when delivered impact energy is small enough. Efforts have been made in developing better models to resolve the inconsistency and to include a wider range, especially considering the case of the lower limit of experimental factors, which are an impact mass of 51.18 kg and/or an impact velocity of 3 m s⁻¹ (10.8 km/h) down to zero. The minimum amount of impact energy required to produce the onset of observable deformation on the wheel was incorporated in the development of new models. Finally, the present models have been developed not only to cover the lower regions but also to range up to the upper limits of the factors, which are an impact mass of 101.33 kg and an impact velocity of 6 m s⁻¹ (21.6 km/h).     

Increase in particle number emissions from motor vehicles due to interruption of steady traffic flow

We assess the increase in particle number emissions from motor vehicles driving at steady speed when forced to stop and accelerate from rest. Considering the example of a signalized pedestrian crossing on a two-way single-lane urban road, we use a complex line source method to calculate the total emissions produced by a specific number and mix of light petrol cars and diesel passenger buses and show that the total emissions during a red light is significantly higher than during the time when the light remains green. Replacing two cars with one bus increased the emissions by over an order of magnitude.     

Approach to assess a fast welding simulation in an industrial environment — Application for an automotive welded part

Fusion welding processes are widely used for joining metal structures, such as pipes, ships, and cars. In general, these joining processes offer a very good compromise between reliability, safety, cost and maintenance which are important issues in the current economical context. The negative heat effects of welding, i.e. distortions and residual stresses of the welded parts, are well known and many researches in this field have already been done in the last decades in order to minimize them. On the experimental side, many sophisticated procedures have become state of the art to deal with this problem. On the computational side, the improvement of the simulation algorithms and the computing power enables the simulations of many physical phenomena occurring during the welding process. The implementation of welding simulation techniques is nevertheless not an easy task and often associated with expert knowledge which hinders their global application in an industrial environment. This paper is focused on the industrial requirements of a welding simulation software with special respect to the needs of the automotive industry. The necessary information to run a welding simulation and the expectations of a weld specialist without deep knowledge in numerical methods are investigated. These expectations are tested on an automotive welded assembly with a commercially available welding simulation software designed especially for the needs of the automotive industry. A welding experiment is done and the measured temperature distributions and distortions serve as reference to validate the simulation results. The result quality of the simulations of temperature fields and distortions is in best agreement with experimental data. The workflow is well adapted for the considered industrial requirements and the time-tosolution as well as the computational costs are acceptable, whereas the efficient calibration of the heat input model is still a point which will be further investigated in current and future research works.     

Direct method for optimal power management in hybrid electric vehicles

Hybrid electric vehicles are powered by an electric system and an internal combustion engine. The components of a hybrid electric vehicle need to be coordinated in an optimal manner to deliver the desired performance. This paper presents an approach based on direct method for optimal power management in hybrid electric vehicles with inequality constraints. The approach consists of reducing the optimal control problem to a set of algebraic equations by approximating the state variable which is the energy of electric storage, and the control variable which is the power of fuel consumption. This approximation uses orthogonal functions with unknown coefficients. In addition, the inequality constraints are converted to equal constraints. The advantage of the developed method is that its computational complexity is less than that of dynamic and non-linear programming approaches. Also, to use dynamic or non-linear programming, the problem should be discretized resulting in the loss of optimization accuracy. The propsed method, on the other hand, does not require the discretization of the problem producing more accurate results. An example is solved to demonstrate the accuracy of the proposed approach. The results of Haar wavelets, and Chebyshev and Legendre polynomials are presented and discussed.     

Comparisons of the environmental footprint of heavy vehicles in the UK and Switzerland

The European Union project Eureka Logchain Footprint is an ongoing project to identify road and rail vehicles by means of their environmental footprint as characterised by dynamic load, noise, ground borne vibrations and gaseous emissions induced by the vehicle. Part of the project involves the installation of road and rail footprint monitoring stations throughout Europe. This paper presents results of the road stations in Switzerland and the UK. Individual vehicle data from weigh-in-motion and noise are compared. The results indicate that a significant number of vehicles surpass the limits set in both countries. It was shown that the UK sites are generating higher noise levels than their Swiss counterparts; in part due to the much coarser aggregate embedded in the running course of the pavement employed in the UK. Such data can be used to create an incentive for vehicle types with a low footprint and a penalty for vehicles with a large footprint.     

Turbulence in coastal fronts near the mouths of Block Island and Long Island Sounds

Measurements of turbulence were performed in four frontal locations near the mouths of Block Island Sound (BIS) and Long Island Sound (LIS). These measurements extend from the offshore front associated with BIS and Mid-Atlantic Bight Shelf water, to the onshore fronts near the Montauk Point (MK) headland, and the Connecticut River plume front. The latter feature is closely associated with the major fresh water input to LIS. Turbulent kinetic energy (TKE) dissipation rate, ε, was obtained using shear probes mounted on an autonomous underwater vehicle. Offshore, the BIS estuarine outflow front showed, during spring season and ebb tide, maximum TKE dissipation rate, ε, estimates of order 10^− 5 W/kg, with background values of order 10^− 6 to 10^− 9 W/kg. Edwards et al. [Edwards, C.A., Fake, T.A., and Bogden, P.S., 2004a. Spring–summer frontogenesis at the mouth of Block Island Sound: 1. A numerical investigation into tidal and buoyancy-forced motion. Journal of Geophysical Research 109 (C12021), doi:10.1029/2003JC002132.] model this front as the boundary of a tidally driven, baroclinically adjusted BIS flow around the MK headland eddy. At the entrance to BIS, near MK, two additional fronts are observed, one of which was over sand waves. For the headland site front east of MK, without sand waves, during ebb tide, ε estimates of 10^− 5 to 10^− 6 W/kg were observed. The model shows that this front is at the northern end of an anti-cyclonic headland eddy, and within a region of strong tidal mixing. For the headland site front further northeast over sand waves, maximum ε estimates were of order 10^− 4 W/kg within a background of order 10^− 7–10^− 6 W/kg. From the model, this front is at the northeastern edge of the anti-cyclonic headland eddy and within the tidal mixing zone. For the Connecticut River plume front, a surface trapped plume, during ebb tide, maximum ε estimates of 10^− 5 W/kg were obtained, within a background of 10^− 6 to 10^− 8 W/kg. Of all four fronts, the river plume front has the largest finescale mean-square shear, S² ~ 0.15 s^− 2. All of the frontal locations had local values of the buoyancy Reynolds number indicating strong isotropic turbulence at the dissipation scales. Local values of the Froude number indicated shear instability in all of the fronts.     

Limitation of egg production in Calanus finmarchicus in the field: A stoichiometric analysis

The egg production of marine copepods correlates with a range of variables, including the availability of organic carbon (C), nitrogen (N) and the polyunsaturated fatty acids (PUFAs) 20:5(n−3) (EPA) and 22:6(n−3) (DHA). However, an understanding of which substrates limit egg production in the natural environment has yet to be reached. The quantities of C, N, EPA and DHA ingested, derived from parental biomass, and invested in eggs by female Calanus finmarchicus during a 5-day incubation experiment were examined using stoichiometric theory to determine which substrate was limiting. The majority of each substrate was derived from parental biomass, and therefore the existing stoichiometric theory is developed to include this route of supply. The females were essentially devoid of lipid reserves, as evidenced by the lack of the storage fatty acids 20:1(n−9) and 22:1(n−11), and carbon limitation was predicted under most of the scenarios examined. Nitrogen limitation was only apparent when carbon and nitrogen utilisation efficiencies were assumed to be high (0.5) and low (0.4) respectively. PUFAs were assumed to be utilised with high efficiency (0.9), and were never predicted to limit production. This work highlights the need for a more detailed understanding of the maintenance requirements that marine copepods have for C, N, EPA, and DHA and hence the efficiencies with these substrates can be utilised for growth.